Kevin L. White
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Kevin L. White has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Hung-Jue Sue
4 shared publications- Hung-Jue Sue
Texas A&M University
3 shared publications Xi Zhang
3 shared publications- Atsushi Takahara
Research Center for Negative Emission Technologies, Kyushu University, Fukuoka, Japan
2 shared publications - Peng Liu
Kunming University of Science and Technology Oxbridge College, Kunming
2 shared publications - Ryohei Ishige
Department of Chemical Science and Engineering, Institute of Science Tokyo, Tokyo 152-8552, Japan
2 shared publications
Latest Publications
- 1 July 2016
- Published by Wiley in Journal of Polymer Science Part B: Polymer Physics
- Vol. 54 (22) , 2275-2283
Effect of molecular weight on microcrystalline structure formation in polymer with perylenediimide side chain
- 1 July 2016
- Published by Wiley in Journal of Polymer Science Part B: Polymer Physics
- Vol. 54 (22) , 2275-2283
Effect of molecular weight on microcrystalline structure formation in polymer with perylenediimide side chain
- 9 January 2013
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 46 (2) , 463-473
Influence of Trace Amount of Well-Dispersed Carbon Nanotubes on Structural Development and Tensile Properties of Polypropylene
- 9 January 2013
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 46 (2) , 463-473
Influence of Trace Amount of Well-Dispersed Carbon Nanotubes on Structural Development and Tensile Properties of Polypropylene
- 18 September 2012
- Published by Wiley in Polymer Engineering & Science
- Vol. 53 (3) , 651-661
Rheological and thermal behaviors of commercial poly(aryletherketone)s
The mechanical properties and thermal stability of several grades of poly(aryletherketone)s (PAEKs) were investigated using thermal, rheological, and dynamic mechanical characterization. Detailed rheological characterization revealed that several grades of poly(etheretherketone) (PEEK) exhibit relaxation behavior characteristic of a long‐chain branched structure. The potentially branched PEEKs showed greater mechanical damping behavior than the linear‐chain PEEKs. The molecular weight dependence on zero‐shear viscosity for several linear‐chain polymers indicates that the PEEKs behave as rigid chains in the melt. Differences in chain structure do not significantly influence dynamic mechanical behavior in the solid state but affect stability at elevated temperatures. The potentially branched PEEKs are most susceptible to oxidation in air, but exhibit much greater stability in nitrogen. Poly(etherketone) is highly susceptible to degradation in both air and nitrogen environments. Implications of this study for development of high‐performance PAEKs are discussed. POLYM. ENG. SCI. 2013. © 2012 Society of Plastics Engineers
- 18 September 2012
- Published by Wiley in Polymer Engineering & Science
- Vol. 53 (3) , 651-661
Rheological and thermal behaviors of commercial poly(aryletherketone)s
The mechanical properties and thermal stability of several grades of poly(aryletherketone)s (PAEKs) were investigated using thermal, rheological, and dynamic mechanical characterization. Detailed rheological characterization revealed that several grades of poly(etheretherketone) (PEEK) exhibit relaxation behavior characteristic of a long‐chain branched structure. The potentially branched PEEKs showed greater mechanical damping behavior than the linear‐chain PEEKs. The molecular weight dependence on zero‐shear viscosity for several linear‐chain polymers indicates that the PEEKs behave as rigid chains in the melt. Differences in chain structure do not significantly influence dynamic mechanical behavior in the solid state but affect stability at elevated temperatures. The potentially branched PEEKs are most susceptible to oxidation in air, but exhibit much greater stability in nitrogen. Poly(etherketone) is highly susceptible to degradation in both air and nitrogen environments. Implications of this study for development of high‐performance PAEKs are discussed. POLYM. ENG. SCI. 2013. © 2012 Society of Plastics Engineers
- 21 June 2011
- Published by Wiley in Polymer Engineering & Science
- Vol. 51 (11) , 2245-2253
Electrical conductivity and fracture behavior of epoxy/polyamide‐12/multiwalled carbon nanotube composites
Untreated multiwalled carbon nanotubes (MWCNTs) were incorporated into a brittle epoxy matrix at 1 wt% by solvent evaporation and showed significant gains in tensile strength, strain at break, and electrical conductivity. However, only fractional improvement in fracture toughness was observed. To improve fracture toughness, 10 μm polyamide‐12 (PA) preformed particles were added at 20 wt% loading. The PA particles were observed to aid in the dispersion of MWCNTs, reducing most of the large MWCNT clusters to submicron sizes. The epoxy/PA/MWCNT ternary composite exhibits an increased electrical percolation threshold, but nearly identical electrical scaling behavior as the epoxy/MWCNT composite. The similarity in percolation parameters suggest conduction occurs by efficient electron transport through MWCNT clusters, rather than pathways composed of individual tubes. The ternary composite also shows significant improvements in strain at break and fracture toughness due to synergistic interaction between filler phases. The usefulness of this ternary composite approach in vacuum‐assisted resin transfer molding for advanced composite applications is discussed. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers
- 21 June 2011
- Published by Wiley in Polymer Engineering & Science
- Vol. 51 (11) , 2245-2253
Electrical conductivity and fracture behavior of epoxy/polyamide‐12/multiwalled carbon nanotube composites
Untreated multiwalled carbon nanotubes (MWCNTs) were incorporated into a brittle epoxy matrix at 1 wt% by solvent evaporation and showed significant gains in tensile strength, strain at break, and electrical conductivity. However, only fractional improvement in fracture toughness was observed. To improve fracture toughness, 10 μm polyamide‐12 (PA) preformed particles were added at 20 wt% loading. The PA particles were observed to aid in the dispersion of MWCNTs, reducing most of the large MWCNT clusters to submicron sizes. The epoxy/PA/MWCNT ternary composite exhibits an increased electrical percolation threshold, but nearly identical electrical scaling behavior as the epoxy/MWCNT composite. The similarity in percolation parameters suggest conduction occurs by efficient electron transport through MWCNT clusters, rather than pathways composed of individual tubes. The ternary composite also shows significant improvements in strain at break and fracture toughness due to synergistic interaction between filler phases. The usefulness of this ternary composite approach in vacuum‐assisted resin transfer molding for advanced composite applications is discussed. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers