Gerry Byrne
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Gerry Byrne has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Darina B. Murray
Trinity College, Dublin, Ireland
6 shared publications - Tim Persoons
Trinity College Dublin
6 shared publications - Anthony James Robinson
Trinity Coll Dublin, Dept Mech & Mfg Engn, Parsons Bldg, Dublin, Ireland
3 shared publications - Aimee Byrne
Office of the Vice President for Sustainability, Technological University Dublin, Grangegorman Campus, Clock Tower CT101, Grangegorman, D07 XT95 Dublin, Ireland
2 shared publications Ian M. O. Gorman
Trinity College Dublin, Dublin, Ireland
2 shared publications- Anna Ray Davies
Geography, Trinity College Dublin, Ireland
1 shared publication
Latest Publications
- 2 April 2020
- Published by Taylor & Francis in Biofuels
- Vol. 11 (3) , 297-308
Performance characteristics and exhaust gas analysis of a diesel engine using biodiesel fuel blends
This study details an investigation of the performance and emission characteristics of a Ford XLD 418 compression ignition engine fuelled by various biodiesel/standard agricultural diesel blends. Blend ratios of 10, 50 and 75% were tested and compared with baseline tests performed using pure diesel fuel in the same engine and under the same nominal test conditions. All experiments were carried out in a controlled laboratory environment in accordance with the British Standard, International Organization for Standardization (BS ISO) 15550 standard for compression ignition engines. Numerous full engine performance tests and emission analyses were carried out for each blend, and it is concluded that the engine mechanical performance became marginally worse with increased fuel blend ratio levels. In terms of exhaust gas analysis, emission gas levels for NOx showed a definitive increase, whereas others such as CO and HC generally decreased. CO2 did not show a conclusive trend when regarded in the context of the variation associated with the baseline pure diesel tests, although the literature supports that it increases marginally.
- 2 April 2020
- Published by Taylor & Francis in Biofuels
- Vol. 11 (3) , 297-308
Performance characteristics and exhaust gas analysis of a diesel engine using biodiesel fuel blends
This study details an investigation of the performance and emission characteristics of a Ford XLD 418 compression ignition engine fuelled by various biodiesel/standard agricultural diesel blends. Blend ratios of 10, 50 and 75% were tested and compared with baseline tests performed using pure diesel fuel in the same engine and under the same nominal test conditions. All experiments were carried out in a controlled laboratory environment in accordance with the British Standard, International Organization for Standardization (BS ISO) 15550 standard for compression ignition engines. Numerous full engine performance tests and emission analyses were carried out for each blend, and it is concluded that the engine mechanical performance became marginally worse with increased fuel blend ratio levels. In terms of exhaust gas analysis, emission gas levels for NOx showed a definitive increase, whereas others such as CO and HC generally decreased. CO2 did not show a conclusive trend when regarded in the context of the variation associated with the baseline pure diesel tests, although the literature supports that it increases marginally.
- Open Access
- 9 January 2019
- Published by SAGE Publications in Journal of Ocean and Climate: Science, Technology and Impacts
- Vol. 9
Experimental validation of lift and drag forces on an asymmetrical hydrofoil for seafloor anchoring applications
Tidal power can be described as harnessing the kinetic energy of the in and out flows known as tides created by the changing gravitational pull of the moon and the sun on the oceans of the world. As the relative positions of the sun and moon can be accurately predicted, so can the resultant tidal movements, making tidal energy such a valuable resource and an attractive option for renewable power generation. However, the high costs and difficulties associated with the deployment of underwater turbines, which includes anchoring, are prohibitive factors in the widespread utilisation of tidal power technology. Existing turbine fixation methods are primarily based on the use of large gravity anchors or monopole structures to secure the turbine to the seabed. In an effort to reduce size, environmental impact on the seafloor and installation cost, a hydrofoil-based anchor could be considered. The objective of this study is to experimentally test the lift and drag force behaviour of a finite-span hydrofoil with endplates, whose profile was selected based on simplified two-dimensional (2D) numerical simulations using the vortex panel method. A customised lift and drag force measurement system for this prototype hydrofoil was designed, fabricated and calibrated, and subsequently installed and tested in the Dutch Tidal Testing Centre (TTC) in Den Oever, the Netherlands. A series of tests with force and flow velocity measurements are described for different angles-of-attack under realistic tidal flow conditions. Results for the lift and drag coefficients as a function of angle-of-attack are compared to numerical simulation data and revealed that the real-world lift force is predicted well, whereas the drag force is underpredicted by the numerical predictions. These findings provide useful information for the design of anchoring systems based of hydrofoil profiles.
- 9 January 2019
- Published by SAGE Publications in Journal of Ocean and Climate: Science, Technology and Impacts
- Vol. 9
Open AccessExperimental validation of lift and drag forces on an asymmetrical hydrofoil for seafloor anchoring applications
Tidal power can be described as harnessing the kinetic energy of the in and out flows known as tides created by the changing gravitational pull of the moon and the sun on the oceans of the world. As the relative positions of the sun and moon can be accurately predicted, so can the resultant tidal movements, making tidal energy such a valuable resource and an attractive option for renewable power generation. However, the high costs and difficulties associated with the deployment of underwater turbines, which includes anchoring, are prohibitive factors in the widespread utilisation of tidal power technology. Existing turbine fixation methods are primarily based on the use of large gravity anchors or monopole structures to secure the turbine to the seabed. In an effort to reduce size, environmental impact on the seafloor and installation cost, a hydrofoil-based anchor could be considered. The objective of this study is to experimentally test the lift and drag force behaviour of a finite-span hydrofoil with endplates, whose profile was selected based on simplified two-dimensional (2D) numerical simulations using the vortex panel method. A customised lift and drag force measurement system for this prototype hydrofoil was designed, fabricated and calibrated, and subsequently installed and tested in the Dutch Tidal Testing Centre (TTC) in Den Oever, the Netherlands. A series of tests with force and flow velocity measurements are described for different angles-of-attack under realistic tidal flow conditions. Results for the lift and drag coefficients as a function of angle-of-attack are compared to numerical simulation data and revealed that the real-world lift force is predicted well, whereas the drag force is underpredicted by the numerical predictions. These findings provide useful information for the design of anchoring systems based of hydrofoil profiles.
- 1 December 2016
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 79, 175-186
Electrohydrodynamic augmentation of a reflux thermosyphon
- 1 December 2016
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 79, 175-186
Electrohydrodynamic augmentation of a reflux thermosyphon
- 1 October 2016
- Published by Elsevier in Energy and Buildings
- Vol. 130, 420-433
Case studies of cavity and external wall insulation retrofitted under the Irish Home Energy Saving Scheme: Technical analysis and occupant perspectives
- 1 October 2016
- Published by Elsevier in Energy and Buildings
- Vol. 130, 420-433
Case studies of cavity and external wall insulation retrofitted under the Irish Home Energy Saving Scheme: Technical analysis and occupant perspectives
- 1 June 2013
- Published by Elsevier in Energy and Buildings
- Vol. 61, 356-365
Transient and quasi-steady thermal behaviour of a building envelope due to retrofitted cavity wall and ceiling insulation
- 1 June 2013
- Published by Elsevier in Energy and Buildings
- Vol. 61, 356-365
Transient and quasi-steady thermal behaviour of a building envelope due to retrofitted cavity wall and ceiling insulation
- 26 November 2012
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 395
Effect of Thermal Boundary Condition on Heat Dissipation due to Swirling Jet Impingement on a Heated Plate
- 26 November 2012
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 395
Effect of Thermal Boundary Condition on Heat Dissipation due to Swirling Jet Impingement on a Heated Plate
- Open Access
- 1 September 2011
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 54 (25-26) , 5163-5172
Natural convection heat transfer and fluid dynamics for a pair of vertically aligned isothermal horizontal cylinders
- 1 September 2011
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 54 (25-26) , 5163-5172
Open AccessNatural convection heat transfer and fluid dynamics for a pair of vertically aligned isothermal horizontal cylinders
- 1 January 2010
- Published by ASME International
- p. 131-138
Time-Resolved Heat Transfer and Fluid Dynamic Analysis of Natural Convection From Isothermal Horizontal Cylinders
This paper discusses the close coupling between fluid dynamics and local natural convection heat transfer rates from a pair of isothermally heated horizontal cylinders submerged in water. The presence of a second heated cylinder induces heat transfer enhancements of up to 10%, and strong fluctuations in local heat transfer rate. Therefore specific attention is focused on how the local heat transfer characteristics of the upper cylinder are affected by buoyancy induced fluid flow from the lower cylinder. The paper investigates a range of Rayleigh number between 2·106 and 6·106 , and a vertical cylinder spacing between 2D and 4D. Simultaneous local heat flux measurements and flow velocity measurements using particle image velocimetry reveal oscillatory behaviour of the thermal plume, depending on operating conditions. A joint temporal analysis of the data has provided new insights into the governing mechanisms, which enables further optimisation of the heat transfer performance.
- 1 January 2010
- Published by ASME International
- p. 131-138
Time-Resolved Heat Transfer and Fluid Dynamic Analysis of Natural Convection From Isothermal Horizontal Cylinders
This paper discusses the close coupling between fluid dynamics and local natural convection heat transfer rates from a pair of isothermally heated horizontal cylinders submerged in water. The presence of a second heated cylinder induces heat transfer enhancements of up to 10%, and strong fluctuations in local heat transfer rate. Therefore specific attention is focused on how the local heat transfer characteristics of the upper cylinder are affected by buoyancy induced fluid flow from the lower cylinder. The paper investigates a range of Rayleigh number between 2·106 and 6·106 , and a vertical cylinder spacing between 2D and 4D. Simultaneous local heat flux measurements and flow velocity measurements using particle image velocimetry reveal oscillatory behaviour of the thermal plume, depending on operating conditions. A joint temporal analysis of the data has provided new insights into the governing mechanisms, which enables further optimisation of the heat transfer performance.
- 1 January 2009
- Published by ASME International
- p. 1891-1897
Natural Convection From Isothermal Horizontal Cylinders
The research described here is concerned with natural convection from isothermal cylinders, with a particular focus on the interaction between a pair of vertically aligned cylinders. Prime attention was focused on how the local heat transfer characteristics of the upper cylinder are affected due to buoyancy induced fluid flow from the lower cylinder. Tests were performed using internally heated copper cylinders with an outside diameter 30mm and a vertical separation distance between the cylinders ranging from two to three cylinder diameters. Plume interaction between the heated cylinders was investigated within a Rayleigh number range of 2×106 to 6×106. Spectral analysis of the associated heat transfer interaction is presented showing that interaction between the cylinders causes oscillation of the thermal plume. The effect of this oscillation is considered as a possible enhancement mechanism of the heat transfer performance of the upper cylinder.
- 1 January 2009
- Published by ASME International
- p. 1891-1897
Natural Convection From Isothermal Horizontal Cylinders
The research described here is concerned with natural convection from isothermal cylinders, with a particular focus on the interaction between a pair of vertically aligned cylinders. Prime attention was focused on how the local heat transfer characteristics of the upper cylinder are affected due to buoyancy induced fluid flow from the lower cylinder. Tests were performed using internally heated copper cylinders with an outside diameter 30mm and a vertical separation distance between the cylinders ranging from two to three cylinder diameters. Plume interaction between the heated cylinders was investigated within a Rayleigh number range of 2×106 to 6×106. Spectral analysis of the associated heat transfer interaction is presented showing that interaction between the cylinders causes oscillation of the thermal plume. The effect of this oscillation is considered as a possible enhancement mechanism of the heat transfer performance of the upper cylinder.
- Open Access
- 1 January 2009
- Published by ASME International
- p. 1899-1906
Time Averaged and Fluctuating Heat Transfer Measurements in an Atomising Mist Jet Nozzle
Much is already known about the heat transfer characteristics of impinging air jets, and they are widely used in many engineering applications. There currently exist many correlations describing such characteristics. However, the complex internal structure of many nozzles can lead these to produce results which deviate from those predicted by correlations. One such nozzle is currently used in this research group to produce a water mist flow and this paper describes the experimental characteristics of its single phase behaviour.
- 1 January 2009
- Published by ASME International
- p. 1899-1906
Open AccessTime Averaged and Fluctuating Heat Transfer Measurements in an Atomising Mist Jet Nozzle
Much is already known about the heat transfer characteristics of impinging air jets, and they are widely used in many engineering applications. There currently exist many correlations describing such characteristics. However, the complex internal structure of many nozzles can lead these to produce results which deviate from those predicted by correlations. One such nozzle is currently used in this research group to produce a water mist flow and this paper describes the experimental characteristics of its single phase behaviour.