Bryan D. Allison
Research Subjects
Research Interests
Bryan D. Allison has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Ghatu Subhash
Department of Mechanical and Aerospace Engineering, University of Florida, Gainesville, USA
2 shared publications Nagaraj Arakere
Department of Mechanical and Aerospace Engineering, University of Florida, Gainesville, FL 32611
2 shared publications- Abir Bhattacharyya
Department of Materials Engineering Indian Institute of Technology Jodhpur Karwar Rajasthan India
1 shared publication Bryan McCoy
SKF Aeroengine North America, Falconer, NY 14701
1 shared publicationD. Haluck
Pratt & Whitney, 400 Main Street, East Hartford, CT 06108
1 shared publicationDavid A. Haluck
1 shared publication
Latest Publications
- 21 January 2016
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 138 (2) , 021003
Influence of Residual Stress and Temperature on the Cyclic Hardening Response of M50 High-Strength Bearing Steel Subjected to Rolling Contact Fatigue
Microstructural and mechanical characterization investigations on three variants of a through-hardened M50 bearing steel are presented to compare and contrast their performances under rolling contact fatigue (RCF) loading. Baseline (BL) variant of M50 steel bearing balls is subjected to: (i) a surface nitriding treatment and (ii) a surface mechanical processing treatment, to obtain distinct microstructures and mechanical properties. These balls are subjected to RCF loading for several hundred million cycles at two different test temperatures, and the subsequent changes in subsurface hardness and compressive stress–strain response are measured. It was found that the RCF-affected subsurface regions grow larger in size at higher temperature. Micro-indentation hardness measurements within the RCF-affected regions revealed an increase in hardness in all the three variants. The size of the RCF-affected region and intensity of hardening were the largest in the BL material and smallest in the mechanically processed (MP) material. Based on Goodman's diagram, it is shown that the compressive residual stress reduces the effective fully reversed alternating stress amplitude and thereby retards the initiation and evolution of subsurface plasticity within the material during RCF loading. It is quantitatively shown that high material hardness and compressive residual stress are greatly beneficial for enhancing the RCF life of bearings.
- 21 January 2016
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 138 (2) , 021003
Influence of Residual Stress and Temperature on the Cyclic Hardening Response of M50 High-Strength Bearing Steel Subjected to Rolling Contact Fatigue
Microstructural and mechanical characterization investigations on three variants of a through-hardened M50 bearing steel are presented to compare and contrast their performances under rolling contact fatigue (RCF) loading. Baseline (BL) variant of M50 steel bearing balls is subjected to: (i) a surface nitriding treatment and (ii) a surface mechanical processing treatment, to obtain distinct microstructures and mechanical properties. These balls are subjected to RCF loading for several hundred million cycles at two different test temperatures, and the subsequent changes in subsurface hardness and compressive stress–strain response are measured. It was found that the RCF-affected subsurface regions grow larger in size at higher temperature. Micro-indentation hardness measurements within the RCF-affected regions revealed an increase in hardness in all the three variants. The size of the RCF-affected region and intensity of hardening were the largest in the BL material and smallest in the mechanically processed (MP) material. Based on Goodman's diagram, it is shown that the compressive residual stress reduces the effective fully reversed alternating stress amplitude and thereby retards the initiation and evolution of subsurface plasticity within the material during RCF loading. It is quantitatively shown that high material hardness and compressive residual stress are greatly beneficial for enhancing the RCF life of bearings.
- 10 March 2014
- Published by Taylor & Francis in Tribology Transactions
- Vol. 57 (3) , 533-545
Influence of Initial Residual Stress on Material Properties of Bearing Steel During Rolling Contact Fatigue
- 10 March 2014
- Published by Taylor & Francis in Tribology Transactions
- Vol. 57 (3) , 533-545
Influence of Initial Residual Stress on Material Properties of Bearing Steel During Rolling Contact Fatigue
- 5 February 2014
- Published by ASME International in Journal of Tribology
- Vol. 136 (2) , 021103
Extraction and Testing of Miniature Compression Specimens From Bearing Balls Subjected to Rolling Contact Fatigue
Extraction and testing of miniature compression specimens from localized regions of components affected by rolling contact fatigue loading can provide significant insight into material degradation. Current ASTM standards for compression testing of cylindrical specimens become too stringent and difficult to achieve when specimen size is reduced to around 1 mm in diameter. The tolerances for surface flatness, parallelism of the loading surfaces, and the perpendicularity between the axis and the loading surfaces play crucial roles in the resulting stress-strain curves under uniaxial compression loading. In this manuscript, a systematic study is performed to quantify the influence of the above geometric parameters on the stress-strain response. Based on the analysis, the allowable geometric tolerances of miniature cylindrical specimens for a valid compression tests are recommended. The analysis results are validated and the usefulness of the method is demonstrated on miniature specimens extracted from the rolling contact fatigue affected regions of high strength M50 bearing balls. The yield stress within the rolling contact fatigue affected region is shown to increase by over 12%.
- 5 February 2014
- Published by ASME International in Journal of Tribology
- Vol. 136 (2) , 021103
Extraction and Testing of Miniature Compression Specimens From Bearing Balls Subjected to Rolling Contact Fatigue
Extraction and testing of miniature compression specimens from localized regions of components affected by rolling contact fatigue loading can provide significant insight into material degradation. Current ASTM standards for compression testing of cylindrical specimens become too stringent and difficult to achieve when specimen size is reduced to around 1 mm in diameter. The tolerances for surface flatness, parallelism of the loading surfaces, and the perpendicularity between the axis and the loading surfaces play crucial roles in the resulting stress-strain curves under uniaxial compression loading. In this manuscript, a systematic study is performed to quantify the influence of the above geometric parameters on the stress-strain response. Based on the analysis, the allowable geometric tolerances of miniature cylindrical specimens for a valid compression tests are recommended. The analysis results are validated and the usefulness of the method is demonstrated on miniature specimens extracted from the rolling contact fatigue affected regions of high strength M50 bearing balls. The yield stress within the rolling contact fatigue affected region is shown to increase by over 12%.
- 1 April 2012
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 36, 316-322
Effect of fiber waviness on the bending behavior of S-glass/epoxy composites
- 1 April 2012
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 36, 316-322
Effect of fiber waviness on the bending behavior of S-glass/epoxy composites