Vyacheslav S. Protsenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Vyacheslav S. Protsenko has a total of 149 co-authors. Here are the top co-authors by number of shared publications:
- F. I. Danilov
Ukrainian State University of Chemical Technology
71 shared publications - Tetiana E. Butyrina
Kryvyi Rih National University
19 shared publications Ukrainian State University of Chemical Technology
18 shared publications- Sergiy A. Korniy
Karpenko Physico-Mechanical Institute of the National Academy of Sciences of Ukraine, Lviv, Ukraine
14 shared publications F.I. Danilov
12 shared publications- Denys A. Shaiderov
Ukrainian State University of Science and Technologies
11 shared publications
Latest Publications
- 1 October 2026
- Published by SHEI Ukrainian State University of Chemical Technology in Voprosy Khimii i Khimicheskoi Tekhnologii
- No. 5
Protective and decorative zinc–iron–chromium multilayer coatings on steel
The main features of the electrodeposition process and the corrosion-protective properties of a Zn–Fe–Cr multilayer coating on a steel substrate were characterized. Individual coating layers were electrodeposited using zinc plating from an alkaline zincate electrolyte, iron plating from a slightly acidic citrate electrolyte based on Fe(III), and chromium plating from a sulfate-formate electrolyte based on Cr(III). The effect of electrodeposition conditions on the current efficiency was established. The corrosion-protective behavior of the multilayer coatings in a 3% NaCl solution was investigated using gravimetric measurements, corrosion potential measurements, and polarization studies. The optimal coating was found to consist of Zn (9 m) + Fe (3 m) + Cr (0.5 m). For this coating, the time to the appearance of red rust in a 3% NaCl solution was 480 h, which exceeded the corresponding value for a single-layer zinc coating. It was shown that the zinc layer provides sacrificial protection of the steel substrate, the intermediate iron layer facilitates deposition of the chromium finishing layer, while the chromium coating imparts protective and decorative properties to the surface.
- 1 October 2026
- Published by SHEI Ukrainian State University of Chemical Technology in Voprosy Khimii i Khimicheskoi Tekhnologii
- No. 5
Protective and decorative zinc–iron–chromium multilayer coatings on steel
The main features of the electrodeposition process and the corrosion-protective properties of a Zn–Fe–Cr multilayer coating on a steel substrate were characterized. Individual coating layers were electrodeposited using zinc plating from an alkaline zincate electrolyte, iron plating from a slightly acidic citrate electrolyte based on Fe(III), and chromium plating from a sulfate-formate electrolyte based on Cr(III). The effect of electrodeposition conditions on the current efficiency was established. The corrosion-protective behavior of the multilayer coatings in a 3% NaCl solution was investigated using gravimetric measurements, corrosion potential measurements, and polarization studies. The optimal coating was found to consist of Zn (9 m) + Fe (3 m) + Cr (0.5 m). For this coating, the time to the appearance of red rust in a 3% NaCl solution was 480 h, which exceeded the corresponding value for a single-layer zinc coating. It was shown that the zinc layer provides sacrificial protection of the steel substrate, the intermediate iron layer facilitates deposition of the chromium finishing layer, while the chromium coating imparts protective and decorative properties to the surface.
- 1 August 2026
- Published by SHEI Ukrainian State University of Chemical Technology in Voprosy Khimii i Khimicheskoi Tekhnologii
- No. 4
The use of deep eutectic solvents in the fabrication of electrocatalysts for green hydrogen production via seawater electrolysis: a mini-review
The growing demand for green hydrogen as an environmentally friendly energy carrier stimulates the search for new approaches to improving the efficiency of water electrolysis and expanding the resource base for its production. Seawater electrolysis is of particular interest because it can reduce the dependence of hydrogen energy technologies on limited freshwater resources. However, the practical implementation of this approach is complicated by the presence of chloride ions, the occurrence of competing anodic reactions, corrosion of electrode materials, and the formation of sparingly soluble deposits on electrode surfaces. This mini-review analyzes the current state of research on the use of deep eutectic solvents (DESs) for the synthesis of electrocatalysts intended for seawater electrolysis processes. The classification of DESs, their main physicochemical properties, and specific features in the electrochemical synthesis of functional materials are considered. The results of studies devoted to the DES-assisted synthesis of electrocatalysts for the hydrogen evolution reaction and oxygen evolution reaction are summarized, and examples of their application under seawater electrolysis conditions are analyzed. It is shown that the use of DESs offers broad opportunities for the development of highly efficient, selective, and corrosion-resistant electrode materials. Prospective directions for future research are discussed, including the development of new DES compositions, the design of multicomponent catalysts, the scale-up of electrodeposition technologies, and the integration of seawater electrolysis with alternative anodic processes to reduce the energy consumption of green hydrogen production.
- 1 August 2026
- Published by SHEI Ukrainian State University of Chemical Technology in Voprosy Khimii i Khimicheskoi Tekhnologii
- No. 4
The use of deep eutectic solvents in the fabrication of electrocatalysts for green hydrogen production via seawater electrolysis: a mini-review
The growing demand for green hydrogen as an environmentally friendly energy carrier stimulates the search for new approaches to improving the efficiency of water electrolysis and expanding the resource base for its production. Seawater electrolysis is of particular interest because it can reduce the dependence of hydrogen energy technologies on limited freshwater resources. However, the practical implementation of this approach is complicated by the presence of chloride ions, the occurrence of competing anodic reactions, corrosion of electrode materials, and the formation of sparingly soluble deposits on electrode surfaces. This mini-review analyzes the current state of research on the use of deep eutectic solvents (DESs) for the synthesis of electrocatalysts intended for seawater electrolysis processes. The classification of DESs, their main physicochemical properties, and specific features in the electrochemical synthesis of functional materials are considered. The results of studies devoted to the DES-assisted synthesis of electrocatalysts for the hydrogen evolution reaction and oxygen evolution reaction are summarized, and examples of their application under seawater electrolysis conditions are analyzed. It is shown that the use of DESs offers broad opportunities for the development of highly efficient, selective, and corrosion-resistant electrode materials. Prospective directions for future research are discussed, including the development of new DES compositions, the design of multicomponent catalysts, the scale-up of electrodeposition technologies, and the integration of seawater electrolysis with alternative anodic processes to reduce the energy consumption of green hydrogen production.
- 1 April 2026
- Published by SHEI Ukrainian State University of Chemical Technology in Voprosy Khimii i Khimicheskoi Tekhnologii
- No. 2
Corrosion–electrochemical behavior of Ni–Mo alloy electrodeposited from an electrolyte based on deep eutectic solvents
The corrosion–electrochemical behavior of nickel and nickel–molybdenum coatings electrodeposited from electrolytes based on deep eutectic solvents (DES) in a 3% NaCl aqueous solution was examined. The coatings were deposited from eutectic mixtures of choline chloride with ethylene glycol (ethaline) and urea (reline) at different current densities; for comparison, nickel coatings prepared using a conventional aqueous sulfate–chloride nickel-plating electrolyte were also studied. The corrosion characteristics were determined by potentiodynamic polarization with subsequent Tafel analysis to calculate the corrosion current density, corrosion potential, and polarization resistance. It was shown that coatings deposited from DES-based electrolytes exhibit higher corrosion resistance than those obtained from the aqueous electrolyte. The incorporation of molybdenum into the deposit was found to decrease the corrosion current density and increase the polarization resistance, while an increase in the Mo content in the alloy leads to further improvement in the anticorrosion properties of the coatings. It was also shown that, at similar molybdenum contents, coatings deposited from the reline-based electrolyte exhibit higher corrosion resistance than those obtained from ethaline, which is associated with the higher carbon and oxygen contents in such coatings and the formation of an additional barrier layer on the surface.
- 1 April 2026
- Published by SHEI Ukrainian State University of Chemical Technology in Voprosy Khimii i Khimicheskoi Tekhnologii
- No. 2
Corrosion–electrochemical behavior of Ni–Mo alloy electrodeposited from an electrolyte based on deep eutectic solvents
The corrosion–electrochemical behavior of nickel and nickel–molybdenum coatings electrodeposited from electrolytes based on deep eutectic solvents (DES) in a 3% NaCl aqueous solution was examined. The coatings were deposited from eutectic mixtures of choline chloride with ethylene glycol (ethaline) and urea (reline) at different current densities; for comparison, nickel coatings prepared using a conventional aqueous sulfate–chloride nickel-plating electrolyte were also studied. The corrosion characteristics were determined by potentiodynamic polarization with subsequent Tafel analysis to calculate the corrosion current density, corrosion potential, and polarization resistance. It was shown that coatings deposited from DES-based electrolytes exhibit higher corrosion resistance than those obtained from the aqueous electrolyte. The incorporation of molybdenum into the deposit was found to decrease the corrosion current density and increase the polarization resistance, while an increase in the Mo content in the alloy leads to further improvement in the anticorrosion properties of the coatings. It was also shown that, at similar molybdenum contents, coatings deposited from the reline-based electrolyte exhibit higher corrosion resistance than those obtained from ethaline, which is associated with the higher carbon and oxygen contents in such coatings and the formation of an additional barrier layer on the surface.
- Open Access
- 25 December 2025
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Chemistry and Technologies
- Vol. 33 (4) , 1026-1044
ELECTRODEPOSITION OF Ni-BASED COMPOSITE COATINGS CONTAINING CERIUM COMPOUNDS FROM A DEEP EUTECTIC SOLVENT AND THEIR ELECTROCATALYTIC PERFORMANCE
This work examines the electrodeposition of Ni-based composite coatings containing cerium compounds from a eutectic mixture of choline chloride and urea (reline), a typical deep eutectic solvent. The data reveal that depending on the concentrations of NiCl2×6H2O and CeCl3×7H2O dissolved in reline, coatings containing up to 49 wt.% cerium, present as embedded CeO2, can be formed within an electrochemically deposited nanocrystalline nickel matrix. Variation of the Ni(II) and Ce(III) salt concentrations strongly influences the resulting surface morphology. Reaction schemes for the formation of these composite coatings are proposed, and cyclic voltammetry with successive scan cycles was used to identify the potential windows in which the relevant electrochemical reactions occur in reline-based solutions. The deposited coatings were tested as electrocatalysts for water electrolysis in 1 M NaOH. Special attention was paid to the electrocatalytic activity of the Ni-based composite coatings toward the anodic oxidation of urea, a potential alternative to the oxygen evolution reaction in green hydrogen production. Incorporation of CeO2 into the nickel matrix led to a pronounced enhancement of electrocatalytic activity for hydrogen evolution, oxygen evolution and urea oxidation in alkaline aqueous solution. The proposed composite coatings may find application as multifunctional catalysts for green hydrogen generation. Moreover, adjusting the Ni(II) and Ce(III) concentrations in the deep eutectic solvent-based plating bath enables flexible and controlled tuning of the electrocatalytic behavior of deposited coatings.
- 25 December 2025
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Chemistry and Technologies
- Vol. 33 (4) , 1026-1044
Open AccessELECTRODEPOSITION OF Ni-BASED COMPOSITE COATINGS CONTAINING CERIUM COMPOUNDS FROM A DEEP EUTECTIC SOLVENT AND THEIR ELECTROCATALYTIC PERFORMANCE
This work examines the electrodeposition of Ni-based composite coatings containing cerium compounds from a eutectic mixture of choline chloride and urea (reline), a typical deep eutectic solvent. The data reveal that depending on the concentrations of NiCl2×6H2O and CeCl3×7H2O dissolved in reline, coatings containing up to 49 wt.% cerium, present as embedded CeO2, can be formed within an electrochemically deposited nanocrystalline nickel matrix. Variation of the Ni(II) and Ce(III) salt concentrations strongly influences the resulting surface morphology. Reaction schemes for the formation of these composite coatings are proposed, and cyclic voltammetry with successive scan cycles was used to identify the potential windows in which the relevant electrochemical reactions occur in reline-based solutions. The deposited coatings were tested as electrocatalysts for water electrolysis in 1 M NaOH. Special attention was paid to the electrocatalytic activity of the Ni-based composite coatings toward the anodic oxidation of urea, a potential alternative to the oxygen evolution reaction in green hydrogen production. Incorporation of CeO2 into the nickel matrix led to a pronounced enhancement of electrocatalytic activity for hydrogen evolution, oxygen evolution and urea oxidation in alkaline aqueous solution. The proposed composite coatings may find application as multifunctional catalysts for green hydrogen generation. Moreover, adjusting the Ni(II) and Ce(III) concentrations in the deep eutectic solvent-based plating bath enables flexible and controlled tuning of the electrocatalytic behavior of deposited coatings.
- Open Access
- 22 December 2025
- Published by Lithuanian Academy of Sciences in Chemija
- Vol. 36 (4) , 245–254
An integral metric for evaluating electrocatalytic activity
This study introduces an integral metric of electrocatalytic activity, which is based on the comparison of the area under the polarisation curve in current density vs overpotential coordinates over a specific chosen overpotential range. This metric is applied to evaluate and compare several electrocatalysts, allowing for a more comprehensive understanding of electrocatalytic performance. Unlike traditional metrics, which characterise electrocatalyst behaviour under specific conditions (e.g. a particular overpotential or current density), the proposed integral metric provides a broader evaluation over a wide operational range. This approach is particularly useful for electrocatalysts with different Tafel slopes and polarisation characteristics. The metric is shown to be invariant to the shape of the polarisation curve and can be applied even when the exact form of the analytical dependence is unknown. The application of this metric holds promise for both fundamental studies in electrocatalysis and for practical applications in
- 22 December 2025
- Published by Lithuanian Academy of Sciences in Chemija
- Vol. 36 (4) , 245–254
Open AccessAn integral metric for evaluating electrocatalytic activity
This study introduces an integral metric of electrocatalytic activity, which is based on the comparison of the area under the polarisation curve in current density vs overpotential coordinates over a specific chosen overpotential range. This metric is applied to evaluate and compare several electrocatalysts, allowing for a more comprehensive understanding of electrocatalytic performance. Unlike traditional metrics, which characterise electrocatalyst behaviour under specific conditions (e.g. a particular overpotential or current density), the proposed integral metric provides a broader evaluation over a wide operational range. This approach is particularly useful for electrocatalysts with different Tafel slopes and polarisation characteristics. The metric is shown to be invariant to the shape of the polarisation curve and can be applied even when the exact form of the analytical dependence is unknown. The application of this metric holds promise for both fundamental studies in electrocatalysis and for practical applications in
- Open Access
Effect of Na+ vs. K+ Cations and Carbonate Presence on Urea Oxidation Reaction Coupled with Green Hydrogen Production in Alkaline Media: A Voltammetric and Electrochemical Impedance Spectroscopy Study
This work reports the electrochemical behavior of a nickel hydroxide electrode, electrodeposited in a deep eutectic solvent (DES), in alkaline solutions of varying composition, aiming to elucidate the influence of the cation (Na+ vs. K+), urea, and carbonate ions on the mechanism and kinetics of anodic processes. Cyclic voltammetry and electrochemical impedance spectroscopy were employed to analyze the electrochemical responses of electrode processes in alkaline water electrolysis systems. For the urea oxidation reaction (UOR), the frequency-dependent characteristics were thoroughly characterized, and the impedance response was simulated according to the Armstrong–Henderson equivalent circuit. It was found that the addition of urea significantly transforms the impedance structure, sharply reducing the polarization resistance and increasing the pseudo-capacitive component of the constant phase element at low frequencies, indicating activation of the slow steps of urea oxidation via a direct mechanism and the formation of an extended adsorptive surface. It was demonstrated that, unlike conventional alkaline electrolysis where KOH-based systems are generally more effective, urea-assisted systems exhibit superior performance in NaOH-based electrolytes, which provides more favorable kinetics for the electrocatalytic urea oxidation process. Furthermore, the accumulation of carbonate ions was shown to negatively affect UOR kinetics by increasing polarization resistance and partially blocking surface sites, highlighting the necessity of controlling electrolyte composition in practical systems. These findings open new opportunities for the rational design of efficient urea-assisted electrolyzers for green hydrogen generation.
Open AccessEffect of Na+ vs. K+ Cations and Carbonate Presence on Urea Oxidation Reaction Coupled with Green Hydrogen Production in Alkaline Media: A Voltammetric and Electrochemical Impedance Spectroscopy Study
This work reports the electrochemical behavior of a nickel hydroxide electrode, electrodeposited in a deep eutectic solvent (DES), in alkaline solutions of varying composition, aiming to elucidate the influence of the cation (Na+ vs. K+), urea, and carbonate ions on the mechanism and kinetics of anodic processes. Cyclic voltammetry and electrochemical impedance spectroscopy were employed to analyze the electrochemical responses of electrode processes in alkaline water electrolysis systems. For the urea oxidation reaction (UOR), the frequency-dependent characteristics were thoroughly characterized, and the impedance response was simulated according to the Armstrong–Henderson equivalent circuit. It was found that the addition of urea significantly transforms the impedance structure, sharply reducing the polarization resistance and increasing the pseudo-capacitive component of the constant phase element at low frequencies, indicating activation of the slow steps of urea oxidation via a direct mechanism and the formation of an extended adsorptive surface. It was demonstrated that, unlike conventional alkaline electrolysis where KOH-based systems are generally more effective, urea-assisted systems exhibit superior performance in NaOH-based electrolytes, which provides more favorable kinetics for the electrocatalytic urea oxidation process. Furthermore, the accumulation of carbonate ions was shown to negatively affect UOR kinetics by increasing polarization resistance and partially blocking surface sites, highlighting the necessity of controlling electrolyte composition in practical systems. These findings open new opportunities for the rational design of efficient urea-assisted electrolyzers for green hydrogen generation.
- Open Access
- 28 November 2025
- Published by MDPI AG in Preprints.org
Effect of Na⁺ vs. K⁺ Cations and Carbonate Presence on Urea Oxidation Reaction Coupled with Green Hydrogen Production in Alkaline Media: A voltammetric and Electrochemical Impedance Spectroscopy Study
This work reports the electrochemical behavior of a nickel hydroxide electrode, electrodeposited in a deep eutectic solvent (DES), in alkaline solutions of varying composition, aiming to elucidate the influence of the cation (Na+ vs. K+), urea, and carbonate ions on the mechanism and kinetics of anodic processes. Cyclic voltammetry and electrochemical impedance spectroscopy were employed to analyze the electrochemical responses of electrode processes in alkaline water electrolysis systems. For the urea oxidation reaction (UOR), the frequency-dependent characteristics were thoroughly characterized, and the impedance response was simulated according to the Armstrong–Henderson equivalent circuit. It was found that the addition of urea significantly transforms the impedance structure, sharply reducing the polarization resistance and increasing the pseudo-capacitive component of the constant phase element at low frequencies, indicating activation of the slow steps of urea oxidation via a direct mechanism and the formation of an extended adsorptive surface. It was demonstrated that, unlike conventional alkaline electrolysis where KOH-based systems are generally more effective, urea-assisted systems exhibit superior performance in NaOH-based electrolytes, which provides more favorable kinetics for the electrocatalytic urea oxidation process. Furthermore, the accumulation of carbonate ions was shown to negatively affect UOR kinetics by increasing polarization resistance and partially blocking surface sites, highlighting the necessity of controlling electrolyte composition in practical systems. These findings open new opportunities for the rational design of efficient urea-assisted electrolyzers for green hydrogen generation.
- 28 November 2025
- Published by MDPI AG in Preprints.org
Open AccessEffect of Na⁺ vs. K⁺ Cations and Carbonate Presence on Urea Oxidation Reaction Coupled with Green Hydrogen Production in Alkaline Media: A voltammetric and Electrochemical Impedance Spectroscopy Study
This work reports the electrochemical behavior of a nickel hydroxide electrode, electrodeposited in a deep eutectic solvent (DES), in alkaline solutions of varying composition, aiming to elucidate the influence of the cation (Na+ vs. K+), urea, and carbonate ions on the mechanism and kinetics of anodic processes. Cyclic voltammetry and electrochemical impedance spectroscopy were employed to analyze the electrochemical responses of electrode processes in alkaline water electrolysis systems. For the urea oxidation reaction (UOR), the frequency-dependent characteristics were thoroughly characterized, and the impedance response was simulated according to the Armstrong–Henderson equivalent circuit. It was found that the addition of urea significantly transforms the impedance structure, sharply reducing the polarization resistance and increasing the pseudo-capacitive component of the constant phase element at low frequencies, indicating activation of the slow steps of urea oxidation via a direct mechanism and the formation of an extended adsorptive surface. It was demonstrated that, unlike conventional alkaline electrolysis where KOH-based systems are generally more effective, urea-assisted systems exhibit superior performance in NaOH-based electrolytes, which provides more favorable kinetics for the electrocatalytic urea oxidation process. Furthermore, the accumulation of carbonate ions was shown to negatively affect UOR kinetics by increasing polarization resistance and partially blocking surface sites, highlighting the necessity of controlling electrolyte composition in practical systems. These findings open new opportunities for the rational design of efficient urea-assisted electrolyzers for green hydrogen generation.
- Open Access
- 20 November 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (22) , 10415
Investigation of Structural, Magnetic, Optical, and Photocatalytic Properties of Fe/CoFe2O4 Composite
A Fe/CoFe2O4 nanocomposite was synthesized in one step by a hydrothermal method by processing the created iron and cobalt hydroxocomplexes. For precise characterization of the structure and morphology, X-ray diffraction (XRD), Fourier transform infrared spectroscopy, scanning electron microscopy, and ultraviolet–visible diffuse reflectance spectroscopy (UV-vis-DRS) were used. It was found that the obtained samples have a pronounced spinel crystalline structure, with the presence of metallic iron. The crystal size was determined by various methods and was 93–104 nm. The saturation magnetization, determined from the hysteresis loop, was 189.24 Emu/g, and the force coefficient was 602 Oe. UV-vis-DRS studies showed a band gap of 2.1 eV. The photocatalytic degradation of ibuprofen, streptocide, furacilin, methylene blue, and tetracycline was investigated under the influence of UV radiation in the presence of a photocatalyst. It was confirmed that the rate of degradation of pollutants obeys pseudo-first-order kinetics. Analysis of the constant rate of reactions showed that in order of decreasing stability, pharmaceutical drugs can be dissolved as follows: ibuprofen → streptocide → furatsilin → methylene blue → tetracycline. It was found that the ratio of photocatalyst and hydrogen peroxide concentrations is important for the destruction of more stable pollutants. The effect of hydrogen peroxide and catalyst concentrations is extremely strong. For unstable compounds, the most influential factor is the duration of treatment.
- 20 November 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (22) , 10415
Open AccessInvestigation of Structural, Magnetic, Optical, and Photocatalytic Properties of Fe/CoFe2O4 Composite
A Fe/CoFe2O4 nanocomposite was synthesized in one step by a hydrothermal method by processing the created iron and cobalt hydroxocomplexes. For precise characterization of the structure and morphology, X-ray diffraction (XRD), Fourier transform infrared spectroscopy, scanning electron microscopy, and ultraviolet–visible diffuse reflectance spectroscopy (UV-vis-DRS) were used. It was found that the obtained samples have a pronounced spinel crystalline structure, with the presence of metallic iron. The crystal size was determined by various methods and was 93–104 nm. The saturation magnetization, determined from the hysteresis loop, was 189.24 Emu/g, and the force coefficient was 602 Oe. UV-vis-DRS studies showed a band gap of 2.1 eV. The photocatalytic degradation of ibuprofen, streptocide, furacilin, methylene blue, and tetracycline was investigated under the influence of UV radiation in the presence of a photocatalyst. It was confirmed that the rate of degradation of pollutants obeys pseudo-first-order kinetics. Analysis of the constant rate of reactions showed that in order of decreasing stability, pharmaceutical drugs can be dissolved as follows: ibuprofen → streptocide → furatsilin → methylene blue → tetracycline. It was found that the ratio of photocatalyst and hydrogen peroxide concentrations is important for the destruction of more stable pollutants. The effect of hydrogen peroxide and catalyst concentrations is extremely strong. For unstable compounds, the most influential factor is the duration of treatment.