Jinhuan Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jinhuan Zhang has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Zhenggui Zhou
College of Energy and Power Engineering , Nanjing University of Aeronautics and Astronautics , Yudao St. 29#, Qinhuai District , Nanjing , Jiangsu Province , People’s Republic of China
2 shared publications Cui Cui
Jiangsu Province Key Laboratory of Aerospace Power Systems, College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics, Jiangsu, PR China
1 shared publicationWenqiang Wei
1 shared publicationYuzhen Deng
1 shared publicationZhenggui Zhou
1 shared publication
Latest Publications
- 3 September 2018
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Vol. 233 (9) , 3426-3444
Aerodynamic optimization design of aspirated highly loaded fan stage
In this paper, an aerodynamic design method for an aspirated compressor/fan is developed. In the S2 through-flow design, the loss feedback is used to solve the inapplicability of the conventional loss model. In S1 profile design, an optimization design method is constructed in which the profile and the suction flow parameters are simultaneously handled as design parameters to couple the optimization design. A 3D optimization method is used to modify the profiles at the hub and tip of the rotor blade and the sweep and lean of the stator blade. An aspirated highly loaded fan stage (load coefficient of 0.69) was designed using the design method. A flow field simulation shows that at the design point, with a modest suction flow (4.84% of the inlet mass flow), very high isentropic efficiency (0.9213) is achieved, and the total pressure ratio (3.445) achieves its design goal (3.40), but the mass flow rate of the designed fan stage is 6.2% lower than the design goal. From the comparisons between the 2D flow fields on the S1 stream surfaces and the 3D flow fields at the corresponding blade spans, it is concluded that the flow presents nearly a form of a 2D S1 stream surface at most of the spans, and the 2D design method which is based on the S1/S2 stream surface in this paper is effective. Moreover, the flow is analyzed around the rotor root of the aspirated rotor, revealing a weak flow capacity in that area. This result suggests that desirable flow might not be set up when the designed profile has a large camber at the rotor blade root because the total pressure ratio cannot be improved without compromising the static pressure ratio.
- 3 September 2018
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Vol. 233 (9) , 3426-3444
Aerodynamic optimization design of aspirated highly loaded fan stage
In this paper, an aerodynamic design method for an aspirated compressor/fan is developed. In the S2 through-flow design, the loss feedback is used to solve the inapplicability of the conventional loss model. In S1 profile design, an optimization design method is constructed in which the profile and the suction flow parameters are simultaneously handled as design parameters to couple the optimization design. A 3D optimization method is used to modify the profiles at the hub and tip of the rotor blade and the sweep and lean of the stator blade. An aspirated highly loaded fan stage (load coefficient of 0.69) was designed using the design method. A flow field simulation shows that at the design point, with a modest suction flow (4.84% of the inlet mass flow), very high isentropic efficiency (0.9213) is achieved, and the total pressure ratio (3.445) achieves its design goal (3.40), but the mass flow rate of the designed fan stage is 6.2% lower than the design goal. From the comparisons between the 2D flow fields on the S1 stream surfaces and the 3D flow fields at the corresponding blade spans, it is concluded that the flow presents nearly a form of a 2D S1 stream surface at most of the spans, and the 2D design method which is based on the S1/S2 stream surface in this paper is effective. Moreover, the flow is analyzed around the rotor root of the aspirated rotor, revealing a weak flow capacity in that area. This result suggests that desirable flow might not be set up when the designed profile has a large camber at the rotor blade root because the total pressure ratio cannot be improved without compromising the static pressure ratio.
- 1 April 2017
- Published by Elsevier in Aerospace Science and Technology
- Vol. 63, 73-81
Aerodynamic design of an ultra-low rotating speed geared fan
- 1 April 2017
- Published by Elsevier in Aerospace Science and Technology
- Vol. 63, 73-81
Aerodynamic design of an ultra-low rotating speed geared fan
- 21 July 2015
- Published by Wiley in International Journal for Numerical Methods in Fluids
- Vol. 79 (12) , 640-653
An improved genetic algorithm and its applications to the optimisation design of an aspirated compressor profile
- 21 July 2015
- Published by Wiley in International Journal for Numerical Methods in Fluids
- Vol. 79 (12) , 640-653
An improved genetic algorithm and its applications to the optimisation design of an aspirated compressor profile