Mamidala Saketh Ram
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Mamidala Saketh Ram has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Lars-Erik Wernersson
Lund University
9 shared publications Dawit Burusie Abdi
4 shared publicationsKarl-Magnus Persson
Department of Electrical and Information Technology, Lund University, Lund, Sweden
3 shared publicationsMattias Borg
Department of Electrical and Information Technology, Lund University, SE-221 00 Lund, Sweden and NanoLund, Lund University 22100 Lund, Sweden
3 shared publications- Karl-Magnus Persson
Technical Research Centre of Finland VTT Ltd. Espoo Finland
2 shared publications Adam Jönsson
Department of Electrical and Information Technology, Lund University, Lund, Sweden
1 shared publication
Latest Publications
- Open Access
- 8 January 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (21)
Interface Characterization of Plasma‐Treated InAs Electrodes for Resistive Random‐Access Memories Using Capacitance–Voltage Methods
InAs nanowires have been used as selectors and electrodes in a one‐transistor one‐resistor resistive random‐access memory (RRAM) configuration for increased memory scalability. Such oxide‐based memories not only show promise both in conventional memory technology but also as analog memories for neural networks. The small areas of the oxide elements, however, result in challenges for electrical characterization of the oxide–semiconductor interface. By analyzing larger test structures, it is possible to perform impedance spectroscopy on the oxide–InAs interface. In this article, HfO 2 ‐based RRAMs on InAs are fabricated using plasma‐enhanced atomic layer deposition. The effect of the plasma‐length is investigated using capacitance–voltage and DC measurements. It is found that an increased plasma‐length results not only in a higher total electron trapping but also in the formation of a more stable interfacial oxide, possibly related to the stoichiometry of the complex InAs oxide. The findings give us a better understanding of the noise‐ and switching‐performance of scaled nanowire devices.
- 8 January 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (21)
Open AccessInterface Characterization of Plasma‐Treated InAs Electrodes for Resistive Random‐Access Memories Using Capacitance–Voltage Methods
InAs nanowires have been used as selectors and electrodes in a one‐transistor one‐resistor resistive random‐access memory (RRAM) configuration for increased memory scalability. Such oxide‐based memories not only show promise both in conventional memory technology but also as analog memories for neural networks. The small areas of the oxide elements, however, result in challenges for electrical characterization of the oxide–semiconductor interface. By analyzing larger test structures, it is possible to perform impedance spectroscopy on the oxide–InAs interface. In this article, HfO 2 ‐based RRAMs on InAs are fabricated using plasma‐enhanced atomic layer deposition. The effect of the plasma‐length is investigated using capacitance–voltage and DC measurements. It is found that an increased plasma‐length results not only in a higher total electron trapping but also in the formation of a more stable interfacial oxide, possibly related to the stoichiometry of the complex InAs oxide. The findings give us a better understanding of the noise‐ and switching‐performance of scaled nanowire devices.
- 8 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (7) , 1212-1215
Self-Heating in Gate-All-Around Vertical III-V InAs/InGaAs MOSFETs
We investigate self-heating in vertical, gate-all-around III-V InAs/InGaAs nanowire MOSFETs using pulsed IV measurements at various temperatures. Low temperature measurements reveal a negative output conductance indicating self-heating in the transistor. Under pulsed measurements, an increase in drain current (15%) and transconductance (30%) are observed at room temperature, with values influenced by the pulse width. This effect on performance is quantified with determination of the thermal resistance and capacitance. Furthermore, a first order thermal circuit is modelled based on the thermal impedances. The results indicate that the intrinsic temperature rises to 385 K when the device is operated in DC at room temperature (300 K) with a thermal time constant of 1 μs. We find that self-heating is a limiting factor for device performance.
- 8 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (7) , 1212-1215
Self-Heating in Gate-All-Around Vertical III-V InAs/InGaAs MOSFETs
We investigate self-heating in vertical, gate-all-around III-V InAs/InGaAs nanowire MOSFETs using pulsed IV measurements at various temperatures. Low temperature measurements reveal a negative output conductance indicating self-heating in the transistor. Under pulsed measurements, an increase in drain current (15%) and transconductance (30%) are observed at room temperature, with values influenced by the pulse width. This effect on performance is quantified with determination of the thermal resistance and capacitance. Furthermore, a first order thermal circuit is modelled based on the thermal impedances. The results indicate that the intrinsic temperature rises to 385 K when the device is operated in DC at room temperature (300 K) with a thermal time constant of 1 μs. We find that self-heating is a limiting factor for device performance.
- Open Access
- 7 April 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (15) , 19085-19091
Effects of Interface Oxidation on Noise Properties and Performance in III–V Vertical Nanowire Memristors
- 7 April 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (15) , 19085-19091
Open AccessEffects of Interface Oxidation on Noise Properties and Performance in III–V Vertical Nanowire Memristors
- 19 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (12) , 2033-2036
Low-Frequency Noise in Vertical InAs/InGaAs Gate-All-Around MOSFETs at 15 K for Cryogenic Applications
Low-frequency noise (LFN), or 1/ f -noise, can be used effectively to evaluate device reliability which is a major concern in analog as well as digital circuits. In this work, we present 1/ f -noise characterization of vertical InAs/InGaAs gate-all-around (GAA) MOSFETs with a 70-nm gate length ( LG ) measured at cryogenic temperatures down to 15 K. The measurements at cryogenic temperatures reveal that the physical mechanism of 1/ f -noise changes from carrier number fluctuations at 300 K to mobility fluctuations at 15 K. We conclude that the channel conduction at 15 K is dominated by the nanowire core instead of the nanowire surface due to the effect of the border and interface traps freezing out. Vertical InAs/InGaAs GAA MOSFETs at 15 K, due to reduced surface scattering, exhibit a low value of Hooge parameter, α H ~ 5 × 10 -6 and also have a low input-referred gate voltage noise spectral density, S VG = 4.3 μV 2 μm 2 Hz -1 that are important for reliable cryogenic circuit applications.
- 19 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (12) , 2033-2036
Low-Frequency Noise in Vertical InAs/InGaAs Gate-All-Around MOSFETs at 15 K for Cryogenic Applications
Low-frequency noise (LFN), or 1/ f -noise, can be used effectively to evaluate device reliability which is a major concern in analog as well as digital circuits. In this work, we present 1/ f -noise characterization of vertical InAs/InGaAs gate-all-around (GAA) MOSFETs with a 70-nm gate length ( LG ) measured at cryogenic temperatures down to 15 K. The measurements at cryogenic temperatures reveal that the physical mechanism of 1/ f -noise changes from carrier number fluctuations at 300 K to mobility fluctuations at 15 K. We conclude that the channel conduction at 15 K is dominated by the nanowire core instead of the nanowire surface due to the effect of the border and interface traps freezing out. Vertical InAs/InGaAs GAA MOSFETs at 15 K, due to reduced surface scattering, exhibit a low value of Hooge parameter, α H ~ 5 × 10 -6 and also have a low input-referred gate voltage noise spectral density, S VG = 4.3 μV 2 μm 2 Hz -1 that are important for reliable cryogenic circuit applications.
- 21 December 2021
- Published by Springer Nature in Nature Electronics
- Vol. 4 (12) , 914-920
High-density logic-in-memory devices using vertical indium arsenide nanowires on silicon
- 21 December 2021
- Published by Springer Nature in Nature Electronics
- Vol. 4 (12) , 914-920
High-density logic-in-memory devices using vertical indium arsenide nanowires on silicon
- Open Access
- 12 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 9, 564-569
Ultra-Scaled AlOx Diffusion Barriers for Multibit HfOx RRAM Operation
For dense very large scale integration (VLSI) of high performance, multibit resistive memory (RRAM), scalability of material dimensions, as well as the operational sensitivity of the RRAM to voltage fluctuations, have to be considered. This report presents the benefits of adding 0.5-nm thick AlO x diffusion barriers at the different electrode interfaces of HfO x . It is found that implementing AlO x -layers at both the bottom and the top electrode interface enables a tight control of the oxygen vacancy filament, resulting in low switching voltages and significantly improving switching endurance up to 10 6 cycles using a performance limiting resistor compliance. It is also shown that the filament in its low resistive state ( R LRS ) can be linearly reduced and enlarged at levels compatible to the conduction limitations of scaled selectors using an external 1T1R transistor compliance. With selector controlled resistance modulation, the R LRS becomes independent of the magnitude of the programming voltage and thus less sensitive to losses throughout a large memory array.
- 12 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 9, 564-569
Open AccessUltra-Scaled AlOx Diffusion Barriers for Multibit HfOx RRAM Operation
For dense very large scale integration (VLSI) of high performance, multibit resistive memory (RRAM), scalability of material dimensions, as well as the operational sensitivity of the RRAM to voltage fluctuations, have to be considered. This report presents the benefits of adding 0.5-nm thick AlO x diffusion barriers at the different electrode interfaces of HfO x . It is found that implementing AlO x -layers at both the bottom and the top electrode interface enables a tight control of the oxygen vacancy filament, resulting in low switching voltages and significantly improving switching endurance up to 10 6 cycles using a performance limiting resistor compliance. It is also shown that the filament in its low resistive state ( R LRS ) can be linearly reduced and enlarged at levels compatible to the conduction limitations of scaled selectors using an external 1T1R transistor compliance. With selector controlled resistance modulation, the R LRS becomes independent of the magnitude of the programming voltage and thus less sensitive to losses throughout a large memory array.
- 3 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 41 (9) , 1432-1435
Low-Power Resistive Memory Integrated on III–V Vertical Nanowire MOSFETs on Silicon
III-V vertical nanowire MOSFETs (VNW-FETs) have the potential to extend Moore’s law owing to their excellent material properties. To integrate highly scaled memory cells coupled with high performance selectors at minimal memory cell area, it is attractive to integrate low-power resistive random access memory (RRAM) cells directly on to III-V VNW-FETs. In this work, we report the experimental demonstration of successful RRAM integration with III-V VNW-FETs. The combined use of VNW-FET drain metal electrode and the RRAM bottom electrode reduces the process complexity and maintains material compatibility. The vertical nanowire geometry allows the RRAM cell area to be aggressively scaled down to 0.01 μm2 enabling realization of dense memory (1T1R) cross-point arrays on silicon.
- 3 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 41 (9) , 1432-1435
Low-Power Resistive Memory Integrated on III–V Vertical Nanowire MOSFETs on Silicon
III-V vertical nanowire MOSFETs (VNW-FETs) have the potential to extend Moore’s law owing to their excellent material properties. To integrate highly scaled memory cells coupled with high performance selectors at minimal memory cell area, it is attractive to integrate low-power resistive random access memory (RRAM) cells directly on to III-V VNW-FETs. In this work, we report the experimental demonstration of successful RRAM integration with III-V VNW-FETs. The combined use of VNW-FET drain metal electrode and the RRAM bottom electrode reduces the process complexity and maintains material compatibility. The vertical nanowire geometry allows the RRAM cell area to be aggressively scaled down to 0.01 μm2 enabling realization of dense memory (1T1R) cross-point arrays on silicon.
- Open Access
- 11 May 2020
- Published by Wiley in Advanced Electronic Materials
- Vol. 6 (6)
Cross‐Point Arrays with Low‐Power ITO‐HfO2 Resistive Memory Cells Integrated on Vertical III‐V Nanowires
Vertical nanowires with cointegrated metal‐oxide‐semiconductor field‐effect‐transistor (MOSFET) selectors and nonvolatile resistive random access memory (RRAM) cells represent a promising candidate for fast, energy‐efficient, cross‐point memory cells. This paper explores indium‐tin‐oxide‐hafnium‐dioxide RRAM cells integrated onto arrays of indium‐arsenide (InAs) vertical nanowires with a resulting area of 0.06 µm2 per cell. For low current operation, an improved switching uniformity over the intrinsic self‐compliant behavior is demonstrated when using an external InAs nanowire MOSFET selector in series. The memory cells show consistent switching voltages below ±1 V and a switching cycle endurance of 106 is demonstrated. The developed fabrication scheme is fully compatible with low‐ON‐resistance vertical III‐V nanowire MOSFET selectors, where operational compatibility with the initial high‐field filament forming is established. Due to the small footprint of a vertical implementation, high density integration is achievable, and with a measured programming energy for 50 ns pulses at 0.49 pJ, the technology promises fast and ultralow power cross‐point memory arrays.
- 11 May 2020
- Published by Wiley in Advanced Electronic Materials
- Vol. 6 (6)
Open AccessCross‐Point Arrays with Low‐Power ITO‐HfO2 Resistive Memory Cells Integrated on Vertical III‐V Nanowires
Vertical nanowires with cointegrated metal‐oxide‐semiconductor field‐effect‐transistor (MOSFET) selectors and nonvolatile resistive random access memory (RRAM) cells represent a promising candidate for fast, energy‐efficient, cross‐point memory cells. This paper explores indium‐tin‐oxide‐hafnium‐dioxide RRAM cells integrated onto arrays of indium‐arsenide (InAs) vertical nanowires with a resulting area of 0.06 µm2 per cell. For low current operation, an improved switching uniformity over the intrinsic self‐compliant behavior is demonstrated when using an external InAs nanowire MOSFET selector in series. The memory cells show consistent switching voltages below ±1 V and a switching cycle endurance of 106 is demonstrated. The developed fabrication scheme is fully compatible with low‐ON‐resistance vertical III‐V nanowire MOSFET selectors, where operational compatibility with the initial high‐field filament forming is established. Due to the small footprint of a vertical implementation, high density integration is achievable, and with a measured programming energy for 50 ns pulses at 0.49 pJ, the technology promises fast and ultralow power cross‐point memory arrays.
- 1 December 2019
- Published by Elsevier in Materialia
- Vol. 8
Optimization of Platinum dioxide properties by plasma oxidation of sputtered PtOx
- 1 December 2019
- Published by Elsevier in Materialia
- Vol. 8
Optimization of Platinum dioxide properties by plasma oxidation of sputtered PtOx
- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 91-92
Investigation of Reverse Filament Formation in ITO/HfO2-based RRAM
To overcome the large discrepancy in speed between computational devices and that of contemporary large capacity non-volatile memory (NVM) technologies, resistive random access memory (RRAM) technologies are seen as promising candidates, offering speed/energy improvements in several orders of magnitude while being 3D integration compatible [1]. Indium-Tin-Oxide (ITO) has several unique properties for RRAM operation, perhaps most prominently the self-compliance and an ultra-low switching voltage $(\pm 200\ \mathrm{mV})$ [2]. We report on considerations for ITO electrical bottom electrode (BE) RRAM where we vary the ALD oxide deposition parameters in order to improve the reverse filament formation (RFF) occurring at large reset voltages. RFF is when the conducting filament is reformed. One of the key parameters of RRAM is the endurance, how many times it can switch before failure. The RFF is one of the limitations in the number of switches until a device reaches failure and it is thus of high importance to ensure a sufficient margin between the highest applied reset voltage and the RFF voltage not to compromise the endurance. We optimized the oxide to improve the RFF properties.- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 91-92
Investigation of Reverse Filament Formation in ITO/HfO2-based RRAM
To overcome the large discrepancy in speed between computational devices and that of contemporary large capacity non-volatile memory (NVM) technologies, resistive random access memory (RRAM) technologies are seen as promising candidates, offering speed/energy improvements in several orders of magnitude while being 3D integration compatible [1]. Indium-Tin-Oxide (ITO) has several unique properties for RRAM operation, perhaps most prominently the self-compliance and an ultra-low switching voltage $(\pm 200\ \mathrm{mV})$ [2]. We report on considerations for ITO electrical bottom electrode (BE) RRAM where we vary the ALD oxide deposition parameters in order to improve the reverse filament formation (RFF) occurring at large reset voltages. RFF is when the conducting filament is reformed. One of the key parameters of RRAM is the endurance, how many times it can switch before failure. The RFF is one of the limitations in the number of switches until a device reaches failure and it is thus of high importance to ensure a sufficient margin between the highest applied reset voltage and the RFF voltage not to compromise the endurance. We optimized the oxide to improve the RFF properties.