Muhammed Fatih Can
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Muhammed Fatih Can has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Mehmet Sabri Celik
Istanbul Technical University
5 shared publications - Birgül Benli
Istanbul Technical University
2 shared publications Mehmet Sabri Çelik
2 shared publicationsA. Rıza Erdem
Chemistry Department, Istanbul Technical University, Istanbul 34469, Turkey
1 shared publication- Ahmet Yıldız
Afyon Kocatepe Universitesi
1 shared publication - Ali Ekrem Aritan
Afyon Kocatepe Üniversitesi, Mühendislik Fakültesi, Maden Mühendisliği Bölümü
1 shared publication
Latest Publications
- Open Access
- 6 October 2026
- Published by Afyon Kocatepe Universitesi Fen Ve Muhendislik Bilimleri Dergisi in Afyon Kocatepe University Journal of Sciences and Engineering
- Vol. 26 (5) , 1226-1237
Kapalı Çevrim Elektrokoagülasyon ve Zenginleştirme Sistemi (CEED) ile Jeotermal Sulardan Silika Bakımından Zengin Nano Boyutlu Ürün Geri Kazanımı
Jeotermal enerji sistemlerinde önemli işletme problemlerinden biri, çözünmüş silis türlerinin polimerizasyon ve çökelme süreçleri sonucunda katı silika fazına dönüşerek ekipman yüzeylerinde silika tortuları oluşturmasıdır. Bununla birlikte, bu fizikokimyasal dönüşüm silika bazlı katma değerli ürünlerin geri kazanımı için önemli bir potansiyel sunmaktadır. Bu çalışmada, Afyonkarahisar Ömer-Gecek jeotermal sahasından temin edilen termal sulardan elektrokoagülasyon yöntemiyle silika bakımından zengin nano boyutlu katı ürünlerin geri kazanımı araştırılmıştır. Geliştirilen Kapalı Çevrim Elektrokoagülasyon ve Zenginleştirme Sistemi (CEED) ile açık ve kapalı çevrim işletme koşulları karşılaştırılmıştır. Deneyler 0.50–1.50 A akım aralığında ve 16.5–62.5 mL/dk debilerde gerçekleştirilmiştir. Kapalı çevrim sistemde en yüksek katı ürün miktarı 1.50 A ve 62.5 mL/dk koşullarında 0.425 mg/mL olarak belirlenmiş ve açık çevrime göre %41.7 daha yüksek geri kazanım elde edilmiştir. Ürün geri kazanım deneylerinde maksimum değer 1.50 A/V2 koşulunda 0.709 mg/mL olarak saptanmıştır. SEM analizleri ortalama 279 nm partikül boyutunu, EDS analizleri ise geri kazanılan ürünün yaklaşık %68.5 SiO₂ içerdiğini göstermiştir. Bulgular, CEED yaklaşımının çözünmüş silis türlerinin elektrokoagülasyon destekli kontrollü çökelmesini sağlayarak bunların silika bakımından zengin nano boyutlu katı ürünler olarak eş zamanlı geri kazanımı için etkili ve uygulanabilir bir yöntem olduğunu ortaya koymuştur.
- 6 October 2026
- Published by Afyon Kocatepe Universitesi Fen Ve Muhendislik Bilimleri Dergisi in Afyon Kocatepe University Journal of Sciences and Engineering
- Vol. 26 (5) , 1226-1237
Open AccessKapalı Çevrim Elektrokoagülasyon ve Zenginleştirme Sistemi (CEED) ile Jeotermal Sulardan Silika Bakımından Zengin Nano Boyutlu Ürün Geri Kazanımı
Jeotermal enerji sistemlerinde önemli işletme problemlerinden biri, çözünmüş silis türlerinin polimerizasyon ve çökelme süreçleri sonucunda katı silika fazına dönüşerek ekipman yüzeylerinde silika tortuları oluşturmasıdır. Bununla birlikte, bu fizikokimyasal dönüşüm silika bazlı katma değerli ürünlerin geri kazanımı için önemli bir potansiyel sunmaktadır. Bu çalışmada, Afyonkarahisar Ömer-Gecek jeotermal sahasından temin edilen termal sulardan elektrokoagülasyon yöntemiyle silika bakımından zengin nano boyutlu katı ürünlerin geri kazanımı araştırılmıştır. Geliştirilen Kapalı Çevrim Elektrokoagülasyon ve Zenginleştirme Sistemi (CEED) ile açık ve kapalı çevrim işletme koşulları karşılaştırılmıştır. Deneyler 0.50–1.50 A akım aralığında ve 16.5–62.5 mL/dk debilerde gerçekleştirilmiştir. Kapalı çevrim sistemde en yüksek katı ürün miktarı 1.50 A ve 62.5 mL/dk koşullarında 0.425 mg/mL olarak belirlenmiş ve açık çevrime göre %41.7 daha yüksek geri kazanım elde edilmiştir. Ürün geri kazanım deneylerinde maksimum değer 1.50 A/V2 koşulunda 0.709 mg/mL olarak saptanmıştır. SEM analizleri ortalama 279 nm partikül boyutunu, EDS analizleri ise geri kazanılan ürünün yaklaşık %68.5 SiO₂ içerdiğini göstermiştir. Bulgular, CEED yaklaşımının çözünmüş silis türlerinin elektrokoagülasyon destekli kontrollü çökelmesini sağlayarak bunların silika bakımından zengin nano boyutlu katı ürünler olarak eş zamanlı geri kazanımı için etkili ve uygulanabilir bir yöntem olduğunu ortaya koymuştur.
- Open Access
- 27 September 2026
- Published by Politechnika Wroclawska Oficyna Wydawnicza in Physicochemical Problems of Mineral Processing
- Vol. 62 (5)
Extraction of tar from Turkish coals of various ranks by pyrolysis and application of solvent extraction method for carbon fiber production
Carbon fibers with their high performance are critically important materials for various industries. Coal-based isotropic and mesophase pitches, despite their smaller market share of 10%, can be good alternative to polyacrylonitrile (PAN) based carbon fiber particularly for premium markets such as aviation and defense industry where extraordinary properties like high thermal conductivity and Young modulus are required. Pitch-based carbon fiber production is a complicated process including raw material pretreatment, pitch preparation, melt-spinning, stabilization, carbonization, and graphitization. Each step has a significant influence on the properties and performance of the final carbon fiber product, and thus should be controlled effectively for preparing carbon fiber with desirable performance. In this study, a pyrolysis study has been undertaken on eight Turkish coals of different ranks from lignite to bituminous coals with ash contents varying from 7.25 to 49.20%. The coals have been pyrolyzed at 850 ºC for two hours under nitrogen atmosphere in the absence of oxygen during which the emission of released gases of H2, CO2, CO and CH4 in situ measured. The amounts of char, tar and gas have been recorded for each coal. The results based on tar recoveries and aromatic groups as inferred from FTIR spectra were evaluated to find a suitable precursor for use in carbon fiber production. Kısrakdere lignite/sub-bituminous coal were selected and subjected to solvent extraction with tetraline at 400 ºC temperature and 100 bar pressure to determine the potential of this particular coal for carbon fiber development.
- 27 September 2026
- Published by Politechnika Wroclawska Oficyna Wydawnicza in Physicochemical Problems of Mineral Processing
- Vol. 62 (5)
Open AccessExtraction of tar from Turkish coals of various ranks by pyrolysis and application of solvent extraction method for carbon fiber production
Carbon fibers with their high performance are critically important materials for various industries. Coal-based isotropic and mesophase pitches, despite their smaller market share of 10%, can be good alternative to polyacrylonitrile (PAN) based carbon fiber particularly for premium markets such as aviation and defense industry where extraordinary properties like high thermal conductivity and Young modulus are required. Pitch-based carbon fiber production is a complicated process including raw material pretreatment, pitch preparation, melt-spinning, stabilization, carbonization, and graphitization. Each step has a significant influence on the properties and performance of the final carbon fiber product, and thus should be controlled effectively for preparing carbon fiber with desirable performance. In this study, a pyrolysis study has been undertaken on eight Turkish coals of different ranks from lignite to bituminous coals with ash contents varying from 7.25 to 49.20%. The coals have been pyrolyzed at 850 ºC for two hours under nitrogen atmosphere in the absence of oxygen during which the emission of released gases of H2, CO2, CO and CH4 in situ measured. The amounts of char, tar and gas have been recorded for each coal. The results based on tar recoveries and aromatic groups as inferred from FTIR spectra were evaluated to find a suitable precursor for use in carbon fiber production. Kısrakdere lignite/sub-bituminous coal were selected and subjected to solvent extraction with tetraline at 400 ºC temperature and 100 bar pressure to determine the potential of this particular coal for carbon fiber development.
- Open Access
- 19 September 2026
- Published by Politechnika Wroclawska Oficyna Wydawnicza in Physicochemical Problems of Mineral Processing
- Vol. 62 (7)
Short-range acid–base (hydration) forces as a dominant control on albite/orthoclase flotation selectivity: a colloidal-probe AFM and extended-DLVO study
Selective flotation of albite from potassium feldspar (microcline/orthoclase) with cationic collectors is controlled by monovalent salt, yet the surface forces responsible have been inferred from electrokinetic and thermodynamic data rather than measured directly. Here we probe these interactions by colloidal-probe atomic force microscopy (AFM), interpreted through classical and extended DLVO theory. Force curves between a silica microsphere and polished albite and orthoclase surfaces were acquired versus NaCl and at the separation condition. Constant-potential DLVO fits returned Debye lengths of the expected order, and effective potentials reproducing the electrokinetic ordering (albite more negative than orthoclase) and, at high ionic strength, resolving a mineral-distinguishing difference absent from the zeta potentials. Surface free-energy components from thin-layer wicking resolved the forces into Lifshitz–van der Waals, double-layer, and Lewis acid–base contributions. Added electrolyte shortened the force range through double-layer compression, while a non-DLVO short-range repulsion re-emerged at high ionic strength. At the separation condition, albite showed a stronger short-range repulsion than orthoclase; a rigorous van Oss decomposition attributes this to a repulsive acid–base (hydration-type) force more than twice as strong on albite, mirroring selectivity, whereas a simplified rule returns an attractive term contradicting the measurement. With the amine collector present, the force resolves its action directly: it weakens the albite repulsion, the direct-force counterpart of orthoclase’s faster, thermodynamically established hydrophobization. Short-range acid–base and hydration forces, rather than the double-layer force, emerge as the dominant contribution distinguishing the two feldspars; the continuum model captures the sign and ordering of this control but not its magnitude.
- 19 September 2026
- Published by Politechnika Wroclawska Oficyna Wydawnicza in Physicochemical Problems of Mineral Processing
- Vol. 62 (7)
Open AccessShort-range acid–base (hydration) forces as a dominant control on albite/orthoclase flotation selectivity: a colloidal-probe AFM and extended-DLVO study
Selective flotation of albite from potassium feldspar (microcline/orthoclase) with cationic collectors is controlled by monovalent salt, yet the surface forces responsible have been inferred from electrokinetic and thermodynamic data rather than measured directly. Here we probe these interactions by colloidal-probe atomic force microscopy (AFM), interpreted through classical and extended DLVO theory. Force curves between a silica microsphere and polished albite and orthoclase surfaces were acquired versus NaCl and at the separation condition. Constant-potential DLVO fits returned Debye lengths of the expected order, and effective potentials reproducing the electrokinetic ordering (albite more negative than orthoclase) and, at high ionic strength, resolving a mineral-distinguishing difference absent from the zeta potentials. Surface free-energy components from thin-layer wicking resolved the forces into Lifshitz–van der Waals, double-layer, and Lewis acid–base contributions. Added electrolyte shortened the force range through double-layer compression, while a non-DLVO short-range repulsion re-emerged at high ionic strength. At the separation condition, albite showed a stronger short-range repulsion than orthoclase; a rigorous van Oss decomposition attributes this to a repulsive acid–base (hydration-type) force more than twice as strong on albite, mirroring selectivity, whereas a simplified rule returns an attractive term contradicting the measurement. With the amine collector present, the force resolves its action directly: it weakens the albite repulsion, the direct-force counterpart of orthoclase’s faster, thermodynamically established hydrophobization. Short-range acid–base and hydration forces, rather than the double-layer force, emerge as the dominant contribution distinguishing the two feldspars; the continuum model captures the sign and ordering of this control but not its magnitude.
- Open Access
- 11 July 2024
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 39 (2) , 467-474
Doğaltaş Madenciliğinde Ocak-Fabrika Ortamında Titreşim ve Gürültü Maruziyetinin Araştırılması
Bu çalışmada; Ülkemiz madenciliğinde önemli yer tutan doğaltaş ocak-tesislerinde, standart/yönetmeliklere uygun alınan titreşim ve gürültü ölçümleri alınmıştır. Elde edilen sonuçlar Gürültü ve Titreşim Yönetmeliğine göre değerlendirilmiştir. Ocaklardan alınan ölçümlerde, sondaj makinesi kullanan operatörlerinin hem tüm vücut titreşimi (4,8 m/s2) hem de gürültü maruziyetinin (89,3 dBA) yüksek olduğu görülmüştür. Fabrikadan alınan gürültü ölçüm değerlerinde ise S/T makinelerinin (90,6 dBA), ebatlama makinelerinden (85,5 dBA) daha fazla gürültüye yol açtıkları ortaya çıkmıştır. Elmas tel kesme makinesi kullanan çalışanların el-kol titreşimi ölçümlerinde elde edilen değerlerde her ne kadar günlük maruziyet sınır değeri olan 5 m/s2 değerinin aşılmadığı görülmüş ise de günlük maruziyet eylem değeri olan 2,5 m/s2’nin iki ocakta aşıldığı görülmüştür. Çalışmada son olarak, yapılan ölçümler sonucunda elde edilen verilerdeki sınır değerlerin üzerindeki değerlerle ilgili olarak ocaklar/fabrikada alınabilecek önlemler sunulmuştur.
- 11 July 2024
- Published by Cukurova Universitesi Muhendislik-Mimarlik Fakultesi Dergisi in Çukurova Üniversitesi Mühendislik Fakültesi Dergisi
- Vol. 39 (2) , 467-474
Open AccessDoğaltaş Madenciliğinde Ocak-Fabrika Ortamında Titreşim ve Gürültü Maruziyetinin Araştırılması
Bu çalışmada; Ülkemiz madenciliğinde önemli yer tutan doğaltaş ocak-tesislerinde, standart/yönetmeliklere uygun alınan titreşim ve gürültü ölçümleri alınmıştır. Elde edilen sonuçlar Gürültü ve Titreşim Yönetmeliğine göre değerlendirilmiştir. Ocaklardan alınan ölçümlerde, sondaj makinesi kullanan operatörlerinin hem tüm vücut titreşimi (4,8 m/s2) hem de gürültü maruziyetinin (89,3 dBA) yüksek olduğu görülmüştür. Fabrikadan alınan gürültü ölçüm değerlerinde ise S/T makinelerinin (90,6 dBA), ebatlama makinelerinden (85,5 dBA) daha fazla gürültüye yol açtıkları ortaya çıkmıştır. Elmas tel kesme makinesi kullanan çalışanların el-kol titreşimi ölçümlerinde elde edilen değerlerde her ne kadar günlük maruziyet sınır değeri olan 5 m/s2 değerinin aşılmadığı görülmüş ise de günlük maruziyet eylem değeri olan 2,5 m/s2’nin iki ocakta aşıldığı görülmüştür. Çalışmada son olarak, yapılan ölçümler sonucunda elde edilen verilerdeki sınır değerlerin üzerindeki değerlerle ilgili olarak ocaklar/fabrikada alınabilecek önlemler sunulmuştur.
- 5 July 2022
- Published by Politechnika Wroclawska Oficyna Wydawnicza in Physicochemical Problems of Mineral Processing
- Vol. 58 (5)
Modelling of selective retention of Cd-Ni ions from aqueous solutions by polymer enhanced ultrafiltration
Polymer enhanced ultrafiltration (PEUF) technique economically enables separation and/or retention of various heavy metal ions from aqueous solutions for environmental and engineering problems. Polyethylenimine as the water-soluble complexation agent utilized to interact with heavy metal ions of...
- 5 July 2022
- Published by Politechnika Wroclawska Oficyna Wydawnicza in Physicochemical Problems of Mineral Processing
- Vol. 58 (5)
Modelling of selective retention of Cd-Ni ions from aqueous solutions by polymer enhanced ultrafiltration
Polymer enhanced ultrafiltration (PEUF) technique economically enables separation and/or retention of various heavy metal ions from aqueous solutions for environmental and engineering problems. Polyethylenimine as the water-soluble complexation agent utilized to interact with heavy metal ions of...
- Open Access
- 1 March 2020
- Published by Hitit University in Hittite Journal of Science and Engineering
- Vol. 7 (1) , 01-06
08The Influence of Grinding Parameters of Talc on Water-Based Paint Properties: Application of Multivariate Regression Analysis
In this study, the influence of grinding parameters of talc sample in the conventional ballmill on water-based paint properties was investigated, and the results obtained from the experiments were statistically modeled. The regression analysis were designed to reveal the correlation between grinding parameters of the talc and the opacity and brightness of the paint with the recipes containing prepared mineral. In multivariate regression analysis, the differential grinding parameters were used to determine the change on opacity and brightness of the paint with a linear model between the change of the grinding parameters as the variables. Therefore, developed analysis includes a numerical model which could foresee the changes on final paint properties due to parameter changes (ball charge, material charge and time) in the grinding process. At the end of the experimental studies, the results indicated that the changes on brightness and opacity of a water-based paint are very dependant to the characteristics of talc mineral used as a filler in the same recipe. In other words, it was possible to foresee the changes on opacity and brightness of the paint due to changing grinding parameters of talc used as mineral filler in paint by using multivariate multiple regression analysis. Keywords: Talc, Grinding, Grinding parameters, Paint, Opacity (OP), Brightness (BR), Multivariate regression analysis (MRA), Modeling. DOI: 10.17350/HJSE19030000165 Full Text:
- 1 March 2020
- Published by Hitit University in Hittite Journal of Science and Engineering
- Vol. 7 (1) , 01-06
Open Access08The Influence of Grinding Parameters of Talc on Water-Based Paint Properties: Application of Multivariate Regression Analysis
In this study, the influence of grinding parameters of talc sample in the conventional ballmill on water-based paint properties was investigated, and the results obtained from the experiments were statistically modeled. The regression analysis were designed to reveal the correlation between grinding parameters of the talc and the opacity and brightness of the paint with the recipes containing prepared mineral. In multivariate regression analysis, the differential grinding parameters were used to determine the change on opacity and brightness of the paint with a linear model between the change of the grinding parameters as the variables. Therefore, developed analysis includes a numerical model which could foresee the changes on final paint properties due to parameter changes (ball charge, material charge and time) in the grinding process. At the end of the experimental studies, the results indicated that the changes on brightness and opacity of a water-based paint are very dependant to the characteristics of talc mineral used as a filler in the same recipe. In other words, it was possible to foresee the changes on opacity and brightness of the paint due to changing grinding parameters of talc used as mineral filler in paint by using multivariate multiple regression analysis. Keywords: Talc, Grinding, Grinding parameters, Paint, Opacity (OP), Brightness (BR), Multivariate regression analysis (MRA), Modeling. DOI: 10.17350/HJSE19030000165 Full Text:
- 23 May 2012
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 43 (5) , 366-372
Predicting the extent of hydrophilicity on Si nano‐column surfaces
- 23 May 2012
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 43 (5) , 366-372
Predicting the extent of hydrophilicity on Si nano‐column surfaces
- 18 April 2011
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 122 (1) , 19-28
Rheological, electrokinetic, and morphological characterization of alginate–bentonite biocomposites
We prepared biocomposite gel dispersions involving sodium alginate (Na‐Alg) and calcium bentonite (Ca‐B) with various solid concentrations and characterized their rheological, electrokinetic, and morphological properties. The flow properties, such as the apparent and plastic viscosities, shear stress, and yield value point, changed with increasing clay dosage. The viscosities of the homogeneous dispersions were represented by the Herschel–Bulkley model. The ζ‐potential results were examined in the light of different characterization methods (X‐ray diffraction, Fourier transform infrared spectroscopy, and atomic force microscopy) to understand the interactions between the Na and Ca ions of the alginate biopolymer and bentonite clay. A plausible structural model for the alginate–bentonite composite gel, known as the egg‐box model, is proposed. The presence of Ca ions in the Ca‐B partially crosslinked Na‐Alg may be regarded as an excellent example of a self‐assembling process. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.
- 18 April 2011
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 122 (1) , 19-28
Rheological, electrokinetic, and morphological characterization of alginate–bentonite biocomposites
We prepared biocomposite gel dispersions involving sodium alginate (Na‐Alg) and calcium bentonite (Ca‐B) with various solid concentrations and characterized their rheological, electrokinetic, and morphological properties. The flow properties, such as the apparent and plastic viscosities, shear stress, and yield value point, changed with increasing clay dosage. The viscosities of the homogeneous dispersions were represented by the Herschel–Bulkley model. The ζ‐potential results were examined in the light of different characterization methods (X‐ray diffraction, Fourier transform infrared spectroscopy, and atomic force microscopy) to understand the interactions between the Na and Ca ions of the alginate biopolymer and bentonite clay. A plausible structural model for the alginate–bentonite composite gel, known as the egg‐box model, is proposed. The presence of Ca ions in the Ca‐B partially crosslinked Na‐Alg may be regarded as an excellent example of a self‐assembling process. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.
- 1 February 2010
- Published by Elsevier in Applied Clay Science
- Vol. 47 (3-4) , 217-222
Determining the fiber size of nano structured sepiolite using Atomic Force Microscopy (AFM)
- 1 February 2010
- Published by Elsevier in Applied Clay Science
- Vol. 47 (3-4) , 217-222
Determining the fiber size of nano structured sepiolite using Atomic Force Microscopy (AFM)