Dohun Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dohun Kim has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
Jaye Koo
14 shared publicationsInchul Lee
Graduate Student, Korea Aerospace University, Goyang, Republic of Korea
5 shared publicationsKeonwoong Lee
5 shared publicationsMin Son
3 shared publicationsBongchul Shin
2 shared publicationsHongbeen Chang
The 4th R&D Institute, Agency for Defense Development
2 shared publications
Latest Publications
- 1 September 2016
- Published by Elsevier in Acta Astronautica
- Vol. 126, 528-535
Effects of kerosene heating on dynamic characteristics of GOx/kerosene combustor
- 1 September 2016
- Published by Elsevier in Acta Astronautica
- Vol. 126, 528-535
Effects of kerosene heating on dynamic characteristics of GOx/kerosene combustor
- 1 May 2016
- Published by Elsevier in Combustion and Flame
- Vol. 167, 1-13
Effects of pre-filled gas and spraying condition on ignition of oxygen/kerosene spray combustion
- 1 May 2016
- Published by Elsevier in Combustion and Flame
- Vol. 167, 1-13
Effects of pre-filled gas and spraying condition on ignition of oxygen/kerosene spray combustion
- 1 May 2016
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Propulsion and Power
- Vol. 32 (3) , 533-541
Effects of Wall-Injection Length on Spray and Combustion in a Coaxial Porous Injector
The mixing performance of an injector determines the combustion performance of a bipropellant rocket engine. In the previous study, a novel coaxial porous injector concept was developed to improve the mixing performance of a shear coaxial injector. It demonstrated a higher characteristic velocity efficiency than that of a typical shear coaxial injector. To clarify the efficiency-improving mechanism of a coaxial porous injector, the combustion flowfields of both injectors were visualized using a high-speed shadowgraph technique. The effect of geometry factors on the spray core length and the combustion performance as well as the differences in the reactive spray behavior between the coaxial porous injector and the shear coaxial injector were observed. The coaxial porous injector with a different wall-injection length showed higher characteristic velocity efficiencies, shorter spray core lengths, and thicker phase-change patterns at the spray core boundary. Changes in wall-injection length had a nonmonotonic effect on both the spray core length and the characteristic velocity efficiency. As opposed to the expected results, the coaxial porous injector with the highest combustion efficiency showed the longest spray core length. The phase-change pattern width, caused by the evaporation of liquid fuel droplets, was proportional to the efficiency.
- 1 May 2016
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Propulsion and Power
- Vol. 32 (3) , 533-541
Effects of Wall-Injection Length on Spray and Combustion in a Coaxial Porous Injector
The mixing performance of an injector determines the combustion performance of a bipropellant rocket engine. In the previous study, a novel coaxial porous injector concept was developed to improve the mixing performance of a shear coaxial injector. It demonstrated a higher characteristic velocity efficiency than that of a typical shear coaxial injector. To clarify the efficiency-improving mechanism of a coaxial porous injector, the combustion flowfields of both injectors were visualized using a high-speed shadowgraph technique. The effect of geometry factors on the spray core length and the combustion performance as well as the differences in the reactive spray behavior between the coaxial porous injector and the shear coaxial injector were observed. The coaxial porous injector with a different wall-injection length showed higher characteristic velocity efficiencies, shorter spray core lengths, and thicker phase-change patterns at the spray core boundary. Changes in wall-injection length had a nonmonotonic effect on both the spray core length and the characteristic velocity efficiency. As opposed to the expected results, the coaxial porous injector with the highest combustion efficiency showed the longest spray core length. The phase-change pattern width, caused by the evaporation of liquid fuel droplets, was proportional to the efficiency.
- 1 April 2016
- Published by The Korean Society of Propulsion Engineers in Journal of the Korean Society of Propulsion Engineers
- Vol. 20 (2) , 39-45
Disintegration Mechanism of a Coaxial Porous Injector
- 1 April 2016
- Published by The Korean Society of Propulsion Engineers in Journal of the Korean Society of Propulsion Engineers
- Vol. 20 (2) , 39-45
Disintegration Mechanism of a Coaxial Porous Injector
- 1 August 2015
- Published by The Korean Society of Propulsion Engineers in Journal of the Korean Society of Propulsion Engineers
- Vol. 19 (4) , 61-68
Comparison between GOx/Kerosene and GN2O/Ethanol Reactive Spray in a Subscale Liquid Rocket Engine
- 1 August 2015
- Published by The Korean Society of Propulsion Engineers in Journal of the Korean Society of Propulsion Engineers
- Vol. 19 (4) , 61-68
Comparison between GOx/Kerosene and GN2O/Ethanol Reactive Spray in a Subscale Liquid Rocket Engine
- 22 January 2015
- Published by Springer Nature in Journal of Visualization
- Vol. 18 (4) , 645-653
Ignition of nitrous oxide and ethanol spray in a subscale thruster
- 22 January 2015
- Published by Springer Nature in Journal of Visualization
- Vol. 18 (4) , 645-653
Ignition of nitrous oxide and ethanol spray in a subscale thruster
- 1 December 2014
- Published by The Korean Society of Propulsion Engineers in Journal of the Korean Society of Propulsion Engineers
- Vol. 18 (6) , 11-18
Visualization of Transient Ignition Flow-field in a 50 N Scale N2O/C2H5OH Thruster
- 1 December 2014
- Published by The Korean Society of Propulsion Engineers in Journal of the Korean Society of Propulsion Engineers
- Vol. 18 (6) , 11-18
Visualization of Transient Ignition Flow-field in a 50 N Scale N2O/C2H5OH Thruster
- 1 November 2014
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Propulsion and Power
- Vol. 30 (6) , 1620-1627
Combustion Characteristics of a Coaxial Porous Injector
A coaxial porous injector was proposed for gas–liquid combustion for improved mixing performance compared to a conventional shear coaxial injector. The coaxial porous injector discharged a gas jet in a direction normal to the center liquid core, and it was surmised that the momentum transfer from the radial gas jet to the axial liquid jet occurred more efficiently than with a traditional shear coaxial injector. To validate the effectiveness of this idea, the combustion performances of a coaxial porous injector and a shear coaxial injector were compared by conducting a hot-firing test using nitrous oxide-ethanol as propellant. The momentum flux ratio at the injector tip was selected as a spraying condition index, and the characteristic velocity efficiency was considered as a combustion performance parameter. The coaxial porous injector demonstrated higher combustion efficiency than the conventional shear coaxial injector, especially at lower-momentum flux ratio conditions. In addition, the comparison of spray images between the shear coaxial and coaxial porous injectors under ambient conditions supported the results of the hot-firing experiment.
- 1 November 2014
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Propulsion and Power
- Vol. 30 (6) , 1620-1627
Combustion Characteristics of a Coaxial Porous Injector
A coaxial porous injector was proposed for gas–liquid combustion for improved mixing performance compared to a conventional shear coaxial injector. The coaxial porous injector discharged a gas jet in a direction normal to the center liquid core, and it was surmised that the momentum transfer from the radial gas jet to the axial liquid jet occurred more efficiently than with a traditional shear coaxial injector. To validate the effectiveness of this idea, the combustion performances of a coaxial porous injector and a shear coaxial injector were compared by conducting a hot-firing test using nitrous oxide-ethanol as propellant. The momentum flux ratio at the injector tip was selected as a spraying condition index, and the characteristic velocity efficiency was considered as a combustion performance parameter. The coaxial porous injector demonstrated higher combustion efficiency than the conventional shear coaxial injector, especially at lower-momentum flux ratio conditions. In addition, the comparison of spray images between the shear coaxial and coaxial porous injectors under ambient conditions supported the results of the hot-firing experiment.
- 9 January 2014
- Published by Springer Nature in Journal of Thermal Science
- Vol. 23 (1) , 60-67
Breakup structure of two-phase jets with various momentum flux from a porous injector
- 9 January 2014
- Published by Springer Nature in Journal of Thermal Science
- Vol. 23 (1) , 60-67
Breakup structure of two-phase jets with various momentum flux from a porous injector
- 1 January 2014
- Published by Begell House Inc. Publishers in Atomization and Sprays
- Vol. 24 (1) , 1-22
MACROSCOPIC SPRAY CHARACTERISTICS OF A POROUS INJECTOR
The concept of coaxial porous injector design for gas-liquid mixing involves improved momentum transfer between the gas and liquid jets by changing the gas injecting direction of a conventional liquid-centered shear coaxial injector from parallel to perpendicular using porous material. Cold-flow tests of the coaxial porous injector and the shear coaxial injector in two-dimensional configurations were carried out to compare the macroscopic characteristics of sprays from each injector and to understand the effects of spraying conditions on the breakup length and the spray angle. The spray patterns were visualized using the shadowgraphy technique. The shadowgraph images recorded in high speed were post-processed to detect the breakup length and the spray angle. The post-processing code filters the dynamic pixels, and leaves the stationary pixels, which corresponds to the liquid core and the background. The most significant differences between the porous injector and the shear injector in the two-dimensional configurations were the spray angle and the uniformity of the disintegrated liquid jet. The liquid column from the shear injector was not split off entirely, and only the portion at the interface between the gas and liquid jet was atomized by the shear force. On the other hand, the liquid jet from the porous injector dispersed more widely, and was disintegrated into droplets more completely in most experimental cases of similar axial momentum flux ratio conditions at the injector tip, and it was thought that an optimal porous element length for the best mixing performance exists at certain injection conditions.
- 1 January 2014
- Published by Begell House Inc. Publishers in Atomization and Sprays
- Vol. 24 (1) , 1-22
MACROSCOPIC SPRAY CHARACTERISTICS OF A POROUS INJECTOR
The concept of coaxial porous injector design for gas-liquid mixing involves improved momentum transfer between the gas and liquid jets by changing the gas injecting direction of a conventional liquid-centered shear coaxial injector from parallel to perpendicular using porous material. Cold-flow tests of the coaxial porous injector and the shear coaxial injector in two-dimensional configurations were carried out to compare the macroscopic characteristics of sprays from each injector and to understand the effects of spraying conditions on the breakup length and the spray angle. The spray patterns were visualized using the shadowgraphy technique. The shadowgraph images recorded in high speed were post-processed to detect the breakup length and the spray angle. The post-processing code filters the dynamic pixels, and leaves the stationary pixels, which corresponds to the liquid core and the background. The most significant differences between the porous injector and the shear injector in the two-dimensional configurations were the spray angle and the uniformity of the disintegrated liquid jet. The liquid column from the shear injector was not split off entirely, and only the portion at the interface between the gas and liquid jet was atomized by the shear force. On the other hand, the liquid jet from the porous injector dispersed more widely, and was disintegrated into droplets more completely in most experimental cases of similar axial momentum flux ratio conditions at the injector tip, and it was thought that an optimal porous element length for the best mixing performance exists at certain injection conditions.