Zhilei Zheng
Zhilei Zheng has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Hang Zheng
Associate Professor, School of Environment and Civil Engineering, Dongguan Univ. of Technology, Dongguan, Guangdong 523106, China
2 shared publicationsZhongjing Wang
Tsinghua Univ
2 shared publicationsJianshi Zhao
Associate Professor, Dept. of Hydraulic Engineering, Tsinghua Univ., Beijing 100084, China; Associate Professor, State Key Laboratory of Hydroscience and Engineering, Tsinghua Univ., Beijing 100084, China
1 shared publicationJinlong Liu
Beijing General Municipal Engineering Design and Research Institute Co., Ltd
1 shared publicationJohn Langford
Professor, Dept. of Infrastructure Engineering, Univ. of Melbourne, Melbourne, VIC 3010, Australia
1 shared publicationTeng Zhang
China Renewable Energy Engineering Institute
1 shared publication
Latest Publications
- 1 April 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Irrigation and Drainage Engineering
- Vol. 152 (2)
Process Response Parsing to Improve the Operation of Multistage Irrigation Canals
- 1 April 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Irrigation and Drainage Engineering
- Vol. 152 (2)
Process Response Parsing to Improve the Operation of Multistage Irrigation Canals
- 1 September 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Water Resources Planning and Management
- Vol. 147 (9) , 04021053
Water Supply Reliability of a Joint Rainwater Storage and On-Stream Reservoir System
Rainwater is regarded as an alternative water source for water supply augmentation in metropolitan areas to mitigate rising water stress caused by increasing population and climate change. There exists a knowledge gap in the evaluation of rainwater-harvesting systems to increase urban water supply reliability. This study provides insight into the impacts of developing rainwater-harvesting systems to improve urban water supply reliability by modeling joint water supplies from both decentralized rainwater-harvesting systems and centralized stream reservoirs. The model is then applied to Melbourne, Australia, using two rainfall regimes. The results show that enlarging roof areas and rainwater tanks, especially for new homes, can increase volumetric rainwater supply reliability at the household scale. This not only increases supply for households but also increases water supply reliability of stream reservoirs at the regional scale. An average roof area of and an average tank size of 8–10 KL can harvest enough rainwater in Melbourne to increase reservoir water supply reliability to 90% for current urban water demand during an extended drought. Using these results, efficient sizes for rainwater tanks are determined by analyzing the cost of enlarging a tank compared with its marginal benefit of increasing rainwater supply reliability. Furthermore, the impacts of climate variability and demand seasonality on system performance are explored using storage-reliability-yield curves for rainwater-harvesting systems. These results provide general insights regarding the feasibility of rainwater water supply augmentation constrained by tank size, roof area, rainfall regime, and demand seasonality. The proposed method for coupling a rainwater tank model at the household scale with a reservoir model at the regional scale is transferable to the design of regional rainwater-harvesting strategies in other cities.- 1 September 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Water Resources Planning and Management
- Vol. 147 (9) , 04021053
Water Supply Reliability of a Joint Rainwater Storage and On-Stream Reservoir System
Rainwater is regarded as an alternative water source for water supply augmentation in metropolitan areas to mitigate rising water stress caused by increasing population and climate change. There exists a knowledge gap in the evaluation of rainwater-harvesting systems to increase urban water supply reliability. This study provides insight into the impacts of developing rainwater-harvesting systems to improve urban water supply reliability by modeling joint water supplies from both decentralized rainwater-harvesting systems and centralized stream reservoirs. The model is then applied to Melbourne, Australia, using two rainfall regimes. The results show that enlarging roof areas and rainwater tanks, especially for new homes, can increase volumetric rainwater supply reliability at the household scale. This not only increases supply for households but also increases water supply reliability of stream reservoirs at the regional scale. An average roof area of and an average tank size of 8–10 KL can harvest enough rainwater in Melbourne to increase reservoir water supply reliability to 90% for current urban water demand during an extended drought. Using these results, efficient sizes for rainwater tanks are determined by analyzing the cost of enlarging a tank compared with its marginal benefit of increasing rainwater supply reliability. Furthermore, the impacts of climate variability and demand seasonality on system performance are explored using storage-reliability-yield curves for rainwater-harvesting systems. These results provide general insights regarding the feasibility of rainwater water supply augmentation constrained by tank size, roof area, rainfall regime, and demand seasonality. The proposed method for coupling a rainwater tank model at the household scale with a reservoir model at the regional scale is transferable to the design of regional rainwater-harvesting strategies in other cities.- 1 June 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Irrigation and Drainage Engineering
- Vol. 145 (6)
Constrained Model Predictive Control Algorithm for Cascaded Irrigation Canals
Agricultural irrigation accounts for the largest proportion of freshwater use worldwide, and canal automation potentially improves conveyance efficiency in irrigation canal systems. In this paper, model predictive control (MPC) for a cascaded irrigation canal system was formulated using the integrator-delay model. Magnitude and variation amplitude constraints on input and output imposed on the canal operation were identified along with proposed handling methods, and optimal control actions were achieved by quadratic objective function optimization. The MPC, as well as classical proportional-integral (PI) and centralized linear quadratic (LQ) for comparison, were developed for the Changma South Irrigation District cascaded irrigation canals in Gansu Province (China) and numerically tested via SOBEK software. In contrast to the poor performance of PI and LQ in controlling the studied canal, the results show that MPC can efficiently control the canal system under known demand changes and maintain water levels at control points within the operating range. The control performance improves if normal input and output constraints are incorporated in optimization. However, deadband constraints, which is the minimum variation amplitude of input, cause controlled water levels to oscillate around the reference value and degrade the control performance. In summary, MPC can cope with time delays, coupling effects, and constraints inherent in a cascaded irrigation canals system. Furthermore, it is suggested to evaluate more advanced methods for handling the output and deadband constraints in future studies.
- 1 June 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Irrigation and Drainage Engineering
- Vol. 145 (6)
Constrained Model Predictive Control Algorithm for Cascaded Irrigation Canals
Agricultural irrigation accounts for the largest proportion of freshwater use worldwide, and canal automation potentially improves conveyance efficiency in irrigation canal systems. In this paper, model predictive control (MPC) for a cascaded irrigation canal system was formulated using the integrator-delay model. Magnitude and variation amplitude constraints on input and output imposed on the canal operation were identified along with proposed handling methods, and optimal control actions were achieved by quadratic objective function optimization. The MPC, as well as classical proportional-integral (PI) and centralized linear quadratic (LQ) for comparison, were developed for the Changma South Irrigation District cascaded irrigation canals in Gansu Province (China) and numerically tested via SOBEK software. In contrast to the poor performance of PI and LQ in controlling the studied canal, the results show that MPC can efficiently control the canal system under known demand changes and maintain water levels at control points within the operating range. The control performance improves if normal input and output constraints are incorporated in optimization. However, deadband constraints, which is the minimum variation amplitude of input, cause controlled water levels to oscillate around the reference value and degrade the control performance. In summary, MPC can cope with time delays, coupling effects, and constraints inherent in a cascaded irrigation canals system. Furthermore, it is suggested to evaluate more advanced methods for handling the output and deadband constraints in future studies.