Lars Nilsson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Lars Nilsson has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Stig Stenström
Lund University , Lund , Sweden
4 shared publicationsChristophe Barbier
Gruvön Mill, Grums, Sweden
3 shared publicationsJan Forsberg
Environmental and Energy Systems, Karlstad University, Karlstad, Sweden
2 shared publicationsJohan Kullander
Department of Chemical Engineering, Karlstad University , Karlstad , Sweden
2 shared publicationsJonas Berghel
2 shared publications- Kamal Rezk
Pro2BE, The Research Environment for Processes and Products for a Circular Forest-Based Bioeconomy, Department of Engineering and Chemical Sciences, Karlstad University
2 shared publications
Latest Publications
- Open Access
- 2 April 2020
- Published by Taylor & Francis in Drying Technology
- Vol. 39 (10) , 1349-1358
Numerical model of water removal and air penetration during vacuum dewatering
Dewatering and air flow in high vacuum suction boxes was examined. The work was mainly numerical and was based on, and compared with, previously published experimental results of vacuum dewatering from laboratory equipment and from a pilot paper machine. A previously published numerical model for wet pressing is used as the basis for this work. The aims of this study were to find new fitting parameters that allows the previous model to be used for vacuum dewatering instead of pressing, and to examine two extensions to the original model. The results indicate that the new vacuum dewatering model for moisture can predict the dewatering behavior for several different experimental data series both from laboratory equipment and a pilot paper machine using the same set of fitting parameters. Two different numerical models for air flow through the paper sheet, during vacuum dewatering, were developed based on postulating that the decrease in moisture permeability is accompanied by a simultaneous increase in air permeability. The models for air flow can also be fitted to experimental data and predict the magnitudes of air flow during vacuum dewatering. The data sets for air flow exhibit a certain degree of operator dependence though, so that one set of fitting parameters is not enough for obtaining good agreement with all data sets.
- 2 April 2020
- Published by Taylor & Francis in Drying Technology
- Vol. 39 (10) , 1349-1358
Open AccessNumerical model of water removal and air penetration during vacuum dewatering
Dewatering and air flow in high vacuum suction boxes was examined. The work was mainly numerical and was based on, and compared with, previously published experimental results of vacuum dewatering from laboratory equipment and from a pilot paper machine. A previously published numerical model for wet pressing is used as the basis for this work. The aims of this study were to find new fitting parameters that allows the previous model to be used for vacuum dewatering instead of pressing, and to examine two extensions to the original model. The results indicate that the new vacuum dewatering model for moisture can predict the dewatering behavior for several different experimental data series both from laboratory equipment and a pilot paper machine using the same set of fitting parameters. Two different numerical models for air flow through the paper sheet, during vacuum dewatering, were developed based on postulating that the decrease in moisture permeability is accompanied by a simultaneous increase in air permeability. The models for air flow can also be fitted to experimental data and predict the magnitudes of air flow during vacuum dewatering. The data sets for air flow exhibit a certain degree of operator dependence though, so that one set of fitting parameters is not enough for obtaining good agreement with all data sets.
- 19 September 2018
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 33 (4) , 581-591
Through air drying assisted by infrared radiation: the influence of radiator power on drying rates and temperature
The use of infrared radiation for heating the web in the through air drying process was investigated in lab scale. The hypothesis was that infrared radiation should be a more efficient method to transfer drying energy to the wet web compared to hot air, but that a certain air flow is still required as a transport medium for the evaporated water. A trial program comprising handsheets made of two types of bleached chemical pulps, five grammages (15, 22, 30 and 60 g/m²), and dried with five radiator power levels was performed on a lab scale through air drying equipment. Drying times of the samples were determined from temperature data recorded with an infrared camera. The use of infrared radiation shortened drying times, especially for low grammage samples. The shortening of the drying time ranged between 10 and 45 %. The most substantial shortenings were obtained for the lowest grammages and the highest radiator power level. However, the increase of power did not linearly shorten drying time. After an initial shortening at the lowest power level, the positive effect of the IR heating decreased as the power was further increased.
- 19 September 2018
- Published by Walter de Gruyter GmbH in Nordic Pulp & Paper Research Journal
- Vol. 33 (4) , 581-591
Through air drying assisted by infrared radiation: the influence of radiator power on drying rates and temperature
The use of infrared radiation for heating the web in the through air drying process was investigated in lab scale. The hypothesis was that infrared radiation should be a more efficient method to transfer drying energy to the wet web compared to hot air, but that a certain air flow is still required as a transport medium for the evaporated water. A trial program comprising handsheets made of two types of bleached chemical pulps, five grammages (15, 22, 30 and 60 g/m²), and dried with five radiator power levels was performed on a lab scale through air drying equipment. Drying times of the samples were determined from temperature data recorded with an infrared camera. The use of infrared radiation shortened drying times, especially for low grammage samples. The shortening of the drying time ranged between 10 and 45 %. The most substantial shortenings were obtained for the lowest grammages and the highest radiator power level. However, the increase of power did not linearly shorten drying time. After an initial shortening at the lowest power level, the positive effect of the IR heating decreased as the power was further increased.
- 1 August 2016
- Published by Elsevier in Applied Thermal Engineering
- Vol. 106, 174-179
The small-scale production of hydrogen, with the co-production of electricity and district heat, by means of the gasification of municipal solid waste
- 1 August 2016
- Published by Elsevier in Applied Thermal Engineering
- Vol. 106, 174-179
The small-scale production of hydrogen, with the co-production of electricity and district heat, by means of the gasification of municipal solid waste
- 2 October 2014
- Published by Taylor & Francis in Drying Technology
- Vol. 33 (5) , 605-615
Simulation of Water Removal in Paper Based on a 2D Level-Set Model Coupled with Volume Forces Representing Fluid Resistance in 3D Fiber Distribution
A numerical model of a vacuum dewatering process was established with a level-set method to simulate two-phase flow in a two-dimensional paper sheet model with constructed volume forces representing flow resistance in a three-dimensional environment. Nine cases of various volume force representations were investigated by comparing numerical and experimental data. Based on the dry content and dwell time relation, the best model is obtained when accounting for in-plane flow resistance at the paper–wire interface. Compared to the other numerical cases, considering the blockage of the pore space, the top layer of the wire plays an essential role in determining the flow resistance during the vacuum process. To validate the maximum dewatering rate obtained in the model, new experimental data with a higher frequency of sampling are needed. The computational time for the two-phase flow models in this study is extensively reduced due to the removal of the internal structure. This distinction enables time-efficient simulations of the vacuum dewatering process in which several dewatering parameters such as the level of the vacuum, the influence of a moving vacuum pulse, and higher basis weights could be investigated.
- 2 October 2014
- Published by Taylor & Francis in Drying Technology
- Vol. 33 (5) , 605-615
Simulation of Water Removal in Paper Based on a 2D Level-Set Model Coupled with Volume Forces Representing Fluid Resistance in 3D Fiber Distribution
A numerical model of a vacuum dewatering process was established with a level-set method to simulate two-phase flow in a two-dimensional paper sheet model with constructed volume forces representing flow resistance in a three-dimensional environment. Nine cases of various volume force representations were investigated by comparing numerical and experimental data. Based on the dry content and dwell time relation, the best model is obtained when accounting for in-plane flow resistance at the paper–wire interface. Compared to the other numerical cases, considering the blockage of the pore space, the top layer of the wire plays an essential role in determining the flow resistance during the vacuum process. To validate the maximum dewatering rate obtained in the model, new experimental data with a higher frequency of sampling are needed. The computational time for the two-phase flow models in this study is extensively reduced due to the removal of the internal structure. This distinction enables time-efficient simulations of the vacuum dewatering process in which several dewatering parameters such as the level of the vacuum, the influence of a moving vacuum pulse, and higher basis weights could be investigated.
- 28 July 2014
- Published by Taylor & Francis in Drying Technology
- Vol. 32 (13) , 1587-1597
Stepwise Development of a Mathematical Model for Air Flow in Vacuum Dewatering of Paper
Part of the dewatering in a paper machine takes place via vacuum suction boxes situated below the moving web. In addition to the removal of liquid water, considerable amounts of air are sucked through the paper. The air flow that accompanies dewatering is a crucial parameter for the electricity consumption of a vacuum system. The present study models this air flow, combining differential conservation equations with fiber characterization. Measured air flow rates for different vacuum levels, basis weights, and pulp types are compared to model predictions. More than 70% of the data agree within the range of experimental error.
- 28 July 2014
- Published by Taylor & Francis in Drying Technology
- Vol. 32 (13) , 1587-1597
Stepwise Development of a Mathematical Model for Air Flow in Vacuum Dewatering of Paper
Part of the dewatering in a paper machine takes place via vacuum suction boxes situated below the moving web. In addition to the removal of liquid water, considerable amounts of air are sucked through the paper. The air flow that accompanies dewatering is a crucial parameter for the electricity consumption of a vacuum system. The present study models this air flow, combining differential conservation equations with fiber characterization. Measured air flow rates for different vacuum levels, basis weights, and pulp types are compared to model predictions. More than 70% of the data agree within the range of experimental error.
- 7 December 2013
- Published by Taylor & Francis in Drying Technology
- Vol. 32 (1) , 39-46
Air Flow and Compression Work in Vacuum Dewatering of Paper
Dewatering on the paper machine takes place by gravity, suction, pressing, and evaporation. Optimizing the operation of the vacuum system is important, since the electricity consumption of the vacuum pumps might be one-fifth of the total electricity consumption of the paper machine. Vacuum dewatering involves large volumes of air penetrating the web. The present study presents four sets of measured air flow rates useful for designing industrial equipment. The mass flux of air increases with increasing applied vacuum and decreases with increasing basis weight. Paper technological parameters, such as fiber size and fiber flexibility, also influence the mass flux.
- 7 December 2013
- Published by Taylor & Francis in Drying Technology
- Vol. 32 (1) , 39-46
Air Flow and Compression Work in Vacuum Dewatering of Paper
Dewatering on the paper machine takes place by gravity, suction, pressing, and evaporation. Optimizing the operation of the vacuum system is important, since the electricity consumption of the vacuum pumps might be one-fifth of the total electricity consumption of the paper machine. Vacuum dewatering involves large volumes of air penetrating the web. The present study presents four sets of measured air flow rates useful for designing industrial equipment. The mass flux of air increases with increasing applied vacuum and decreases with increasing basis weight. Paper technological parameters, such as fiber size and fiber flexibility, also influence the mass flux.
- 3 October 2013
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 27 (10) , 6333
Co-production of Pyrolysis Oil in District Heating Plants: Systems Analysis of Dual Fluidized-Bed Pyrolysis with Sequential Vapor Condensation
- 3 October 2013
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 27 (10) , 6333
Co-production of Pyrolysis Oil in District Heating Plants: Systems Analysis of Dual Fluidized-Bed Pyrolysis with Sequential Vapor Condensation
- 1 September 2013
- Published by Elsevier in Chemical Engineering Science
- Vol. 101, 543-553
Modelling of water removal during a paper vacuum dewatering process using a Level-Set method
- 1 September 2013
- Published by Elsevier in Chemical Engineering Science
- Vol. 101, 543-553
Modelling of water removal during a paper vacuum dewatering process using a Level-Set method
- 29 August 2013
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 27 (9) , 5313-5319
Co-production of Pyrolysis Oil in District Heating Plants: Systems Analysis of Dual Fluidized-Bed Pyrolysis with Sequential Vapor Condensation
- 29 August 2013
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 27 (9) , 5313-5319
Co-production of Pyrolysis Oil in District Heating Plants: Systems Analysis of Dual Fluidized-Bed Pyrolysis with Sequential Vapor Condensation
- 1 February 2013
- Published by Elsevier in Applied Energy
- Vol. 102, 484-491
Potential energy savings made by using a specific control strategy when tumble drying small loads
- 1 February 2013
- Published by Elsevier in Applied Energy
- Vol. 102, 484-491
Potential energy savings made by using a specific control strategy when tumble drying small loads