Tatiana Pavlovna Romanova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Tatiana Pavlovna Romanova has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Yu. V. Nemirovskii
9 shared publications- Andrei Petrovich Yankovskii
Khristianovich Institute of Theoretical and Applied Mechanics SB RAS, Novosibirsk, Russia
7 shared publications - Yu. V. Nemirovskii
Russian Academy of Sciences
5 shared publications A. P. Yankovskii
S. A. Khristianovich Institute of Theoretical and Applied Mechanics of the Siberian Branch of the Russian Academy of Sciences, Novosibirsk, Russia
2 shared publicationsYu. V. Nemirovsky
Institute of Theoretical and Applied Mechanics, Siberian Division, Russian Academy of Sciences
2 shared publicationsТатьяна Павловна Романова
Институт теоретической и прикладной механики им. С. А. Христиановича СО РАН, г. Новосибирск, 630090, Россия
2 shared publications
Latest Publications
- 21 March 2024
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 31 (30) , 12721-12739
Rigid-plastic behavior and bearing capacity of thin flat reinforced rotating disks
1. The problem of modeling the mechanical behavior of composite disks at high rotational speeds is very important [1–13]. Examples of such disks are steam and gas turbine rotors, turbo generators, ...
- 21 March 2024
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 31 (30) , 12721-12739
Rigid-plastic behavior and bearing capacity of thin flat reinforced rotating disks
1. The problem of modeling the mechanical behavior of composite disks at high rotational speeds is very important [1–13]. Examples of such disks are steam and gas turbine rotors, turbo generators, ...
- 4 April 2023
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 31 (18) , 4387-4398
Investigation of load-bearing capacity of rigid-plastic reinforced ellipsoidal shells of rotation
For ellipsoidal fiber-reinforced shells of rotation, the upper (kinematic) limit of load-bearing capacity is determined. The structures are clamped along the lower support contour and have rigid polar plate. The material of the components is rigid-plastic with asymmetry in tension and compression. The matrix is orthotropic. The principal axes of matrix anisotropy coincide with meridional, circumferential and transverse directions. Two-layer shell model and refined relations of structural model with two-dimensional stress state in components are used. Extreme problem is formulated and numerically solved for spherical and two different ellipsoidal shells. Influence of reinforcement parameters on limit load is investigated.
- 4 April 2023
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 31 (18) , 4387-4398
Investigation of load-bearing capacity of rigid-plastic reinforced ellipsoidal shells of rotation
For ellipsoidal fiber-reinforced shells of rotation, the upper (kinematic) limit of load-bearing capacity is determined. The structures are clamped along the lower support contour and have rigid polar plate. The material of the components is rigid-plastic with asymmetry in tension and compression. The matrix is orthotropic. The principal axes of matrix anisotropy coincide with meridional, circumferential and transverse directions. Two-layer shell model and refined relations of structural model with two-dimensional stress state in components are used. Extreme problem is formulated and numerically solved for spherical and two different ellipsoidal shells. Influence of reinforcement parameters on limit load is investigated.
- 27 February 2022
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 30 (8) , 1692-1702
Mathematical modeling the rigid-plastic yielding behavior of fibrous flatly-reinforced composites of anisotropic materials at 2D stress state
Structural model of multi-directed flatly-reinforced hybrid composites allowing one to determine the yield loci for the composition with account plane stress state in all components is developed. The fiber and matrix materials are homogeneous and anisotropic. Their mechanical behavior is described by associated flow law for rigid-perfectly plastic body with quadratic Mises – Hill yield criterion. As examples, two variants of symmetrical reinforcement for compositions consisting of orthotropic materials are considered under condition of equal reinforcement consumption. The influence of anisotropy characteristics of components and reinforcement parameters on shape and dimensions of the yield loci of the compositions is investigated.
- 27 February 2022
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 30 (8) , 1692-1702
Mathematical modeling the rigid-plastic yielding behavior of fibrous flatly-reinforced composites of anisotropic materials at 2D stress state
Structural model of multi-directed flatly-reinforced hybrid composites allowing one to determine the yield loci for the composition with account plane stress state in all components is developed. The fiber and matrix materials are homogeneous and anisotropic. Their mechanical behavior is described by associated flow law for rigid-perfectly plastic body with quadratic Mises – Hill yield criterion. As examples, two variants of symmetrical reinforcement for compositions consisting of orthotropic materials are considered under condition of equal reinforcement consumption. The influence of anisotropy characteristics of components and reinforcement parameters on shape and dimensions of the yield loci of the compositions is investigated.
- 16 August 2021
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 29 (26) , 5651-5665
Load-bearing capacity of rigid-plastic reinforced shallow shells and plates
The extreme problem of finding upper (kinematic) limit load of rigid-plastic fiber-reinforced spherical shallow shells and plates, which are circular in plan, is formulated and solved. The structures are clamped and have rigid insert. Two-layer shell model is used. The materials of components are rigid-perfectly plastic and asymmetric in tension and compression. The binder is isotropic or orthotropic. The structural model of composition takes into account two-dimensional stress state in the components. The piecewise-linear yield curves are constructed for radial-circumferential and spiral reinforcement. Comparisons results with other studies are given and influence of reinforcement parameters on limit load is investigated.
- 16 August 2021
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 29 (26) , 5651-5665
Load-bearing capacity of rigid-plastic reinforced shallow shells and plates
The extreme problem of finding upper (kinematic) limit load of rigid-plastic fiber-reinforced spherical shallow shells and plates, which are circular in plan, is formulated and solved. The structures are clamped and have rigid insert. Two-layer shell model is used. The materials of components are rigid-perfectly plastic and asymmetric in tension and compression. The binder is isotropic or orthotropic. The structural model of composition takes into account two-dimensional stress state in the components. The piecewise-linear yield curves are constructed for radial-circumferential and spiral reinforcement. Comparisons results with other studies are given and influence of reinforcement parameters on limit load is investigated.
- 18 January 2021
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 29 (18) , 2668-2679
Structural model for spatially and flatly reinforced medium of rigid-plastic materials considering three-dimensional stress state in all components
Structural models are constructed for hybrid fiber composite medium, three-dimensional reinforced, and for particular two-dimensional problems. They allow one to determine yield loci for the composition. Three-dimensional stress state in all components is considered. The materials of the composition components are homogeneous and isotropic. Their mechanical behavior is described by the associated flow rule for rigid plastic bodies with quadratic yield conditions. The components have different yield points in tension and compression. The stresses in the components are presented in parametric form for performing constructions. As example, the yield loci are constructed for metal-compositions of magnesium binder and steel fibers.
- 18 January 2021
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 29 (18) , 2668-2679
Structural model for spatially and flatly reinforced medium of rigid-plastic materials considering three-dimensional stress state in all components
Structural models are constructed for hybrid fiber composite medium, three-dimensional reinforced, and for particular two-dimensional problems. They allow one to determine yield loci for the composition. Three-dimensional stress state in all components is considered. The materials of the composition components are homogeneous and isotropic. Their mechanical behavior is described by the associated flow rule for rigid plastic bodies with quadratic yield conditions. The components have different yield points in tension and compression. The stresses in the components are presented in parametric form for performing constructions. As example, the yield loci are constructed for metal-compositions of magnesium binder and steel fibers.
- 1 December 2020
- Published by Allerton Press in Mechanics of Solids
- Vol. 55 (8) , 1235-1252
Piecewise-Linear Yield Loci of Angle-Ply Reinforced Medium of Different-Resisting Rigid-Plastic Materials at 2D Stress State
The structural model of hybrid composites angle-ply that were reinforced parallel to some plane is constructed for the analytical determination of the comp
- 1 December 2020
- Published by Allerton Press in Mechanics of Solids
- Vol. 55 (8) , 1235-1252
Piecewise-Linear Yield Loci of Angle-Ply Reinforced Medium of Different-Resisting Rigid-Plastic Materials at 2D Stress State
The structural model of hybrid composites angle-ply that were reinforced parallel to some plane is constructed for the analytical determination of the comp
- 20 October 2020
- Published by SAGE Publications in Mathematics and Mechanics of Solids
- Vol. 26 (4) , 570-590
Modeling the dynamic bending of rigid-plastic fiber-reinforced laminated curvilinear doubly connected thin plates with free outer contour
A theoretical model of the dynamic bending of rigid-plastic hybrid composite, arbitrary curvilinear doubly connected thin plates is developed. Inner contour of the plate is simply supported or clamped and outer one is free. The plates are on a viscous basis and under the action of uniformly distributed loads of explosive type. The plates are laminated and fibrous, with layers arranged symmetrically with respect to the middle surface. In each layer the reinforcing fibers, made of different materials, are located in directions parallel or normal to inner contour of plate. The structural model of the reinforced layer considering the plane stress state in fibers is used. The equations of the dynamic deformation of plate and simple analytical formula for the limit load are obtained. Numerical examples are given for a fiber-reinforced four-layered curvilinear plate with a supported hole in the form of ellipse and super-ellipse at the same total amount of reinforcement.
- 20 October 2020
- Published by SAGE Publications in Mathematics and Mechanics of Solids
- Vol. 26 (4) , 570-590
Modeling the dynamic bending of rigid-plastic fiber-reinforced laminated curvilinear doubly connected thin plates with free outer contour
A theoretical model of the dynamic bending of rigid-plastic hybrid composite, arbitrary curvilinear doubly connected thin plates is developed. Inner contour of the plate is simply supported or clamped and outer one is free. The plates are on a viscous basis and under the action of uniformly distributed loads of explosive type. The plates are laminated and fibrous, with layers arranged symmetrically with respect to the middle surface. In each layer the reinforcing fibers, made of different materials, are located in directions parallel or normal to inner contour of plate. The structural model of the reinforced layer considering the plane stress state in fibers is used. The equations of the dynamic deformation of plate and simple analytical formula for the limit load are obtained. Numerical examples are given for a fiber-reinforced four-layered curvilinear plate with a supported hole in the form of ellipse and super-ellipse at the same total amount of reinforcement.
- 31 January 2020
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 28 (20) , 2151-2162
Structural model for rigid-plastic yielding behavior of angle-ply reinforced composites of materials with different properties in tension and compression considering 2D stress state in all components
Structural model for hybrid media, angle-ply reinforced in the plane allowing one to determine the yield loci for the composition considering the plane stress state in all components is constructed. The materials of the composition are homogeneous, isotropic and have different yield strengths in tension and compression. Their mechanical behavior is described by the associated flow rule for rigid-plastic bodies with the quadratic yield conditions. The yield loci for metal compositions with low-strength and high-strength binder and for glass-plastic composition are calculated.
- 31 January 2020
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 28 (20) , 2151-2162
Structural model for rigid-plastic yielding behavior of angle-ply reinforced composites of materials with different properties in tension and compression considering 2D stress state in all components
Structural model for hybrid media, angle-ply reinforced in the plane allowing one to determine the yield loci for the composition considering the plane stress state in all components is constructed. The materials of the composition are homogeneous, isotropic and have different yield strengths in tension and compression. Their mechanical behavior is described by the associated flow rule for rigid-plastic bodies with the quadratic yield conditions. The yield loci for metal compositions with low-strength and high-strength binder and for glass-plastic composition are calculated.