Chun-Pei Cho
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Chun-Pei Cho has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Tsong-Pyng Perng
5 shared publications- Tsong-Pyng Perng
Department of Materials Science and Engineering, National Tsing Hua University, Hsinchu 300, Taiwan
3 shared publications Yu-Chao Wang
3 shared publicationsChun-Chu Lin
Department of Applied Materials and Optoelectronic Engineering, National Chi Nan University, Nantou County 54561, Taiwan
2 shared publications- Hsin-Ya Chiu
Department of Applied Materials and Optoelectronic Engineering, National Chi Nan University, NanTou 54561, Taiwan
2 shared publications Lee-Hong Chang
2 shared publications
Latest Publications
- Open Access
Nitrogen Plasma-Assisted Surface Engineering on Multilayer Ti3C2Tx Electrodes for Enhanced Interfacial Charge Dynamics and Energy Storage in Ascorbic Acid Electrolyte
The intrinsic limitations of Ti3C2Tx electrodes, specifically low interfacial charge-transfer efficiency and structural degradation in strongly acidic environments, hinder their performance in high-rate aqueous supercapacitors. Herein, we report a synergistic strategy combining nitrogen plasma surface engineering with a redox-active ascorbic acid electrolyte to optimize the electrode/electrolyte interfacial kinetics. By systematic investigation, the Ti3C2Tx supercapacitor obtained by a 10-min plasma duration (N10P-AA) achieved the optimal balance between activating surface sites and preserving the conductive Ti–C framework integrity. The ascorbic acid electrolyte broadened the potential window to approximately 0.7 V, and N10P-AA exhibited the lowest charge-transfer impedance and superior rate capability, retaining a relatively high Coulombic efficiency (>72%) even at a high scan rate of 10,000 mV·s−1. The EIS results and kinetics analysis (b values) confirmed that the moderate plasma activation effectively promoted more surface-dominated charge storage kinetics and mitigated diffusion limitation, consistent with reduced charge-transfer resistance and a smaller Warburg slope. The XPS results revealed that the 10-min treatment suppressed detrimental oxidation during cyclings and facilitated the formation of electrochemically favorable hydroxylated surface functional groups. This work demonstrates a feasible surface electrolyte co-engineering strategy for modulating the interfacial behavior of MXene, which is of great significance for future high-efficiency aqueous electrochemical energy storage and potential biosensing applications.
Open AccessNitrogen Plasma-Assisted Surface Engineering on Multilayer Ti3C2Tx Electrodes for Enhanced Interfacial Charge Dynamics and Energy Storage in Ascorbic Acid Electrolyte
The intrinsic limitations of Ti3C2Tx electrodes, specifically low interfacial charge-transfer efficiency and structural degradation in strongly acidic environments, hinder their performance in high-rate aqueous supercapacitors. Herein, we report a synergistic strategy combining nitrogen plasma surface engineering with a redox-active ascorbic acid electrolyte to optimize the electrode/electrolyte interfacial kinetics. By systematic investigation, the Ti3C2Tx supercapacitor obtained by a 10-min plasma duration (N10P-AA) achieved the optimal balance between activating surface sites and preserving the conductive Ti–C framework integrity. The ascorbic acid electrolyte broadened the potential window to approximately 0.7 V, and N10P-AA exhibited the lowest charge-transfer impedance and superior rate capability, retaining a relatively high Coulombic efficiency (>72%) even at a high scan rate of 10,000 mV·s−1. The EIS results and kinetics analysis (b values) confirmed that the moderate plasma activation effectively promoted more surface-dominated charge storage kinetics and mitigated diffusion limitation, consistent with reduced charge-transfer resistance and a smaller Warburg slope. The XPS results revealed that the 10-min treatment suppressed detrimental oxidation during cyclings and facilitated the formation of electrochemically favorable hydroxylated surface functional groups. This work demonstrates a feasible surface electrolyte co-engineering strategy for modulating the interfacial behavior of MXene, which is of great significance for future high-efficiency aqueous electrochemical energy storage and potential biosensing applications.
- Open Access
Impacts of Mn Content and Mass Loading on the Performance of Flexible Asymmetric Solid-State Supercapacitors Using Mixed-Phase MnO2/N-Containing Graphene Composites as Cathode Materials
MnO2/nitrogen-containing graphene (x-NGM) composites with varying contents of Mn were used as the electrode materials for flexible asymmetric solid-state supercapacitors. The MnO2 was a two-phase mixture of γ- and α-MnO2. The combination of nitrogen-containing graphene and MnO2 improved reversible Faraday reactions and charge transfer. However, excessive MnO2 reduced conductivity, hindering ion diffusion and charge transfer. Overloading the electrode with active materials also negatively affected conductivity. Both the mass loading and MnO2 content were crucial to electrochemical performance. x-NGM composites served as cathode materials, while graphene acted as the anode material. Operating by two charge storage mechanisms enabled a synergistic effect, resulting in better charge storage purposes. Among the supercapacitors, the 3-NGM1//G1 exhibited the highest conductivity, efficient charge transfer, and superior capacitive characteristics. It showed a superior specific capacitance of 579 F·g−1, leading to high energy density and power density. Flexible solid-state supercapacitors using x-NGM composites demonstrated good cycle stability, with a high capacitance retention rate of 86.7% after 2000 bending cycles.
Open AccessImpacts of Mn Content and Mass Loading on the Performance of Flexible Asymmetric Solid-State Supercapacitors Using Mixed-Phase MnO2/N-Containing Graphene Composites as Cathode Materials
MnO2/nitrogen-containing graphene (x-NGM) composites with varying contents of Mn were used as the electrode materials for flexible asymmetric solid-state supercapacitors. The MnO2 was a two-phase mixture of γ- and α-MnO2. The combination of nitrogen-containing graphene and MnO2 improved reversible Faraday reactions and charge transfer. However, excessive MnO2 reduced conductivity, hindering ion diffusion and charge transfer. Overloading the electrode with active materials also negatively affected conductivity. Both the mass loading and MnO2 content were crucial to electrochemical performance. x-NGM composites served as cathode materials, while graphene acted as the anode material. Operating by two charge storage mechanisms enabled a synergistic effect, resulting in better charge storage purposes. Among the supercapacitors, the 3-NGM1//G1 exhibited the highest conductivity, efficient charge transfer, and superior capacitive characteristics. It showed a superior specific capacitance of 579 F·g−1, leading to high energy density and power density. Flexible solid-state supercapacitors using x-NGM composites demonstrated good cycle stability, with a high capacitance retention rate of 86.7% after 2000 bending cycles.
- 1 February 2019
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 223, 683-693
Enhanced photocatalytic characteristics by Ag-sensitized TiO2 photocatalysts with mixed phases
- 1 February 2019
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 223, 683-693
Enhanced photocatalytic characteristics by Ag-sensitized TiO2 photocatalysts with mixed phases
- Open Access
- 8 November 2018
- Published by MDPI AG in Nanomaterials
- Vol. 8 (11) , 924
Mixed-Phase MnO2/N-Containing Graphene Composites Applied as Electrode Active Materials for Flexible Asymmetric Solid-State Supercapacitors
MnO2/N-containing graphene composites with various contents of Mn were fabricated and used as active materials for the electrodes of flexible solid-state asymmetric supercapacitors. By scanning electron microscopes (SEM), transmission electron microscope (TEM), energy-dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectrometer (XPS), fourier-transform infrared spectroscopy (FTIR) and Raman spectra, the presence of MnO2 and N-containing graphene was verified. The MnO2 nanostructures decorated on the N-containing graphene were of α- and γ-mixed phases. N-containing graphene was found to reduce the charge transfer impedance in the high-frequency region at the electrode/electrolyte interface (RCT) due to its good conductivity. The co-existence of MnO2 and N-containing graphene led to a more reduced RCT and improved charge transfer. Both the mass loading and content of Mn in an active material electrode were crucial. Excess Mn caused reduced contacts between the electrode and electrolyte ions, leading to increased RCT, and suppressed ionic diffusion. When the optimized mass loading and Mn content were used, the 3-NGM1 electrode exhibiting the smallest RCT and a lower ionic diffusion impedance was obtained. It also showed a high specific capacitance of 638 F·g−1 by calculation from the cyclic voltammetry (CV) curves. The corresponding energy and power densities were 372.7 Wh·kg−1 and 4731.1 W·kg−1, respectively. The superior capacitance property arising from the synergistic effect of mixed-phase MnO2 and N-containing graphene had permitted the composites promising active materials for flexible solid-state asymmetric supercapacitors. Moreover, the increase of specific capacitance was found to be more significant by the pseudocapacitive MnO2 than N-containing graphene.
- 8 November 2018
- Published by MDPI AG in Nanomaterials
- Vol. 8 (11) , 924
Open AccessMixed-Phase MnO2/N-Containing Graphene Composites Applied as Electrode Active Materials for Flexible Asymmetric Solid-State Supercapacitors
MnO2/N-containing graphene composites with various contents of Mn were fabricated and used as active materials for the electrodes of flexible solid-state asymmetric supercapacitors. By scanning electron microscopes (SEM), transmission electron microscope (TEM), energy-dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectrometer (XPS), fourier-transform infrared spectroscopy (FTIR) and Raman spectra, the presence of MnO2 and N-containing graphene was verified. The MnO2 nanostructures decorated on the N-containing graphene were of α- and γ-mixed phases. N-containing graphene was found to reduce the charge transfer impedance in the high-frequency region at the electrode/electrolyte interface (RCT) due to its good conductivity. The co-existence of MnO2 and N-containing graphene led to a more reduced RCT and improved charge transfer. Both the mass loading and content of Mn in an active material electrode were crucial. Excess Mn caused reduced contacts between the electrode and electrolyte ions, leading to increased RCT, and suppressed ionic diffusion. When the optimized mass loading and Mn content were used, the 3-NGM1 electrode exhibiting the smallest RCT and a lower ionic diffusion impedance was obtained. It also showed a high specific capacitance of 638 F·g−1 by calculation from the cyclic voltammetry (CV) curves. The corresponding energy and power densities were 372.7 Wh·kg−1 and 4731.1 W·kg−1, respectively. The superior capacitance property arising from the synergistic effect of mixed-phase MnO2 and N-containing graphene had permitted the composites promising active materials for flexible solid-state asymmetric supercapacitors. Moreover, the increase of specific capacitance was found to be more significant by the pseudocapacitive MnO2 than N-containing graphene.
- Open Access
Ag3PO4-TiO2-Graphene Oxide Ternary Composites with Efficient Photodegradation, Hydrogen Evolution, and Antibacterial Properties
Ag3PO4-TiO2-graphene oxide ternary composite photocatalysts were fabricated by the photocatalytic reduction and ion exchange methods. The properties and photocatalytic activity of the composites were examined, and the photodegradation mechanism was investigated. More TiO2 nanoparticles in the composites were found to improve light absorption, but caused a larger impedance and inferior charge transport. Excess TiO2 nanoparticles distributed over the surfaces of Ag3PO4 and graphene oxide decreased the specific surface area and thus lowered light absorbance. An appropriate TiO2 content enhanced photocatalytic performance. When the molar ratio of Ag3PO4 to TiO2 was 0.6, the highest efficiency in photodegradation, hydrogen production (with a quantum efficiency of 8.1% and a hydrogen evolution rate of 218.7 μmole·g−1·h−1) and bacterial inactivation was achieved. Trapping experiments demonstrated that superoxide radicals and holes are the major active species involved in the photodegradation process.
Open AccessAg3PO4-TiO2-Graphene Oxide Ternary Composites with Efficient Photodegradation, Hydrogen Evolution, and Antibacterial Properties
Ag3PO4-TiO2-graphene oxide ternary composite photocatalysts were fabricated by the photocatalytic reduction and ion exchange methods. The properties and photocatalytic activity of the composites were examined, and the photodegradation mechanism was investigated. More TiO2 nanoparticles in the composites were found to improve light absorption, but caused a larger impedance and inferior charge transport. Excess TiO2 nanoparticles distributed over the surfaces of Ag3PO4 and graphene oxide decreased the specific surface area and thus lowered light absorbance. An appropriate TiO2 content enhanced photocatalytic performance. When the molar ratio of Ag3PO4 to TiO2 was 0.6, the highest efficiency in photodegradation, hydrogen production (with a quantum efficiency of 8.1% and a hydrogen evolution rate of 218.7 μmole·g−1·h−1) and bacterial inactivation was achieved. Trapping experiments demonstrated that superoxide radicals and holes are the major active species involved in the photodegradation process.
- 9 January 2018
- Published by Wiley in ChemistrySelect
- Vol. 3 (2) , 354-362
High Efficiency for Hydrogen Evolution and Bacterial Inactivation of Ag‐TiO 2 ‐Graphene Ternary Nanocomposites with Appropriate Ag Ratios
Ag‐TiO 2 ‐graphene (ATG) ternary nanocomposites with various Ag contents were synthesized at fixed mixing ratios of TiO 2 to graphene. The successful fabrication of them was confirmed by XRD, SEM, TEM, Raman and XPS spectra. The stronger Raman signals caused by the increased Ag content were considered as a significant evidence for the SPR effect. An increased Ag content gave rise to not only a wider absorption range but also a higher visible‐light absorbance. The results of electrochemical analysis illustrated that more Ag loading caused a reduced interfacial impedance, and improved conductivity and electron transport. However, excess Ag nanoparticles led to agglomeration and decreased surface area unfavorable to light absorption. Thus, an appropriate Ag content was required to achieve higher optical response and photocatalytic efficiency. It was found that for each fixed mixing ratio of TiO 2 and graphene, there was a corresponding optimum Ag content. The hydrogen evolution results displayed the same trend as photodegradation, indicating again that the optimum ratio of TiO 2 and graphene was 5: 1, and the extent of Ag loading was really crucial. By appropriate ratios of graphene and Ag, A 15 TG(5) exhibited the highest efficiency in both photodegradation and hydrogen evolution. Its QE and mass‐normalized hydrogen evolution rate were 26.2% and 705.6 μmol⋅g −1 ⋅h −1 , respectively. Furthermore, the ATG nanocomposites also showed promising capability for bacterial inactivation.
- 9 January 2018
- Published by Wiley in ChemistrySelect
- Vol. 3 (2) , 354-362
High Efficiency for Hydrogen Evolution and Bacterial Inactivation of Ag‐TiO 2 ‐Graphene Ternary Nanocomposites with Appropriate Ag Ratios
Ag‐TiO 2 ‐graphene (ATG) ternary nanocomposites with various Ag contents were synthesized at fixed mixing ratios of TiO 2 to graphene. The successful fabrication of them was confirmed by XRD, SEM, TEM, Raman and XPS spectra. The stronger Raman signals caused by the increased Ag content were considered as a significant evidence for the SPR effect. An increased Ag content gave rise to not only a wider absorption range but also a higher visible‐light absorbance. The results of electrochemical analysis illustrated that more Ag loading caused a reduced interfacial impedance, and improved conductivity and electron transport. However, excess Ag nanoparticles led to agglomeration and decreased surface area unfavorable to light absorption. Thus, an appropriate Ag content was required to achieve higher optical response and photocatalytic efficiency. It was found that for each fixed mixing ratio of TiO 2 and graphene, there was a corresponding optimum Ag content. The hydrogen evolution results displayed the same trend as photodegradation, indicating again that the optimum ratio of TiO 2 and graphene was 5: 1, and the extent of Ag loading was really crucial. By appropriate ratios of graphene and Ag, A 15 TG(5) exhibited the highest efficiency in both photodegradation and hydrogen evolution. Its QE and mass‐normalized hydrogen evolution rate were 26.2% and 705.6 μmol⋅g −1 ⋅h −1 , respectively. Furthermore, the ATG nanocomposites also showed promising capability for bacterial inactivation.
- 1 July 2017
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 42 (27) , 17020-17029
Investigation of the appropriate content of graphene in Ag TiO2-graphene ternary nanocomposites applied as photocatalysts
- 1 July 2017
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 42 (27) , 17020-17029
Investigation of the appropriate content of graphene in Ag TiO2-graphene ternary nanocomposites applied as photocatalysts
- 1 January 2017
- Published by Elsevier in Journal of Photochemistry and Photobiology A: Chemistry
- Vol. 332, 1-9
Application of TiO2-graphene nanocomposites to photoanode of dye-sensitized solar cell
- 1 January 2017
- Published by Elsevier in Journal of Photochemistry and Photobiology A: Chemistry
- Vol. 332, 1-9
Application of TiO2-graphene nanocomposites to photoanode of dye-sensitized solar cell
- 1 December 2016
- Published by Elsevier in Solid State Sciences
- Vol. 62, 112-120
Exploration of silver decoration concentration to enhance photocatalytic efficiency of titanium dioxide photocatalysts
- 1 December 2016
- Published by Elsevier in Solid State Sciences
- Vol. 62, 112-120
Exploration of silver decoration concentration to enhance photocatalytic efficiency of titanium dioxide photocatalysts