Fatemeh Bahadori
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Fatemeh Bahadori has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Ahmad Taghizadeh Damanabi
Chemical Engineering Department, Urmia University of Technology, Urmia, Iran
3 shared publicationsAbolfazl Farajzadeh
Affiliation Chemical Engineering Department, Urmia University of Technology, Urmia, Iran
1 shared publicationAli Maleki
Faculty of Chemical Engineering, Urmia University of Technology, Urmia, Iran
1 shared publicationAli Mohammadnejad
1 shared publicationAlireza Azizi
Chemical Engineering Department,Urmia University of Technology,Urmia,IranTabriz Petrochemical Company,Tabriz,Iran
1 shared publicationArash Afghan
Department of Chemistry, Faculty of Renewable Energies, Urmia University of Technology, Urmia, Iran
1 shared publication
Latest Publications
- Open Access
- 9 February 2026
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 21 (2) , e0341023
Simulation of liquid hydrocarbon production via n-tetradecane reforming: A renewable energy approach
Considering the current worldwide search for renewable energy, n-tetradecane has attracted attention as a candidate for a hydrogen energy carrier and more sighted for light hydrocarbon within the gasoline range of C 5 -C 12 . This study investigates the production of liquid hydrocarbons by n-tetradecane in two stages process: syngas production through reforming of n-tetradecane and Fischer-Tropsch synthesis. The temperature, oxygen-to-carbon (O 2 /C) ratio, reactor length-to-diameter (L/D) ratio, and steam-to-carbon (S/C) ratio are examined in this study as the parameters that influence the reforming of n-tetradecane and superior result of 800ºC, 0.356 O 2 /C, 6 L/D and 2.3 S/C were established to give high conversion and efficient production of syngas. While the yield of the C 5 + hydrocarbon in the Fischer-Tropsch (FT) reactor increased with rising temperature up to 350°C, but the permissible temperature for process is 290°C, based on these, the temperature was set to optimize productivity and longevity of the catalyst. When using n-tetradecane as feed stock, high C 5 + production was resulted because of its suited H 2 /CO ratio of 2.3. The techno-economic assessment highlights the process’s viability at moderate scales, with economic performance strongly influenced by product price and energy integration.
- 9 February 2026
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 21 (2) , e0341023
Open AccessSimulation of liquid hydrocarbon production via n-tetradecane reforming: A renewable energy approach
Considering the current worldwide search for renewable energy, n-tetradecane has attracted attention as a candidate for a hydrogen energy carrier and more sighted for light hydrocarbon within the gasoline range of C 5 -C 12 . This study investigates the production of liquid hydrocarbons by n-tetradecane in two stages process: syngas production through reforming of n-tetradecane and Fischer-Tropsch synthesis. The temperature, oxygen-to-carbon (O 2 /C) ratio, reactor length-to-diameter (L/D) ratio, and steam-to-carbon (S/C) ratio are examined in this study as the parameters that influence the reforming of n-tetradecane and superior result of 800ºC, 0.356 O 2 /C, 6 L/D and 2.3 S/C were established to give high conversion and efficient production of syngas. While the yield of the C 5 + hydrocarbon in the Fischer-Tropsch (FT) reactor increased with rising temperature up to 350°C, but the permissible temperature for process is 290°C, based on these, the temperature was set to optimize productivity and longevity of the catalyst. When using n-tetradecane as feed stock, high C 5 + production was resulted because of its suited H 2 /CO ratio of 2.3. The techno-economic assessment highlights the process’s viability at moderate scales, with economic performance strongly influenced by product price and energy integration.
- 27 June 2025
- Published by Elsevier in Sustainable Chemistry and Pharmacy
- Vol. 46
Simulation and optimization of CO2 mineralization for sustainable cement production
- 27 June 2025
- Published by Elsevier in Sustainable Chemistry and Pharmacy
- Vol. 46
Simulation and optimization of CO2 mineralization for sustainable cement production
- Open Access
- 22 June 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-7
Carbon dioxide utilization in propylene carbonate production process
Utilizing carbon dioxide in chemical processes is one of the suggested remedies for reducing its atmospheric concentration. In this paper, the simulation of the propylene carbonate production process using 1,2-propanediol and carbon dioxide has been performed. The impact of temperature was examined between 75 and 400°C. It has been found that as temperature rises, reaction conversion increases. Additionally, the impact of recycling ratio was examined in the range of 0.1–0.5, which demonstrates that a rise in the recycle ratio results in a fall in conversion. Furthermore; it was observed that the pressure initially increases the solubility of carbon dioxide in 1,2-propanediol and improves the conversion of the reaction, but when enough carbon dioxide is supplied in the reaction, increasing the pressure does not affect the corresponding reaction. The effect of all studied parameters depends on the residence time of the reactants in the reactor. Investigating the interaction of parameters and optimizing the process has shown several optimal point of the process such as temperature of 295 °C, a recycle ratio 0.1, feed ratio 0.8 and a residence time of 12.61 h, with the related conversion being 59.6%.
- 22 June 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-7
Open AccessCarbon dioxide utilization in propylene carbonate production process
Utilizing carbon dioxide in chemical processes is one of the suggested remedies for reducing its atmospheric concentration. In this paper, the simulation of the propylene carbonate production process using 1,2-propanediol and carbon dioxide has been performed. The impact of temperature was examined between 75 and 400°C. It has been found that as temperature rises, reaction conversion increases. Additionally, the impact of recycling ratio was examined in the range of 0.1–0.5, which demonstrates that a rise in the recycle ratio results in a fall in conversion. Furthermore; it was observed that the pressure initially increases the solubility of carbon dioxide in 1,2-propanediol and improves the conversion of the reaction, but when enough carbon dioxide is supplied in the reaction, increasing the pressure does not affect the corresponding reaction. The effect of all studied parameters depends on the residence time of the reactants in the reactor. Investigating the interaction of parameters and optimizing the process has shown several optimal point of the process such as temperature of 295 °C, a recycle ratio 0.1, feed ratio 0.8 and a residence time of 12.61 h, with the related conversion being 59.6%.
- Open Access
- 6 October 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-7
Simulation and multi-objective optimization of the dimethyl carbonate production process
Greenhouse gases such as CO2 are considered effective materials in global warming due to their high absorptivity. So, lowering atmospheric CO2 is one of the most practical strategies. Utilizing carbon dioxide in chemical processes is an applicable method. In this study, Aspen HYSYS 10 was used to investigate how carbon dioxide can be added to the process of dimethyl carbonate production, and the affective parameters of the process, including temperature, residence time, feed ratio, and recycle ratio, were evaluated. It was observed that the production of DMC grew as temperature rose. The simulation results also revealed that a maximum conversion of roughly 8% was attained in the MeOH/EC. Additionally, boosting the recycle ratio is detrimental, and the impact of temperature and MeOH/EC has been enhanced by increasing the residence time. The interactions of the above parameters have been studied by Design Expert 12. The optimum value of effective parameters for the production of dimethyl carbonate has been obtained as follows: temperature of 164.7° C, recycle ratio of 0.2, residence time of 139.45 min, and feed ratio of 5.9%, leading to the conversion of 70%.
- 6 October 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-7
Open AccessSimulation and multi-objective optimization of the dimethyl carbonate production process
Greenhouse gases such as CO2 are considered effective materials in global warming due to their high absorptivity. So, lowering atmospheric CO2 is one of the most practical strategies. Utilizing carbon dioxide in chemical processes is an applicable method. In this study, Aspen HYSYS 10 was used to investigate how carbon dioxide can be added to the process of dimethyl carbonate production, and the affective parameters of the process, including temperature, residence time, feed ratio, and recycle ratio, were evaluated. It was observed that the production of DMC grew as temperature rose. The simulation results also revealed that a maximum conversion of roughly 8% was attained in the MeOH/EC. Additionally, boosting the recycle ratio is detrimental, and the impact of temperature and MeOH/EC has been enhanced by increasing the residence time. The interactions of the above parameters have been studied by Design Expert 12. The optimum value of effective parameters for the production of dimethyl carbonate has been obtained as follows: temperature of 164.7° C, recycle ratio of 0.2, residence time of 139.45 min, and feed ratio of 5.9%, leading to the conversion of 70%.
- 21 September 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (48) , 106636-106647
Investigation of optimal operating conditions in dimethyl ether carbonylation to methyl acetate production process
Ethanol production methods are expanding due to the importance of ethanol as a fuel or additive to fuels. One of these methods is converting methanol to ethanol in a three-step process. All of these steps need to deeply study and investigate to develop the process. In this research, the carbonylation of dimethyl ether to produce methyl acetate, which is the intermediate reaction of the three-step process of methanol to ethanol, has been simulated and optimized. The parameters of temperature, pressure, residence time, and feed ratio have been investigated as effective operational parameters of the process. It has been shown that the temperature and pressure of the process are more effective in the ranges of 220–280 °C and 30–50 bar, respectively. The simulation results showed a maximum point in dimethyl ether conversion in the feed ratio of 0.4–0.6, i.e., in temperature of 260 °C, residence time of 5 h, pressure of 45 bar, DME/CO/Ar = 30/67/3, and DME conversion about 22%. Also, it has been shown that increasing the residence time increases the effect of each of the above parameters. Optimization of the dimethyl ether carbonylation process has demonstrated that the combination of different ranges of the above parameters achieves the desired conversion, i.e., in pressure of 48.23 bar, temperature of 259.06 °C, residence time of 3.68 h, and dimethyl ether/feed of 0.461 vol%; conversion of dimethyl ether will be equal to 85.50%.
- 21 September 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (48) , 106636-106647
Investigation of optimal operating conditions in dimethyl ether carbonylation to methyl acetate production process
Ethanol production methods are expanding due to the importance of ethanol as a fuel or additive to fuels. One of these methods is converting methanol to ethanol in a three-step process. All of these steps need to deeply study and investigate to develop the process. In this research, the carbonylation of dimethyl ether to produce methyl acetate, which is the intermediate reaction of the three-step process of methanol to ethanol, has been simulated and optimized. The parameters of temperature, pressure, residence time, and feed ratio have been investigated as effective operational parameters of the process. It has been shown that the temperature and pressure of the process are more effective in the ranges of 220–280 °C and 30–50 bar, respectively. The simulation results showed a maximum point in dimethyl ether conversion in the feed ratio of 0.4–0.6, i.e., in temperature of 260 °C, residence time of 5 h, pressure of 45 bar, DME/CO/Ar = 30/67/3, and DME conversion about 22%. Also, it has been shown that increasing the residence time increases the effect of each of the above parameters. Optimization of the dimethyl ether carbonylation process has demonstrated that the combination of different ranges of the above parameters achieves the desired conversion, i.e., in pressure of 48.23 bar, temperature of 259.06 °C, residence time of 3.68 h, and dimethyl ether/feed of 0.461 vol%; conversion of dimethyl ether will be equal to 85.50%.
- 13 June 2023
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 42 (25) , 4444-4461
Enhancing the production of liquid hydrocarbons by coupling blast furnace gas (BFG) of steelwork with syngas in the GTL process
- 13 June 2023
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 42 (25) , 4444-4461
Enhancing the production of liquid hydrocarbons by coupling blast furnace gas (BFG) of steelwork with syngas in the GTL process
- 23 April 2023
- Published by Springer Nature in Clean Technologies and Environmental Policy
- Vol. 25 (8) , 2777-2788
Simulation and multi-objective optimization of liquid hydrocarbons production by coupling Blast Furnace Gas with Coke Oven Gas of steelwork
- 23 April 2023
- Published by Springer Nature in Clean Technologies and Environmental Policy
- Vol. 25 (8) , 2777-2788
Simulation and multi-objective optimization of liquid hydrocarbons production by coupling Blast Furnace Gas with Coke Oven Gas of steelwork
- Open Access
- 31 January 2023
- Published by University of Chemical Technology and Metallurgy in Journal of Chemical Technology and Metallurgy
- Vol. 58 (3) , 522-528
Simulation of pollutants dispersion by a stack: А case study
The rapid growth of urbanization and industrialization cause the world face with the most important environmental issues of air pollution in many cities and industrial zones. In the present research, air pollution due to the emission of pollutants air quality is studied. Emission and dispersion of NOx from a stack located in an industrial zone are simulated based on the meteorological data. The geometry of the stack and surrounding area are selected from a power plant data. The analysis is individually performed for four seasons using the wind field and direction. It is shown that wind direction significantly affects the pollutants circulation zone. The pollutants inversion are unpreventable occurred in winter because of the mixing area is not well altitudinal extended.
- 31 January 2023
- Published by University of Chemical Technology and Metallurgy in Journal of Chemical Technology and Metallurgy
- Vol. 58 (3) , 522-528
Open AccessSimulation of pollutants dispersion by a stack: А case study
The rapid growth of urbanization and industrialization cause the world face with the most important environmental issues of air pollution in many cities and industrial zones. In the present research, air pollution due to the emission of pollutants air quality is studied. Emission and dispersion of NOx from a stack located in an industrial zone are simulated based on the meteorological data. The geometry of the stack and surrounding area are selected from a power plant data. The analysis is individually performed for four seasons using the wind field and direction. It is shown that wind direction significantly affects the pollutants circulation zone. The pollutants inversion are unpreventable occurred in winter because of the mixing area is not well altitudinal extended.