Ji Woon Park
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ji Woon Park has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Tetsuya Ishida
2 shared publicationsYun Mook Lim
2 shared publications- Yun Mook Lim
Department of Civil and Environmental Engineering, Yonsei University, Seoul, Republic of Korea
2 shared publications Chen Chen
1 shared publicationHai Fang
1 shared publicationHonglei Xie
1 shared publication
Latest Publications
- Open Access
- 10 September 2026
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 25
Tensile performance of bundled basalt fiber reinforced SHCC: Experimental investigation and rigid body spring modeling
- 10 September 2026
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 25
Open AccessTensile performance of bundled basalt fiber reinforced SHCC: Experimental investigation and rigid body spring modeling
- Open Access
- 21 April 2026
- Published by Elsevier in Construction and Building Materials
- Vol. 526
Micromechanical design strategy for enhancing tensile ductility of strain-hardening basalt fiber reinforced cementitious composites
- 21 April 2026
- Published by Elsevier in Construction and Building Materials
- Vol. 526
Open AccessMicromechanical design strategy for enhancing tensile ductility of strain-hardening basalt fiber reinforced cementitious composites
- Open Access
- 1 December 2025
- Published by Elsevier in Cement and Concrete Composites
- Vol. 167
The rate-dependent fiber-matrix interface in ultra high-performance fiber reinforced concrete: Interface property determination
- 1 December 2025
- Published by Elsevier in Cement and Concrete Composites
- Vol. 167
Open AccessThe rate-dependent fiber-matrix interface in ultra high-performance fiber reinforced concrete: Interface property determination
- 20 February 2025
- Published by Elsevier in Structures
- Vol. 73
Fatigue and tensile performance of bridge link slab using multilayered 3D textile reinforced cementitious composite (3D-TRCC)
- 20 February 2025
- Published by Elsevier in Structures
- Vol. 73
Fatigue and tensile performance of bridge link slab using multilayered 3D textile reinforced cementitious composite (3D-TRCC)
- 6 December 2017
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 26 (5) , 465-469
Feasibility study to control fiber distribution for enhancement of composite properties via three-dimensional printing
The distribution of fibers in the composite (which takes into account both their locations and orientations) is one of the important factors that affect the mechanical properties of FRCs. However, this parameter depends on various factors during composite fabrication, and controlling the distribution of fibers in the produced material represents a significant challenge. In this study, the applicability of three-dimensional (3D) printing technique for controlling fiber distributions was evaluated. The fibers fabricated using a 3D printer were placed inside a mold to produce cementitious composites. Three-point bending tests were conducted and the results of the experiment were discussed.
- 6 December 2017
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 26 (5) , 465-469
Feasibility study to control fiber distribution for enhancement of composite properties via three-dimensional printing
The distribution of fibers in the composite (which takes into account both their locations and orientations) is one of the important factors that affect the mechanical properties of FRCs. However, this parameter depends on various factors during composite fabrication, and controlling the distribution of fibers in the produced material represents a significant challenge. In this study, the applicability of three-dimensional (3D) printing technique for controlling fiber distributions was evaluated. The fibers fabricated using a 3D printer were placed inside a mold to produce cementitious composites. Three-point bending tests were conducted and the results of the experiment were discussed.