Assad Alam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Assad Alam has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Ather Gattami
3 shared publications- Jonas Mårtensson
Division of Decision and Control Systems, KTH Royal Institute of Technology, Stockholm, Sweden
2 shared publications - Karl Henrik Johansson
KTH Royal Institute of Technology
2 shared publications Claire J. Tomlin
1 shared publicationDennis Sundman
Commun. Theor. Lab., KTH R. Inst. of Technol., Stockholm, Sweden
1 shared publicationHenrik Pettersson
R&D Dept., Scania CV AB, Sodertalje, Sweden
1 shared publication
Latest Publications
- 1 May 2015
- Published by Elsevier in Control Engineering Practice
- Vol. 38, 11-25
Experimental evaluation of decentralized cooperative cruise control for heavy-duty vehicle platooning
- 1 May 2015
- Published by Elsevier in Control Engineering Practice
- Vol. 38, 11-25
Experimental evaluation of decentralized cooperative cruise control for heavy-duty vehicle platooning
- 1 March 2014
- Published by Elsevier in Control Engineering Practice
- Vol. 24, 33-41
Guaranteeing safety for heavy duty vehicle platooning: Safe set computations and experimental evaluations
- 1 March 2014
- Published by Elsevier in Control Engineering Practice
- Vol. 24, 33-41
Guaranteeing safety for heavy duty vehicle platooning: Safe set computations and experimental evaluations
- 10 July 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Intelligent Transportation Systems
- Vol. 13 (3) , 1033-1049
The Development of a Cooperative Heavy-Duty Vehicle for the GCDC 2011: Team Scoop
The first edition of the Grand Cooperative Driving Challenge (GCDC) was held in the Netherlands in May 2011. Nine international teams competed in urban and highway platooning scenarios with prototype vehicles using cooperative adaptive cruise control. Team Scoop, a collaboration between KTH Royal Institute of Technology, Stockholm, Sweden, and Scania CV AB, Södertälje, Sweden, participated at the GCDC with a Scania R-series tractor unit. This paper describes the development and design of Team Scoop's prototype system for the GCDC. In particular, we present considerations with regard to the system architecture, state estimation and sensor fusion, and the design and implementation of control algorithms, as well as implementation issues with regard to the wireless communication. The purpose of the paper is to give a broad overview of the different components that are needed to develop a cooperative driving system: from architectural design, workflow, and functional requirement descriptions to the specific implementation of algorithms for state estimation and control. The approach is more pragmatic than scientific; it collects a number of existing technologies and gives an implementation-oriented view of a cooperative vehicle. The main conclusion is that it is possible, with a modest effort, to design and implement a system that can function well in cooperation with other vehicles in realistic traffic scenarios.
- 10 July 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Intelligent Transportation Systems
- Vol. 13 (3) , 1033-1049
The Development of a Cooperative Heavy-Duty Vehicle for the GCDC 2011: Team Scoop
The first edition of the Grand Cooperative Driving Challenge (GCDC) was held in the Netherlands in May 2011. Nine international teams competed in urban and highway platooning scenarios with prototype vehicles using cooperative adaptive cruise control. Team Scoop, a collaboration between KTH Royal Institute of Technology, Stockholm, Sweden, and Scania CV AB, Södertälje, Sweden, participated at the GCDC with a Scania R-series tractor unit. This paper describes the development and design of Team Scoop's prototype system for the GCDC. In particular, we present considerations with regard to the system architecture, state estimation and sensor fusion, and the design and implementation of control algorithms, as well as implementation issues with regard to the wireless communication. The purpose of the paper is to give a broad overview of the different components that are needed to develop a cooperative driving system: from architectural design, workflow, and functional requirement descriptions to the specific implementation of algorithms for state estimation and control. The approach is more pragmatic than scientific; it collects a number of existing technologies and gives an implementation-oriented view of a cooperative vehicle. The main conclusion is that it is possible, with a modest effort, to design and implement a system that can function well in cooperation with other vehicles in realistic traffic scenarios.
- 1 November 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21579857,p. 291-297
The impact of heterogeneity and order in heavy duty vehicle platooning networks (poster)
It is formally known that by establishing a heavy duty vehicle platoon, the fuel consumption is reduced for the follower vehicle due to the lower air drag. However, it is not clear how the platoon should be formed with respect to the heavy duty vehicle properties. String stability is a well discussed issue in vehicle platooning. However, each vehicle's properties have to be taken into consideration when analyzing the platoon system. In this paper, we analyze one property of heavy duty vehicles - the mass. The results show that the robustness is influenced by the order and physical characteristics of the vehicles in the platoon. When utilizing identical PID controllers for all vehicles in the platoon, it is better to arrange the heaviest vehicle first with decreasing mass order when considering the platoon behavior. However, in reality it is difficult to start rearranging a platoon in the middle of a highway and it would also require V2V-communication. A controller is often optimized for a particular configuration set that can cause slinky effects to the platoon. Therefore, a mass-dependent PID controller is introduced to establish a better platoon behavior for heavy duty vehicles. The results show no slinky effects regardless of the vehicle order in the platoon.
- 1 November 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21579857,p. 291-297
The impact of heterogeneity and order in heavy duty vehicle platooning networks (poster)
It is formally known that by establishing a heavy duty vehicle platoon, the fuel consumption is reduced for the follower vehicle due to the lower air drag. However, it is not clear how the platoon should be formed with respect to the heavy duty vehicle properties. String stability is a well discussed issue in vehicle platooning. However, each vehicle's properties have to be taken into consideration when analyzing the platoon system. In this paper, we analyze one property of heavy duty vehicles - the mass. The results show that the robustness is influenced by the order and physical characteristics of the vehicles in the platoon. When utilizing identical PID controllers for all vehicles in the platoon, it is better to arrange the heaviest vehicle first with decreasing mass order when considering the platoon behavior. However, in reality it is difficult to start rearranging a platoon in the middle of a highway and it would also require V2V-communication. A controller is often optimized for a particular configuration set that can cause slinky effects to the platoon. Therefore, a mass-dependent PID controller is introduced to establish a better platoon behavior for heavy duty vehicles. The results show no slinky effects regardless of the vehicle order in the platoon.
- 1 September 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21530009,p. 306-311
An experimental study on the fuel reduction potential of heavy duty vehicle platooning
Vehicle platooning has become important for the vehicle industry. Yet conclusive results with respect to the fuel reduction possibilities of platooning remain unclear. The focus in this study is the fuel reduction that heavy duty vehicle platooning enables and the analysis with respect to the influence of a commercial adaptive cruise control on the fuel consumption. Experimental results show that by using preview information of the road ahead from the lead vehicle, the adaptive cruise controller can reduce the fuel consumption. A study is undertaken for various masses of the lead vehicle. The results show that the best choice with respect to a heavier or lighter lead vehicle depends on the desired time gap. A maximum fuel reduction of 4.7-7.7% depending on the time gap, at a set speed of 70 km/h, can be obtained with two identical trucks. If the lead vehicle is 10 t lighter a corresponding 3.8-7.4% fuel reduction can be obtained depending on the time gap. Similarly if the lead vehicle is 10 t heavier a 4.3-6.9% fuel reduction can be obtained. All results indicate that a maximum fuel reduction can be achieved at a short relative distance, due to both air drag reduction and suitable control.
- 1 September 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21530009,p. 306-311
An experimental study on the fuel reduction potential of heavy duty vehicle platooning
Vehicle platooning has become important for the vehicle industry. Yet conclusive results with respect to the fuel reduction possibilities of platooning remain unclear. The focus in this study is the fuel reduction that heavy duty vehicle platooning enables and the analysis with respect to the influence of a commercial adaptive cruise control on the fuel consumption. Experimental results show that by using preview information of the road ahead from the lead vehicle, the adaptive cruise controller can reduce the fuel consumption. A study is undertaken for various masses of the lead vehicle. The results show that the best choice with respect to a heavier or lighter lead vehicle depends on the desired time gap. A maximum fuel reduction of 4.7-7.7% depending on the time gap, at a set speed of 70 km/h, can be obtained with two identical trucks. If the lead vehicle is 10 t lighter a corresponding 3.8-7.4% fuel reduction can be obtained depending on the time gap. Similarly if the lead vehicle is 10 t heavier a 4.3-6.9% fuel reduction can be obtained. All results indicate that a maximum fuel reduction can be achieved at a short relative distance, due to both air drag reduction and suitable control.