Dirk Holzhüter
Research Subjects
Dirk Holzhüter has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Christian Hühne
Technische Universität Braunschweig
3 shared publications - Jens Kosmann
Institute of Lightweight Systems
3 shared publications - Martin Johannes Schollerer
German Aerospace Center
3 shared publications - Oliver Volkerink
Institute of Mechanics and Adaptronics, Fakultät für Maschinenbau, Technische Universität Braunschweig, Braunschweig, Germany
2 shared publications - Patrick Adrian Makiela
Institute of Lightweight Systems
1 shared publication - Thomas Gesell
Institute of Lightweight Systems
1 shared publication
Latest Publications
- Open Access
- 25 December 2025
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 102 (15) , 1-38
Examination of film and paste adhesive behaviour under cryogenic conditions using a thick adherend shear test
- 25 December 2025
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 102 (15) , 1-38
Open AccessExamination of film and paste adhesive behaviour under cryogenic conditions using a thick adherend shear test
- 27 March 2019
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 95 (5-7) , 474-494
Strength prediction of adhesively bonded single lap joints with the eXtended Finite Element Method
Because of a planar load introduction, a high strength over weight ratio, avoidance of holes, corrosion resistance and component reduction, adhesively bonded joints attract increasing attention in lightweight construction. Nonetheless, a reliable prediction of the joints’ behaviour in terms of stress and strength is still a tremendous challenge.
- 27 March 2019
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 95 (5-7) , 474-494
Strength prediction of adhesively bonded single lap joints with the eXtended Finite Element Method
Because of a planar load introduction, a high strength over weight ratio, avoidance of holes, corrosion resistance and component reduction, adhesively bonded joints attract increasing attention in lightweight construction. Nonetheless, a reliable prediction of the joints’ behaviour in terms of stress and strength is still a tremendous challenge.
- 10 December 2018
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 95 (5-7) , 495-514
Surface toughening – a concept to decrease stress peaks in bonded joints
By using fiber-reinforced plastics as the material for lightweight structures, adhesive bonding becomes an increasingly focused solution for joining these components. In comparison to bolted joints, adhesive bonding has a lot of known benefits, e.g. sealing, no weakening of adherends and a homogeneous load transfer. However, the stress distributions in single-lap joints are not homogeneous all over. Both the shear and peel stress distribution have a peak at the overlap ends of the joint and a lower loaded part in the middle, as shown by Volkersen and Goland and Reissner. In order to reduce these stress concentrations, there are known concepts for the modification of the joint. In this paper, adherend chamfering, different adhesive spew fillet geometries, and the mixed adhesive joint are investigated and compared to a novel local adherend surface toughening concept by using a thermoplastic PVDF layer. A high-resolution digital image correlation is used to visualize the deformation in the bondline. While the state-of-the-art used concepts do not show a high increase of joint strength for single lap joints, the joint strength for the surface toughening specimens can be increased by up to 84%.
- 10 December 2018
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 95 (5-7) , 495-514
Surface toughening – a concept to decrease stress peaks in bonded joints
By using fiber-reinforced plastics as the material for lightweight structures, adhesive bonding becomes an increasingly focused solution for joining these components. In comparison to bolted joints, adhesive bonding has a lot of known benefits, e.g. sealing, no weakening of adherends and a homogeneous load transfer. However, the stress distributions in single-lap joints are not homogeneous all over. Both the shear and peel stress distribution have a peak at the overlap ends of the joint and a lower loaded part in the middle, as shown by Volkersen and Goland and Reissner. In order to reduce these stress concentrations, there are known concepts for the modification of the joint. In this paper, adherend chamfering, different adhesive spew fillet geometries, and the mixed adhesive joint are investigated and compared to a novel local adherend surface toughening concept by using a thermoplastic PVDF layer. A high-resolution digital image correlation is used to visualize the deformation in the bondline. While the state-of-the-art used concepts do not show a high increase of joint strength for single lap joints, the joint strength for the surface toughening specimens can be increased by up to 84%.