Timothy Dean
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Timothy Dean has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
J. Tulett
4 shared publicationsD. Lane
3 shared publicationsM. Puckett
3 shared publications- Darvin Lane
Schlumberger USA
2 shared publications - J. Christian Dupuis
Département de Géologie et de Génie Géologique, Université Laval, Québec, Canada
2 shared publications J. Quigley
2 shared publications
Latest Publications
- 1 September 2020
- Published by Society of Exploration Geophysicists in The Leading Edge
- Vol. 39 (9) , 639-645
Seismic noise in an urban environment
The results of an experiment aimed at identifying the nature of major noise sources within an urban area are described. We found the strongest noise source to be an irrigation pump located adjacent to the geophones. The noise from the pump had a narrow bandwidth centered at 75 Hz with a duration of 5 minutes every 17 and 34 minutes during the day and night, respectively. Traffic noise was mainly restricted to between 10 and 25 Hz, with its strength decreasing between 9 p.m. and 6 a.m. Passing aircraft resulted in noise between 30 and 200 Hz lasting about 1 minute. Electrical noise was observed at the supply frequency of 50 Hz, although additional noise at 45 Hz also was observed. Given these results we recommended that acquisition within the area should be restricted to late evening or early morning, receiver locations should be selected to avoid strong localized sources of electrical and/or mechanical noise, and any cables associated with the recording system should be as short as possible (although nodal systems are preferable). If nodal systems are deployed for logistical reasons, real-time noise monitoring should be deployed to identify and avoid bursts of high-amplitude, short-duration noise.
- 1 September 2020
- Published by Society of Exploration Geophysicists in The Leading Edge
- Vol. 39 (9) , 639-645
Seismic noise in an urban environment
The results of an experiment aimed at identifying the nature of major noise sources within an urban area are described. We found the strongest noise source to be an irrigation pump located adjacent to the geophones. The noise from the pump had a narrow bandwidth centered at 75 Hz with a duration of 5 minutes every 17 and 34 minutes during the day and night, respectively. Traffic noise was mainly restricted to between 10 and 25 Hz, with its strength decreasing between 9 p.m. and 6 a.m. Passing aircraft resulted in noise between 30 and 200 Hz lasting about 1 minute. Electrical noise was observed at the supply frequency of 50 Hz, although additional noise at 45 Hz also was observed. Given these results we recommended that acquisition within the area should be restricted to late evening or early morning, receiver locations should be selected to avoid strong localized sources of electrical and/or mechanical noise, and any cables associated with the recording system should be as short as possible (although nodal systems are preferable). If nodal systems are deployed for logistical reasons, real-time noise monitoring should be deployed to identify and avoid bursts of high-amplitude, short-duration noise.
- 1 January 2019
- Published by EAGE Publications bv
- p. 1-5
The Effect of Land Seismic Recording System Noise Levels on Survey Productivity
- 1 January 2019
- Published by EAGE Publications bv
- p. 1-5
The Effect of Land Seismic Recording System Noise Levels on Survey Productivity
- 17 August 2017
- Published by Society of Exploration Geophysicists
- Vol. 1, 201-205
The democratization of seismic acquisition
Acquiring seismic data has typically been an expensive pursuit and acquisition systems are typically not easily adaptable to suit different acquisition scenarios. In this paper we detail the manufacture and performance of an easily adaptable, low-cost, seismic acquisition system using widely available open-source electronic components. Data recorded using the system is comparable to that obtained using a far more expensive commercial seismograph. We aim to develop our design into an open-source seismograph that should enable seismic data to be acquired far more cheaply and thus frequently in the future. Presentation Date: Wednesday, September 27, 2017 Start Time: 4:45 PM Location: 371F Presentation Type: ORAL
- 17 August 2017
- Published by Society of Exploration Geophysicists
- Vol. 1, 201-205
The democratization of seismic acquisition
Acquiring seismic data has typically been an expensive pursuit and acquisition systems are typically not easily adaptable to suit different acquisition scenarios. In this paper we detail the manufacture and performance of an easily adaptable, low-cost, seismic acquisition system using widely available open-source electronic components. Data recorded using the system is comparable to that obtained using a far more expensive commercial seismograph. We aim to develop our design into an open-source seismograph that should enable seismic data to be acquired far more cheaply and thus frequently in the future. Presentation Date: Wednesday, September 27, 2017 Start Time: 4:45 PM Location: 371F Presentation Type: ORAL
- 1 August 2016
- Published by Society of Exploration Geophysicists in The Leading Edge
- Vol. 35 (8) , 684-688
The design of optimized broadband vibroseis sweeps
There is currently much work being done to improve the low-frequency content of land vibroseis data. Although techniques exist for designing sweeps that can extend the bandwidth down to as low as 1 Hz, the inclusion of these frequencies comes at considerable cost, either in the time taken to acquire a sweep or in the reduction of the total sweep energy. We describe the limitations on vibrator performance and how those limitations can be overcome using specialized sweep-design techniques. Perhaps more importantly, we describe how such sweeps can be optimized in terms of maximizing their energy content and verifying their performance.
- 1 August 2016
- Published by Society of Exploration Geophysicists in The Leading Edge
- Vol. 35 (8) , 684-688
The design of optimized broadband vibroseis sweeps
There is currently much work being done to improve the low-frequency content of land vibroseis data. Although techniques exist for designing sweeps that can extend the bandwidth down to as low as 1 Hz, the inclusion of these frequencies comes at considerable cost, either in the time taken to acquire a sweep or in the reduction of the total sweep energy. We describe the limitations on vibrator performance and how those limitations can be overcome using specialized sweep-design techniques. Perhaps more importantly, we describe how such sweeps can be optimized in terms of maximizing their energy content and verifying their performance.
- Open Access
- 1 December 2015
- Published by Taylor & Francis in ASEG Extended Abstracts
- Vol. 2015 (1) , 1-4
The impact of tilted geophones on land seismic data quality
The moving coil geophone is still the most commonly used sensor for land seismic surveys despite the introduction of other sensors. Modern geophone development has reached the stage where the signal recorded is of very high quality, but it can still be affected by the geophone being placed on an angle relative to the vertical ('tilt'). This paper describes the acquisition and analysis of field measurements using tilted geophones. It is shown that the critical angle of the 10 Hz geophones used for this test is 55°. For data recorded using vertically placed geophones separated by only 10 cm the perturbation level (the difference between the data recorded by adjacent geophones) averaged 8% and increased to more than 50% at tilt angles of 40º. The level of perturbation is heavily dependent on the orientation of the tilt angle relative to the source-detector axis, for example, for a geophone tilted at an angle of 30°, the perturbation varied between 14% and 48%. The obvious solution to these issues is to record data using sensors that have been planted extremely carefully or to use other sensors, such as digital accelerometers or 3C sensors that have the effect of tilt removed during processing.
- 1 December 2015
- Published by Taylor & Francis in ASEG Extended Abstracts
- Vol. 2015 (1) , 1-4
Open AccessThe impact of tilted geophones on land seismic data quality
The moving coil geophone is still the most commonly used sensor for land seismic surveys despite the introduction of other sensors. Modern geophone development has reached the stage where the signal recorded is of very high quality, but it can still be affected by the geophone being placed on an angle relative to the vertical ('tilt'). This paper describes the acquisition and analysis of field measurements using tilted geophones. It is shown that the critical angle of the 10 Hz geophones used for this test is 55°. For data recorded using vertically placed geophones separated by only 10 cm the perturbation level (the difference between the data recorded by adjacent geophones) averaged 8% and increased to more than 50% at tilt angles of 40º. The level of perturbation is heavily dependent on the orientation of the tilt angle relative to the source-detector axis, for example, for a geophone tilted at an angle of 30°, the perturbation varied between 14% and 48%. The obvious solution to these issues is to record data using sensors that have been planted extremely carefully or to use other sensors, such as digital accelerometers or 3C sensors that have the effect of tilt removed during processing.
- Open Access
- 1 December 2015
- Published by Taylor & Francis in ASEG Extended Abstracts
- Vol. 2015 (1) , 1-4
On the effectiveness of geophone arrays for attenuating ambient noise
Historically, arrays have been used to attenuate ambient noise under the assumption that the level of attenuation is directly proportional to the square root of the number of sensors in the array. Given the availability of high channel-count point-receiver systems and the cost associated with laying out large arrays this assumption of 'spatial randomness' requires further analysis. Using measurements of ambient noise made at various sites in Perth, Australia with closely spaced geophones we show that ambient noise is strongly correlated over distances of up to 10 m. This correlation reduces the signal-to-ambient-noise performance of an array considerably. The correlation coefficient can be modelled using an exponential function and the correlation-distance used to determine the efficient geophone spacing. The optimum geophone spacing on days with a low wind speed ( 80 km/h) the optimum spacing is 2.5 m, although this wind speed is very uncommon, occurring on average less than once each year. For more than 90% of days the wind speed is such that the optimum geophone spacing required for ambient noise suppression is 7.5 m.
- 1 December 2015
- Published by Taylor & Francis in ASEG Extended Abstracts
- Vol. 2015 (1) , 1-4
Open AccessOn the effectiveness of geophone arrays for attenuating ambient noise
Historically, arrays have been used to attenuate ambient noise under the assumption that the level of attenuation is directly proportional to the square root of the number of sensors in the array. Given the availability of high channel-count point-receiver systems and the cost associated with laying out large arrays this assumption of 'spatial randomness' requires further analysis. Using measurements of ambient noise made at various sites in Perth, Australia with closely spaced geophones we show that ambient noise is strongly correlated over distances of up to 10 m. This correlation reduces the signal-to-ambient-noise performance of an array considerably. The correlation coefficient can be modelled using an exponential function and the correlation-distance used to determine the efficient geophone spacing. The optimum geophone spacing on days with a low wind speed ( 80 km/h) the optimum spacing is 2.5 m, although this wind speed is very uncommon, occurring on average less than once each year. For more than 90% of days the wind speed is such that the optimum geophone spacing required for ambient noise suppression is 7.5 m.
- 18 March 2015
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 80 (3) , P1-P10
The coherency of ambient seismic noise recorded during land surveys and the resulting implications for the effectiveness of geophone arrays
The use of analog sensor arrays is often assumed to provide signal-to-ambient-noise improvements proportional to the square root of the number of sensors being summed. We determined via numerical modeling and field experiments that the improvements sought were significantly hindered once the ambient noise exhibited coherence over the array being summed. As a first step, a numerical model was developed to explore the optimal sensor spacing based on the average correlation coefficient between sensors. Field experiments were then carried out to measure ambient noise using closely spaced geophones at several sites in Perth, Western Australia. We show that the measured noise at six test sites was strongly coherent over distances of up to 10 m, with the level of coherency being inversely proportional to frequency. The resulting optimum geophone spacing under our field conditions was determined to be 7.5 m. These results offered further encouragement to reassess our use of analog arrays and to consider recording the output from individual sensors. In addition to the benefits from postacquisition noise suppression, this approach will enable increased trace density without degradation of the signal caused by strong coherent noise sources over acquisition spreads.
- 18 March 2015
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 80 (3) , P1-P10
The coherency of ambient seismic noise recorded during land surveys and the resulting implications for the effectiveness of geophone arrays
The use of analog sensor arrays is often assumed to provide signal-to-ambient-noise improvements proportional to the square root of the number of sensors being summed. We determined via numerical modeling and field experiments that the improvements sought were significantly hindered once the ambient noise exhibited coherence over the array being summed. As a first step, a numerical model was developed to explore the optimal sensor spacing based on the average correlation coefficient between sensors. Field experiments were then carried out to measure ambient noise using closely spaced geophones at several sites in Perth, Western Australia. We show that the measured noise at six test sites was strongly coherent over distances of up to 10 m, with the level of coherency being inversely proportional to frequency. The resulting optimum geophone spacing under our field conditions was determined to be 7.5 m. These results offered further encouragement to reassess our use of analog arrays and to consider recording the output from individual sensors. In addition to the benefits from postacquisition noise suppression, this approach will enable increased trace density without degradation of the signal caused by strong coherent noise sources over acquisition spreads.
- 17 March 2014
- Published by Society of Petroleum Engineers (SPE)
Improving Vertical Seismic Profile Safety Through the Use of Specially Designed Source Vehicles
Two successive models of truck-mounted seismic vibrators were designed and manufactured to ensure the highest possible levels of vehicle safety while also delivering excellent data quality. Seismic vibrators are the preferred energy sources for land vertical seismic profile (VSP) surveys because they are relatively repeatable and controllable, have high energy but a low HSE impact, and are cost effective. Recent advances in vibrator design have enriched the quality of VSP data, but the improvements have been mainly applied only to buggy-mounted vibrators. Buggy-mounted vibrators are typically used for surface seismic surveys in remote areas, and thus their design has been optimized for off-road performance. Surface seismic surveys have typical durations of a number of months or even years. However, VSP surveys are often of short duration (several hours) and require rapid equipment mobilization to the wellsite, often at short notice. Seismic vibrators for vibroseis VSP surveys may spend more time in road transportation to and from the wellsite than in performing the actual VSP survey. While the main HSE safety exposure for buggy-mounted vibrators is related to their off-road use, the main exposure for the vibrators used in VSPs is related to their transport between work sites and their use by sometimes relatively inexperienced personnel (vehicle weights can be more than 30 tons and hydraulic pressures often exceed 3,000 psi). As the targets for VSP surveys become more complex, there is a need to use more advanced vibrators, which until now have only been available as buggy mounted. However, the use of buggy-mounted vibrators for VSP surveys has HSE implications for transportation. To overcome these issues, the special truck-mounted vibrators that have been developed incorporate all the recent improvements in vibrator quality while retaining all the HSE advantages of modern truck-mounted vehicles, such as their ability to be driven safely between wellsites, and additional modifications to ensure the safety of personnel with limited experience. One of the greatest HSE exposure risks associated with vibroseis VSP operations occurs during transportation to and from wellsites. Since the introduction of the new vehicles, there have been no HSE incidents.
- 17 March 2014
- Published by Society of Petroleum Engineers (SPE)
Improving Vertical Seismic Profile Safety Through the Use of Specially Designed Source Vehicles
Two successive models of truck-mounted seismic vibrators were designed and manufactured to ensure the highest possible levels of vehicle safety while also delivering excellent data quality. Seismic vibrators are the preferred energy sources for land vertical seismic profile (VSP) surveys because they are relatively repeatable and controllable, have high energy but a low HSE impact, and are cost effective. Recent advances in vibrator design have enriched the quality of VSP data, but the improvements have been mainly applied only to buggy-mounted vibrators. Buggy-mounted vibrators are typically used for surface seismic surveys in remote areas, and thus their design has been optimized for off-road performance. Surface seismic surveys have typical durations of a number of months or even years. However, VSP surveys are often of short duration (several hours) and require rapid equipment mobilization to the wellsite, often at short notice. Seismic vibrators for vibroseis VSP surveys may spend more time in road transportation to and from the wellsite than in performing the actual VSP survey. While the main HSE safety exposure for buggy-mounted vibrators is related to their off-road use, the main exposure for the vibrators used in VSPs is related to their transport between work sites and their use by sometimes relatively inexperienced personnel (vehicle weights can be more than 30 tons and hydraulic pressures often exceed 3,000 psi). As the targets for VSP surveys become more complex, there is a need to use more advanced vibrators, which until now have only been available as buggy mounted. However, the use of buggy-mounted vibrators for VSP surveys has HSE implications for transportation. To overcome these issues, the special truck-mounted vibrators that have been developed incorporate all the recent improvements in vibrator quality while retaining all the HSE advantages of modern truck-mounted vehicles, such as their ability to be driven safely between wellsites, and additional modifications to ensure the safety of personnel with limited experience. One of the greatest HSE exposure risks associated with vibroseis VSP operations occurs during transportation to and from wellsites. Since the introduction of the new vehicles, there have been no HSE incidents.
- Open Access
- 1 December 2013
- Published by Taylor & Francis in ASEG Extended Abstracts
- Vol. 2013 (1) , 1-4
Significant VSP data quality improvements through the use of a broadband source
Seismic vibrators are the preferred sources for vertical seismic profile (VSP) surveys as they are relatively repeatable, controllable, have high energy, have a low environmental impact and are cost-effective. Unfortunately, due to the mechanical and hydraulic constraints of the vehicles, the typical swept bandwidth has been quite limited, typically of the order of 3 octaves. In this paper show that dramatic improvements in seismic data quality can be achieved by extending the bandwidth used for Vibroseis VSPs. These increases are reliant, however, on the use of modern vibrators, specialised low-frequency enhancing sweeps, and downhole sensors with an extended frequency response range.
- 1 December 2013
- Published by Taylor & Francis in ASEG Extended Abstracts
- Vol. 2013 (1) , 1-4
Open AccessSignificant VSP data quality improvements through the use of a broadband source
Seismic vibrators are the preferred sources for vertical seismic profile (VSP) surveys as they are relatively repeatable, controllable, have high energy, have a low environmental impact and are cost-effective. Unfortunately, due to the mechanical and hydraulic constraints of the vehicles, the typical swept bandwidth has been quite limited, typically of the order of 3 octaves. In this paper show that dramatic improvements in seismic data quality can be achieved by extending the bandwidth used for Vibroseis VSPs. These increases are reliant, however, on the use of modern vibrators, specialised low-frequency enhancing sweeps, and downhole sensors with an extended frequency response range.