Olena S. Panchenko
Olena S. Panchenko has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Ihor V. Satin
Design and Technology Institute of Municipal Economy Kyiv National University of Construction and Architecture Acting deputy director, Scientific State Enterprise ORСID ID Research
5 shared publications - Oleksandr Kravchenko
State Enterprise "Scientific, Research, Design and Technology Institute of Municipal Economy
5 shared publications - Serhii V. Khytruk
Scientific, Research Design and Technology Institute of Municipal Economy State Enterprise Kyiv Ukraine
2 shared publications - Tetiana Arhatenko
Kyiv National University of Construction and Architecture
2 shared publications - Tetiana Khomutetska
Kyiv National University of Construction and Architecture
2 shared publications - Tetyana I. Romanova
PhD, Head of the Laboratory, Scientific, Research, Design and Technology Institute of Municipal Economy, State Enterprise, Kyiv
2 shared publications
Latest Publications
- Open Access
- 20 June 2025
- Published by Kyiv National University of Construction and Architecture in Environmental safety and natural resources
- Vol. 54 (2) , 34-50
Estimation of debris waste generation
As of the beginning of 2022, Ukraine had approximately 8 million residential buildings with a total residential area of 892.1 million square meters. The number of apartments in residential buildings and non-residential structures in Ukraine totaled 15.5 million units. Due to hostilities and regular shelling, the number of damaged and destroyed residential buildings is increasing daily. As of January 2024, over 250,000 buildings have been damaged or destroyed, including 222,000 private homes, over 27,000 multi-apartment buildings, and 526 dormitories. The direct damage from the destruction of these objects is estimated at 58.9 billion USD. The regions with the most destroyed residential buildings include Donetsk, Kyiv, Luhansk, Kharkiv, Chernihiv, and Kherson. The generation of a large amount of debris waste requires planning for the demolition of destroyed buildings, dismantling of rubble, transportation to temporary waste storage sites, and the planning and selection of equipment for processing debris waste. Currently, Ukraine lacks an official methodology for estimating the volume of debris waste. To provide scientifically grounded methodological recommendations for estimating the amount of debris waste, the experience of various countries that have experienced technological disasters or natural disasters was studied, including Japan, Canada, and countries in the Middle East. The experience of managing debris waste in the communities of Chernihiv, Kyiv, and Mykolaiv regions was also examined. As a result of reviewing international experience, it was determined that the most appropriate approach is to use specific waste generation indicators per unit area – the waste generation rate. It is accepted that the area used to determine the volume of debris waste should be within the boundaries of the destruction or demolition (section, floor, or part of the building). A calculation of the waste generation rate was conducted based on the consumption of primary materials for typical series of multi-apartment residential buildings, monolithic-frame multi-apartment residential buildings, and residential buildings in cottage developments, including buildings of preschool and general secondary education institutions and hospitals.The resulting waste generation rates can be used to estimate the calculated amount of waste generated due to the damage or destruction of residential buildings, buildings of general secondary and preschool education institutions, and healthcare facilities as a result of hostilities, terrorist acts, sabotage, or work to eliminate their consequences. The waste generation rates do not apply to engineering structures, transportation infrastructure, or non-residential buildings.
- 20 June 2025
- Published by Kyiv National University of Construction and Architecture in Environmental safety and natural resources
- Vol. 54 (2) , 34-50
Open AccessEstimation of debris waste generation
As of the beginning of 2022, Ukraine had approximately 8 million residential buildings with a total residential area of 892.1 million square meters. The number of apartments in residential buildings and non-residential structures in Ukraine totaled 15.5 million units. Due to hostilities and regular shelling, the number of damaged and destroyed residential buildings is increasing daily. As of January 2024, over 250,000 buildings have been damaged or destroyed, including 222,000 private homes, over 27,000 multi-apartment buildings, and 526 dormitories. The direct damage from the destruction of these objects is estimated at 58.9 billion USD. The regions with the most destroyed residential buildings include Donetsk, Kyiv, Luhansk, Kharkiv, Chernihiv, and Kherson. The generation of a large amount of debris waste requires planning for the demolition of destroyed buildings, dismantling of rubble, transportation to temporary waste storage sites, and the planning and selection of equipment for processing debris waste. Currently, Ukraine lacks an official methodology for estimating the volume of debris waste. To provide scientifically grounded methodological recommendations for estimating the amount of debris waste, the experience of various countries that have experienced technological disasters or natural disasters was studied, including Japan, Canada, and countries in the Middle East. The experience of managing debris waste in the communities of Chernihiv, Kyiv, and Mykolaiv regions was also examined. As a result of reviewing international experience, it was determined that the most appropriate approach is to use specific waste generation indicators per unit area – the waste generation rate. It is accepted that the area used to determine the volume of debris waste should be within the boundaries of the destruction or demolition (section, floor, or part of the building). A calculation of the waste generation rate was conducted based on the consumption of primary materials for typical series of multi-apartment residential buildings, monolithic-frame multi-apartment residential buildings, and residential buildings in cottage developments, including buildings of preschool and general secondary education institutions and hospitals.The resulting waste generation rates can be used to estimate the calculated amount of waste generated due to the damage or destruction of residential buildings, buildings of general secondary and preschool education institutions, and healthcare facilities as a result of hostilities, terrorist acts, sabotage, or work to eliminate their consequences. The waste generation rates do not apply to engineering structures, transportation infrastructure, or non-residential buildings.
- Open Access
- 4 February 2025
- Published by Kyiv National University of Construction and Architecture in Construction Engineering
- No. 41,p. 99-107
DETERMINATION OF THE NORMS FOR THE TRANSPORTATION OF MUNICIPAL WASTE FOR VARAS CITY TERRITORIAL COMMUNITY SETTLEMENTS
Solving the problem of municipal waste management is based on determining the amount of generated waste. It is important to conduct research for both urban and rural settlements with different degrees of cov-erage of the population by a centralized system of collection and removal of household waste in order to ob-tain more reliable results.The purpose of the work is to improve methodological approaches to determining the norms of providing services for the transportation of municipal waste in populated areas.Analysis of literature data shows that there is no valid data on field measurements and their results, and there are no consistent forms of presentation of the obtained results. This makes it impossible to com-pare them and carry out a deeper analysis to identify the dependence of the calculated accumulation rates on the population and the level of coverage by the centralized collection system and transportation of municipal waste in cities, territorial communities and villages.This article presents field studies performed to determine the volume of municipal waste generation from the sources of its generation. On-site measurements were carried out on the territory Varas city territori-al community settlements.
- 4 February 2025
- Published by Kyiv National University of Construction and Architecture in Construction Engineering
- No. 41,p. 99-107
Open AccessDETERMINATION OF THE NORMS FOR THE TRANSPORTATION OF MUNICIPAL WASTE FOR VARAS CITY TERRITORIAL COMMUNITY SETTLEMENTS
Solving the problem of municipal waste management is based on determining the amount of generated waste. It is important to conduct research for both urban and rural settlements with different degrees of cov-erage of the population by a centralized system of collection and removal of household waste in order to ob-tain more reliable results.The purpose of the work is to improve methodological approaches to determining the norms of providing services for the transportation of municipal waste in populated areas.Analysis of literature data shows that there is no valid data on field measurements and their results, and there are no consistent forms of presentation of the obtained results. This makes it impossible to com-pare them and carry out a deeper analysis to identify the dependence of the calculated accumulation rates on the population and the level of coverage by the centralized collection system and transportation of municipal waste in cities, territorial communities and villages.This article presents field studies performed to determine the volume of municipal waste generation from the sources of its generation. On-site measurements were carried out on the territory Varas city territori-al community settlements.
- Open Access
- 28 June 2024
- Published by Kyiv National University of Construction and Architecture in Environmental safety and natural resources
- Vol. 50 (2)
Improvement of mechanical and biological treatment technologies according to the morphological and fractional composition of household waste
Achieving the goals of reducing the volume of municipal waste disposal by 30% by 2030, as established by the National Waste Management Strategy in Ukraine until 2030, may become feasible following the establishment of municipal waste management infrastructure.The results of the research on the morphological composition of municipal waste are utilized in waste management sector planning, estimating the expected biogas quantity at municipal waste landfills, determining the amount of heat that can be harnessed from the incineration of municipal waste. The research also highlights the impact of waste composition on the completeness and capacity of waste sorting lines and its influence on the cost of construction and maintenance.The material balance exerts the most significant influence on the technical and economic indicators of waste sorting enterprises, including mechanical-biological treatment facilities. Material balance calculations are carried out based on the morphological and fractional composition of municipal waste.This article presents the results of research into the morphological composition of municipal waste generated in the populated areas of the Sumy urban territorial community. Additionally, findings regarding the fractional composition of municipal waste generated in the city of Kyiv are provided. Based on the results of the morphological and fractional composition research, material balances for municipal waste were calculated, using a simplified technological scheme for mechanical-biological treatment as an illustrative example.
- 28 June 2024
- Published by Kyiv National University of Construction and Architecture in Environmental safety and natural resources
- Vol. 50 (2)
Open AccessImprovement of mechanical and biological treatment technologies according to the morphological and fractional composition of household waste
Achieving the goals of reducing the volume of municipal waste disposal by 30% by 2030, as established by the National Waste Management Strategy in Ukraine until 2030, may become feasible following the establishment of municipal waste management infrastructure.The results of the research on the morphological composition of municipal waste are utilized in waste management sector planning, estimating the expected biogas quantity at municipal waste landfills, determining the amount of heat that can be harnessed from the incineration of municipal waste. The research also highlights the impact of waste composition on the completeness and capacity of waste sorting lines and its influence on the cost of construction and maintenance.The material balance exerts the most significant influence on the technical and economic indicators of waste sorting enterprises, including mechanical-biological treatment facilities. Material balance calculations are carried out based on the morphological and fractional composition of municipal waste.This article presents the results of research into the morphological composition of municipal waste generated in the populated areas of the Sumy urban territorial community. Additionally, findings regarding the fractional composition of municipal waste generated in the city of Kyiv are provided. Based on the results of the morphological and fractional composition research, material balances for municipal waste were calculated, using a simplified technological scheme for mechanical-biological treatment as an illustrative example.
- Open Access
- 29 December 2022
- Published by Kyiv National University of Construction and Architecture in Environmental safety and natural resources
- Vol. 44 (4) , 80-90
Determination of the norms for the transportation of household waste for Hirska amalgamated territorial community settlements
Solving the problem of household waste management is based on determining the amount of waste generated. It is important to conduct research for both urban and rural settlements with different degrees of coverage of the population by a centralized system of collection and removal of household waste in order to obtain more reliable results. The purpose of the work is to improve methodological approaches to determining the norms of providing services for the transportation of household waste in populated areas. Analysis of literature data shows that there is no valid data on field measurements and their results, and there are no consistent forms of presentation of the obtained results. This makes it impossible to compare them and carry out a deeper analysis to identify the dependence of the calculated accumulation rates on the population and the level of coverage by the centralized collection system and transportation of household waste in cities, territorial communities and villages. This article presents field studies performed to determine the volume of household waste generation from the sources of its generation. On-site measurements were carried out on the territory of the Hirska Amalgamated Territorial Community.
- 29 December 2022
- Published by Kyiv National University of Construction and Architecture in Environmental safety and natural resources
- Vol. 44 (4) , 80-90
Open AccessDetermination of the norms for the transportation of household waste for Hirska amalgamated territorial community settlements
Solving the problem of household waste management is based on determining the amount of waste generated. It is important to conduct research for both urban and rural settlements with different degrees of coverage of the population by a centralized system of collection and removal of household waste in order to obtain more reliable results. The purpose of the work is to improve methodological approaches to determining the norms of providing services for the transportation of household waste in populated areas. Analysis of literature data shows that there is no valid data on field measurements and their results, and there are no consistent forms of presentation of the obtained results. This makes it impossible to compare them and carry out a deeper analysis to identify the dependence of the calculated accumulation rates on the population and the level of coverage by the centralized collection system and transportation of household waste in cities, territorial communities and villages. This article presents field studies performed to determine the volume of household waste generation from the sources of its generation. On-site measurements were carried out on the territory of the Hirska Amalgamated Territorial Community.
- Open Access
- 29 December 2022
- Published by Kyiv National University of Construction and Architecture in Environmental safety and natural resources
- Vol. 44 (4) , 53-71
Overview of the technologies of the collection, transportation, recovery and disposal of municipal solid waste
Вирішення проблеми відсутності дієвих технологій відновлення твердих побутових відходів полягає насамперед у побудові ефективної технологічної схеми збирання, перевезення, відновлення та видалення побутових відходів. Досягання цілей зі зменшення обсягу захоронення побутових відходів до 30% у 2030 році, які встановлені Національною стратегією управління відходами в Україні до 2030 року, можливо при застосуванні в населених пунктах, територіальних громадах взаємоузгоджених технологічних етапів зі збирання, перевезення, відновлення та видалення побутових відходів. Дослідження спрямовані на організацію ефективного та уніфікованого управління потоками ТПВ, їх належного зберігання, збирання, транспортування, оброблення, видалення, враховуючи ресурсний потенціал ТПВ, необхідність та доцільність впровадження певної технології оброблення, відновлення та видалення відходів з урахуванням її характеристик і обмежень застосування та необхідність мінімізації навантаження на довкілля, пов’язаного з відходами. Призначення та завдання даної публікації – це опис повного технологічного циклу управління відходами та встановлення послідовності уніфікованих методичних підходів до етапів та технологічних процесів управління твердими побутовими відходами (збирання, перевезення, відновлення та видалення).
- 29 December 2022
- Published by Kyiv National University of Construction and Architecture in Environmental safety and natural resources
- Vol. 44 (4) , 53-71
Open AccessOverview of the technologies of the collection, transportation, recovery and disposal of municipal solid waste
Вирішення проблеми відсутності дієвих технологій відновлення твердих побутових відходів полягає насамперед у побудові ефективної технологічної схеми збирання, перевезення, відновлення та видалення побутових відходів. Досягання цілей зі зменшення обсягу захоронення побутових відходів до 30% у 2030 році, які встановлені Національною стратегією управління відходами в Україні до 2030 року, можливо при застосуванні в населених пунктах, територіальних громадах взаємоузгоджених технологічних етапів зі збирання, перевезення, відновлення та видалення побутових відходів. Дослідження спрямовані на організацію ефективного та уніфікованого управління потоками ТПВ, їх належного зберігання, збирання, транспортування, оброблення, видалення, враховуючи ресурсний потенціал ТПВ, необхідність та доцільність впровадження певної технології оброблення, відновлення та видалення відходів з урахуванням її характеристик і обмежень застосування та необхідність мінімізації навантаження на довкілля, пов’язаного з відходами. Призначення та завдання даної публікації – це опис повного технологічного циклу управління відходами та встановлення послідовності уніфікованих методичних підходів до етапів та технологічних процесів управління твердими побутовими відходами (збирання, перевезення, відновлення та видалення).
- Open Access
- 9 June 2022
- Published by Kyiv National University of Construction and Architecture in Problems of Water supply, Sewerage and Hydraulic
- No. 39,p. 33-43
Increasing corrosion and mechanical resistance destruction of welding cover capacities water towers
В роботі розглянуто стандартні методи визначення корозійно-механічних характеристик працездатності труб і їх зварних з’єднань, сталевих оболонкових конструкцій з постачання води споживачам. Встановлено, що різкі коливання значень мікротвердості в зоні термічного впливу зварного з’єднання перевищують базові значення як в середній частині зварювального шва, так і основного металу труби. Отримані результати можуть бути використані для перевірки службових характеристик корпусних вуглецевих сталей, призначених для будівництва водонапірних башт тривалого терміну експлуатації в корозійно-агресивних середовищах. Під дією градієнту температури на зовнішніх поверхнях стінок водонапірного баку виникають розтягувальні напруження, а на внутрішніх поверхнях – стискувальні, що виявляється сприятливим чинником, який зменшує небезпеку корозійного руйнування. Температурні напруження, які виникають у випадку неоднорідності температури по контуру циліндричного баку, несприятливі. Напруження від вагового навантаження малі і не здійснюють помітного впливу на руйнування сталевого баку, оскільки є стискувальними. Величину технологічних остаточних напружень визначали експериментально механічним тензометруванням згідно класичної методики, а також за допомогою електричних тензодатчиків і ультразвуковим методом по методиці Інституту електрозварювання ім. Є. О. Патона НАНУ. Встановлено експериментальним шляхом, що найбільш небезпечні остаточні зварювальні напруження в монтажних швах, величина яких для поздовжнього компонента напружень близька чи перевищує межу текучості , а для поперечного – близька до межі текучості , в той час як на пластинах із сталі ВСт3 цієї ж товщини . Ймовірно, зварювання при монтажі в умовах жорсткого стиснення металу спричиняє підвищений рівень остаточних напружень. Величина і знак залишкових напружень суттєво залежить від методу монтажу. Навіть при блочному монтажу, коли водонапірна башта монтується з декількох попередньо відпалених блоків, з’єднанням між собою монтажними кільцевими швами на окремих ділянках основного металу поблизу цих швів при підгонці виникають значні напруження (до 17,6 кгс/мм2), на окремих ділянках – до 6 кгс/мм2. При по листовому складанні напруження можуть досягти рівня близького до межі текучості.
- 9 June 2022
- Published by Kyiv National University of Construction and Architecture in Problems of Water supply, Sewerage and Hydraulic
- No. 39,p. 33-43
Open AccessIncreasing corrosion and mechanical resistance destruction of welding cover capacities water towers
В роботі розглянуто стандартні методи визначення корозійно-механічних характеристик працездатності труб і їх зварних з’єднань, сталевих оболонкових конструкцій з постачання води споживачам. Встановлено, що різкі коливання значень мікротвердості в зоні термічного впливу зварного з’єднання перевищують базові значення як в середній частині зварювального шва, так і основного металу труби. Отримані результати можуть бути використані для перевірки службових характеристик корпусних вуглецевих сталей, призначених для будівництва водонапірних башт тривалого терміну експлуатації в корозійно-агресивних середовищах. Під дією градієнту температури на зовнішніх поверхнях стінок водонапірного баку виникають розтягувальні напруження, а на внутрішніх поверхнях – стискувальні, що виявляється сприятливим чинником, який зменшує небезпеку корозійного руйнування. Температурні напруження, які виникають у випадку неоднорідності температури по контуру циліндричного баку, несприятливі. Напруження від вагового навантаження малі і не здійснюють помітного впливу на руйнування сталевого баку, оскільки є стискувальними. Величину технологічних остаточних напружень визначали експериментально механічним тензометруванням згідно класичної методики, а також за допомогою електричних тензодатчиків і ультразвуковим методом по методиці Інституту електрозварювання ім. Є. О. Патона НАНУ. Встановлено експериментальним шляхом, що найбільш небезпечні остаточні зварювальні напруження в монтажних швах, величина яких для поздовжнього компонента напружень близька чи перевищує межу текучості , а для поперечного – близька до межі текучості , в той час як на пластинах із сталі ВСт3 цієї ж товщини . Ймовірно, зварювання при монтажі в умовах жорсткого стиснення металу спричиняє підвищений рівень остаточних напружень. Величина і знак залишкових напружень суттєво залежить від методу монтажу. Навіть при блочному монтажу, коли водонапірна башта монтується з декількох попередньо відпалених блоків, з’єднанням між собою монтажними кільцевими швами на окремих ділянках основного металу поблизу цих швів при підгонці виникають значні напруження (до 17,6 кгс/мм2), на окремих ділянках – до 6 кгс/мм2. При по листовому складанні напруження можуть досягти рівня близького до межі текучості.
- Open Access
- 24 December 2021
- Published by Kyiv National University of Construction and Architecture in Environmental safety and natural resources
- Vol. 40 (4) , 110-120
Improving the methodology for analyses of the morphological composition of municipal solid waste with stratification approach
First, problem-solving for solid waste management should be based on solid field analysis of their morphological composition. It is important to conduct research for both urban and rural settlements to obtain results that are more reliable. The aim of this article is to improve methodological approaches to determining the morphological composition of solid waste. From the data analysis, it is established that the lack of morphological composition of solid waste in the methodology of research requirements for representativeness of research results, error rate and common approaches to the research plan leads to the inability to compare the results of such studies and reduces their value. This study presents a new approach to determining the morphological composition of solid waste. The process of field research of morphological composition in Sumy city took place in 4 stages – preliminary research, sampling planning, field research, evaluation of results. Obtained results show the importance of using the requirements for statistical reliability of results. The application of such an approach allows us to unify the results of the study, and to compare the individual results of determining the morphological composition between settlements and by years.
- 24 December 2021
- Published by Kyiv National University of Construction and Architecture in Environmental safety and natural resources
- Vol. 40 (4) , 110-120
Open AccessImproving the methodology for analyses of the morphological composition of municipal solid waste with stratification approach
First, problem-solving for solid waste management should be based on solid field analysis of their morphological composition. It is important to conduct research for both urban and rural settlements to obtain results that are more reliable. The aim of this article is to improve methodological approaches to determining the morphological composition of solid waste. From the data analysis, it is established that the lack of morphological composition of solid waste in the methodology of research requirements for representativeness of research results, error rate and common approaches to the research plan leads to the inability to compare the results of such studies and reduces their value. This study presents a new approach to determining the morphological composition of solid waste. The process of field research of morphological composition in Sumy city took place in 4 stages – preliminary research, sampling planning, field research, evaluation of results. Obtained results show the importance of using the requirements for statistical reliability of results. The application of such an approach allows us to unify the results of the study, and to compare the individual results of determining the morphological composition between settlements and by years.
- Open Access
- 12 December 2021
- Published by Kyiv National University of Construction and Architecture in Problems of Water supply, Sewerage and Hydraulic
- No. 37,p. 47-56
CARBONIZATION OF CONCRETE AND CORROSION OF REINFORCEMENT OF REINFORCED CONCRETE STRUCTURES OF UNDERGROUND SEWERAGE SYSTEMS
The process of carbonization of concrete with different ratio of water to cement (W/C) was studied, and the influence of the environment on corrosion damage of reinforced concrete reinforcement was studied. The results of the study of carbonization of concrete on specially prepared model samples of concrete with a size of 250x250x250 mm with an exposure period in NACE solution for 500 days without external load are presented. Measurements of corrosion damage of reinforcing rods, which were placed inside concrete cubes, were performed. The method of estimating the amount of carbonization of concrete and corrosion of reinforcement is described in detail in known scientific papers. The obtained data testify to the active carbonization of concrete during the whole exposure period of the samples in NACE solution, however, concrete prepared at the ratio W/C = 0.5 and 0.6 is particularly significant in terms of carbonization intensity. Concrete with a ratio of W/C = 0.7 is less susceptible to damage. Moreover, a similar trend is observed for corrosion of fittings. This is due to the fact that the increase of the aqueous medium in the concrete mass facilitates diffusion processes of delivery to the reactive zone of chemically aggressive ingredients such as carbon dioxide, chloride ions, hydrogen, sulfur, sulfate ions, various types of bacteria and the like. The kinetics of concrete carbonization and corrosion of reinforcing bars in chemically aggressive NACE medium depending on the exposure period of the samples in the model solution was experimentally studied. It is established that with the increase of the water-cement ratio W/C from 0.5 to 0.7, the depth of carbonization and the layer thickness of corrosion products increase sharply. The flooding of the surface layers of the reinforcement and their strong embrittlement in the process of long-term operation of the reinforcement in the structure of reinforced concrete, which causes a decrease in crack resistance in general of reinforced concrete structures. The degradation of reinforcing steel during long-term operation in aggressive environments, which leads to premature corrosion damage to the reinforcement with subsequent destruction of the structure, was investigated experimentally with the involvement of high-precision metallographic equipment.
- 12 December 2021
- Published by Kyiv National University of Construction and Architecture in Problems of Water supply, Sewerage and Hydraulic
- No. 37,p. 47-56
Open AccessCARBONIZATION OF CONCRETE AND CORROSION OF REINFORCEMENT OF REINFORCED CONCRETE STRUCTURES OF UNDERGROUND SEWERAGE SYSTEMS
The process of carbonization of concrete with different ratio of water to cement (W/C) was studied, and the influence of the environment on corrosion damage of reinforced concrete reinforcement was studied. The results of the study of carbonization of concrete on specially prepared model samples of concrete with a size of 250x250x250 mm with an exposure period in NACE solution for 500 days without external load are presented. Measurements of corrosion damage of reinforcing rods, which were placed inside concrete cubes, were performed. The method of estimating the amount of carbonization of concrete and corrosion of reinforcement is described in detail in known scientific papers. The obtained data testify to the active carbonization of concrete during the whole exposure period of the samples in NACE solution, however, concrete prepared at the ratio W/C = 0.5 and 0.6 is particularly significant in terms of carbonization intensity. Concrete with a ratio of W/C = 0.7 is less susceptible to damage. Moreover, a similar trend is observed for corrosion of fittings. This is due to the fact that the increase of the aqueous medium in the concrete mass facilitates diffusion processes of delivery to the reactive zone of chemically aggressive ingredients such as carbon dioxide, chloride ions, hydrogen, sulfur, sulfate ions, various types of bacteria and the like. The kinetics of concrete carbonization and corrosion of reinforcing bars in chemically aggressive NACE medium depending on the exposure period of the samples in the model solution was experimentally studied. It is established that with the increase of the water-cement ratio W/C from 0.5 to 0.7, the depth of carbonization and the layer thickness of corrosion products increase sharply. The flooding of the surface layers of the reinforcement and their strong embrittlement in the process of long-term operation of the reinforcement in the structure of reinforced concrete, which causes a decrease in crack resistance in general of reinforced concrete structures. The degradation of reinforcing steel during long-term operation in aggressive environments, which leads to premature corrosion damage to the reinforcement with subsequent destruction of the structure, was investigated experimentally with the involvement of high-precision metallographic equipment.
- Open Access
- 5 July 2018
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Research Bulletin of the National Technical University of Ukraine "Kyiv Politechnic Institute"
- No. 3,p. 15-22
Influence of Aeration on the Composition of Biocenosis and Efficiency of Removal of Nitrogen-Containing Compounds on Rapid Filters for Drinking Water Treatment
Background. Nitrogen compounds are the most common components of groundwater in Ukraine. Nitrates for humans are not poisonous, but in the human body, they turn into nitrites, affecting the health of the whole organism. One of the possible ways to reduce the content of nitrogen compounds is the use of biotechnological treatment methods, which are not yet widely used in water treatment plants in Ukraine. Objective. The aim of the paper is to study the influence of oxygen on the biocenosis of rapid filters for the drinking water treatment and the efficiency of removing nitrogen-containing compounds. Methods. To assess the influence of aeration on the biocenosis of rapid filters for drinking water treatment, the total microbial number in the upper and lower parts of the filter was measured at different doses of oxygen that was fed to the filter. Results. The experiments show that depending on the different concentration of dissolved oxygen on rapid filters for drinking water treatment, the simultaneous passage of nitrification and denitrification is possible. It is established that with an increase in oxygen concentration up to 7 mg/dm3, the intensity of ammonium removal doesn’t increase, but the value of the CFU in the lower part of the filter decreases (up to 3000 CFU/cm3). The concentration of oxygen in the aerator for ammonia removal is 7 mg/dm3 (ammonium concentration in water after filtration is 0.11 mg/dm3); nitrites – 7.5 mg/dm3 (0.27 mg/dm3 nitrites in water after filtration); nitrates – 5.5 mg/dm3 (2.4 mg/dm3 of nitrates in water after filtration). Conclusions. It is determined that under conditions of rapid filters, nitrification predominantly occurs in the upper part of the filter, and denitrification in the lower part. The optimum concentration of oxygen fed to the filter was established for the simultaneous passage of nitrification and denitrification, and the effective removal of nitrogen compounds in the preparation of drinking water. The concentration should be 5.5 mg/dm3.
- 5 July 2018
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Research Bulletin of the National Technical University of Ukraine "Kyiv Politechnic Institute"
- No. 3,p. 15-22
Open AccessInfluence of Aeration on the Composition of Biocenosis and Efficiency of Removal of Nitrogen-Containing Compounds on Rapid Filters for Drinking Water Treatment
Background. Nitrogen compounds are the most common components of groundwater in Ukraine. Nitrates for humans are not poisonous, but in the human body, they turn into nitrites, affecting the health of the whole organism. One of the possible ways to reduce the content of nitrogen compounds is the use of biotechnological treatment methods, which are not yet widely used in water treatment plants in Ukraine. Objective. The aim of the paper is to study the influence of oxygen on the biocenosis of rapid filters for the drinking water treatment and the efficiency of removing nitrogen-containing compounds. Methods. To assess the influence of aeration on the biocenosis of rapid filters for drinking water treatment, the total microbial number in the upper and lower parts of the filter was measured at different doses of oxygen that was fed to the filter. Results. The experiments show that depending on the different concentration of dissolved oxygen on rapid filters for drinking water treatment, the simultaneous passage of nitrification and denitrification is possible. It is established that with an increase in oxygen concentration up to 7 mg/dm3, the intensity of ammonium removal doesn’t increase, but the value of the CFU in the lower part of the filter decreases (up to 3000 CFU/cm3). The concentration of oxygen in the aerator for ammonia removal is 7 mg/dm3 (ammonium concentration in water after filtration is 0.11 mg/dm3); nitrites – 7.5 mg/dm3 (0.27 mg/dm3 nitrites in water after filtration); nitrates – 5.5 mg/dm3 (2.4 mg/dm3 of nitrates in water after filtration). Conclusions. It is determined that under conditions of rapid filters, nitrification predominantly occurs in the upper part of the filter, and denitrification in the lower part. The optimum concentration of oxygen fed to the filter was established for the simultaneous passage of nitrification and denitrification, and the effective removal of nitrogen compounds in the preparation of drinking water. The concentration should be 5.5 mg/dm3.
- Open Access
- 25 June 2018
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Innovative Biosystems and Bioengineering
- Vol. 2 (2) , 90-97
Bionformation Detection of Magnetic Nanoparticles Producers Among Iron- and Manganese-Oxidizing Bacteria
Background. In Ukraine, more than 17 % of underground water intakes are classified as unfunded in terms of iron content and 4.4 % in terms of manganese content. The increased content of these elements leads to a deterioration in the organoleptic properties of drinking water, the formation of precipitation and overgrowing of the water supply networks due to the development of iron-oxidizing bacteria. Therefore, it is important to study the magnetic properties of iron- and manganese-oxidizing bacteria for the possibility of their use in magnetic separation technologies in order to improve water treatment technologies with excess iron and manganese content. Objective. The aim of the paper is to search for potential producers of BMN among iron- and manganese-oxidizing bacteria and classify them by an internal structure (crystalline or amorphous) and BMN allocation (extracellular or intracellular), using comparative genomics methods. Methods. To evaluate the degree of similarity of BMN biomineralization proteins in MTB Magnetospirillum gryphiswaldense MSR-1 and in iron- and manganese-oxidizing bacteria, pair and multiple alignment methods using the free access program BLAST of the National Center for Biotechnological Information were used. Results. The bioinformatic analysis showed that among the 30 investigated iron- and manganese-oxidizing bacteria which belong to 5 genera (Gallionella, Siderocapsa, Sphaerotilus, Hyphomicrobium, Leptothrix), 28 microorganisms are potential producers of BMN. Conclusions. Conclusions are made about the prospects of further investigation of the influence of the magnetic field on the microorganisms of genera: Leptotrix, Sphaerotillus, Gallionella, Hyphomicrobium. An important direction for further experiments is the study of possible ways of conducting magnetic separation of iron- and manganese-oxidizing bacteria to prevent secondary contamination of drinking water and the formation of scales in pipelines. The use of the magnetic properties of the investigated microorganisms is useful for the development of ways to remove old scales within pipelines.
- 25 June 2018
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Innovative Biosystems and Bioengineering
- Vol. 2 (2) , 90-97
Open AccessBionformation Detection of Magnetic Nanoparticles Producers Among Iron- and Manganese-Oxidizing Bacteria
Background. In Ukraine, more than 17 % of underground water intakes are classified as unfunded in terms of iron content and 4.4 % in terms of manganese content. The increased content of these elements leads to a deterioration in the organoleptic properties of drinking water, the formation of precipitation and overgrowing of the water supply networks due to the development of iron-oxidizing bacteria. Therefore, it is important to study the magnetic properties of iron- and manganese-oxidizing bacteria for the possibility of their use in magnetic separation technologies in order to improve water treatment technologies with excess iron and manganese content. Objective. The aim of the paper is to search for potential producers of BMN among iron- and manganese-oxidizing bacteria and classify them by an internal structure (crystalline or amorphous) and BMN allocation (extracellular or intracellular), using comparative genomics methods. Methods. To evaluate the degree of similarity of BMN biomineralization proteins in MTB Magnetospirillum gryphiswaldense MSR-1 and in iron- and manganese-oxidizing bacteria, pair and multiple alignment methods using the free access program BLAST of the National Center for Biotechnological Information were used. Results. The bioinformatic analysis showed that among the 30 investigated iron- and manganese-oxidizing bacteria which belong to 5 genera (Gallionella, Siderocapsa, Sphaerotilus, Hyphomicrobium, Leptothrix), 28 microorganisms are potential producers of BMN. Conclusions. Conclusions are made about the prospects of further investigation of the influence of the magnetic field on the microorganisms of genera: Leptotrix, Sphaerotillus, Gallionella, Hyphomicrobium. An important direction for further experiments is the study of possible ways of conducting magnetic separation of iron- and manganese-oxidizing bacteria to prevent secondary contamination of drinking water and the formation of scales in pipelines. The use of the magnetic properties of the investigated microorganisms is useful for the development of ways to remove old scales within pipelines.