Petr Kabele
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Petr Kabele has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Jiří Žák
Institute of Geology and Paleontology, Faculty of Science, Charles University, Prague, Czech Republic
4 shared publications Byung H. Oh
Seoul National University
2 shared publications- Gideon P. A. G. van Zijl
Stellenbosch University
2 shared publications Hideyuki Horii
The University of Tokyo
2 shared publicationsJ. Nemecek
2 shared publicationsMichal Přinosil
Czech Technical University in Prague
2 shared publications
Latest Publications
- Open Access
Inverse analysis of traction-separation relationship based on sequentially linear approach
Traction-separation relationship is an important material characteristic describing the fracture behaviour of quasi-brittle solids. A new numerical scheme for identification of the traction-separation relation by inverse analysis of data obtained from various types of fracture tests is proposed. Due to employing the concept of sequentially linear analysis, the method exhibits a superior numerical stability and versatility. The applicability and effectiveness of the proposed method is demonstrated on examples involving identification of the traction-separation relationship using experimental data from various test configurations.
Open AccessInverse analysis of traction-separation relationship based on sequentially linear approach
Traction-separation relationship is an important material characteristic describing the fracture behaviour of quasi-brittle solids. A new numerical scheme for identification of the traction-separation relation by inverse analysis of data obtained from various types of fracture tests is proposed. Due to employing the concept of sequentially linear analysis, the method exhibits a superior numerical stability and versatility. The applicability and effectiveness of the proposed method is demonstrated on examples involving identification of the traction-separation relationship using experimental data from various test configurations.
- 6 January 2017
- Published by Springer Nature
- p. 79-100
Chemical Processes
- 19 February 2016
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 825, 165-169
Influence of the Bell-Jar Magma Chamber Geometry on a Caldera Formation
The formation of a caldera poses a serious risk for the society and the environment. There are several established processes (mostly dealing with the conditions inside the reservoir), which must take place in order to reach a collapse leading to the caldera. The role of magma chamber geometry is investigated in this paper, exploiting the numerical modeling. The results indicates that the knowledge of the magmatic system dimensions can provide a helpful factor for an assessment of the caldera formation scenario.
- 19 February 2016
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 825, 165-169
Influence of the Bell-Jar Magma Chamber Geometry on a Caldera Formation
The formation of a caldera poses a serious risk for the society and the environment. There are several established processes (mostly dealing with the conditions inside the reservoir), which must take place in order to reach a collapse leading to the caldera. The role of magma chamber geometry is investigated in this paper, exploiting the numerical modeling. The results indicates that the knowledge of the magmatic system dimensions can provide a helpful factor for an assessment of the caldera formation scenario.
- 19 February 2016
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 825, 161-164
Analysis of Stability of Mode II Crack Growth
As the previous part of authors ́ research deals with numerical modelling of functionally graded members in general, the following part is focused on analysis of the interface between individual layers. For correct description of interface behavior in numerical simulations, interface model parameters must be determined by appropriate physical tests. Testing methods for the tensile properties are known while the shear tests may face some difficulties. Shear test configurations for measuring interface behavior after the peak which is related to the stable crack growth along the interface are analyzed. The subject of presented paper is to evaluate tests in terms of stable mode II crack growth along the interface. Stable crack growth is assessed by stress intensity factor and finite element method.
- 19 February 2016
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 825, 161-164
Analysis of Stability of Mode II Crack Growth
As the previous part of authors ́ research deals with numerical modelling of functionally graded members in general, the following part is focused on analysis of the interface between individual layers. For correct description of interface behavior in numerical simulations, interface model parameters must be determined by appropriate physical tests. Testing methods for the tensile properties are known while the shear tests may face some difficulties. Shear test configurations for measuring interface behavior after the peak which is related to the stable crack growth along the interface are analyzed. The subject of presented paper is to evaluate tests in terms of stable mode II crack growth along the interface. Stable crack growth is assessed by stress intensity factor and finite element method.
- 1 January 2016
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 821, 526-531
Mechanical Properties of Fiber Reinforced Lime-Based Mortars Evaluated from Four-Point Bending Test
In the study, the bending behavior of high-performance fiber reinforced lime-based mortars is experimentally investigated using four-point bending test. From the experimental data, the influence of the mortar’s composition on its stiffness, cracking strength and ultimate strength are investigated. It is also studied, whether the response has strain-softening or strain-hardening character and whether the material exhibits multiple cracking. Such behavior is very important for the durability of the material, because it allows carrying load during imposed deformations (due to thermal effects, movements of foundations, seismicity, etc.). The number of formed cracks is examined using digital image correlation method. The mortar composition is considered with two types of binder (pure lime, lime-metakaolin), with two types of polyvinyl alcohol fibers in four volume fractions (0.5÷2.0%). As the reference, we consider two sets of specimens made of plain mortar without fiber reinforcement.
- 1 January 2016
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 821, 526-531
Mechanical Properties of Fiber Reinforced Lime-Based Mortars Evaluated from Four-Point Bending Test
In the study, the bending behavior of high-performance fiber reinforced lime-based mortars is experimentally investigated using four-point bending test. From the experimental data, the influence of the mortar’s composition on its stiffness, cracking strength and ultimate strength are investigated. It is also studied, whether the response has strain-softening or strain-hardening character and whether the material exhibits multiple cracking. Such behavior is very important for the durability of the material, because it allows carrying load during imposed deformations (due to thermal effects, movements of foundations, seismicity, etc.). The number of formed cracks is examined using digital image correlation method. The mortar composition is considered with two types of binder (pure lime, lime-metakaolin), with two types of polyvinyl alcohol fibers in four volume fractions (0.5÷2.0%). As the reference, we consider two sets of specimens made of plain mortar without fiber reinforcement.
- 1 August 2015
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 784, 137-144
Constitutive Model for Timber Fracture under Tensile and Shear Loads
A 2D homogeneous orthotropic constitutive model of tensile and shear fracture in timber based on fixed smeared crack approach has been developed and implemented in ATENA®finite element software. The model captures (1) elastic and inelastic behavior in small deformations range, (2) material orthotropy, both in linear and non-linear range, (3) cracking across or along fibers, and (4) behavior under unloading/reloading. In this contribution we present model validation through numerical simulations of compact tension shear (CTS) tests of Radiata Pine timber.
- 1 August 2015
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 784, 137-144
Constitutive Model for Timber Fracture under Tensile and Shear Loads
A 2D homogeneous orthotropic constitutive model of tensile and shear fracture in timber based on fixed smeared crack approach has been developed and implemented in ATENA®finite element software. The model captures (1) elastic and inelastic behavior in small deformations range, (2) material orthotropy, both in linear and non-linear range, (3) cracking across or along fibers, and (4) behavior under unloading/reloading. In this contribution we present model validation through numerical simulations of compact tension shear (CTS) tests of Radiata Pine timber.
- Open Access
- 30 June 2015
- Published by Japan Concrete Institute in Journal of Advanced Concrete Technology
- Vol. 13 (6) , 311-324
Modeling of High-Strength FRC Structural Elements with Spatially Non-Uniform Fiber Volume Fraction
The research presented in this paper has been motivated by the need to numerically simulate performance of high strength fiber reinforced concrete (HSFRC) structural elements with given spatially variable fiber volume fraction. The intended applications include prediction of load and deformation capacity of HSFRC members with imperfect fiber distribution or design and verification of functionally graded HSFRC members. In order to achieve a predictive capability, modeling is based on micromechanics of fiber debonding, pullout and crack-bridging. The concept of cohesive crack is employed for implementation in the finite element method (FEM). A strong emphasis is placed on the feasibility of the model identification. To this end, a procedure which uses data from conventional notched-beam fracture tests and inverse analysis to determine the model parameters is proposed. The model and the identification method are verified and validated both on micro and macro scales by comparing predicted results with experimental data.
- 30 June 2015
- Published by Japan Concrete Institute in Journal of Advanced Concrete Technology
- Vol. 13 (6) , 311-324
Open AccessModeling of High-Strength FRC Structural Elements with Spatially Non-Uniform Fiber Volume Fraction
The research presented in this paper has been motivated by the need to numerically simulate performance of high strength fiber reinforced concrete (HSFRC) structural elements with given spatially variable fiber volume fraction. The intended applications include prediction of load and deformation capacity of HSFRC members with imperfect fiber distribution or design and verification of functionally graded HSFRC members. In order to achieve a predictive capability, modeling is based on micromechanics of fiber debonding, pullout and crack-bridging. The concept of cohesive crack is employed for implementation in the finite element method (FEM). A strong emphasis is placed on the feasibility of the model identification. To this end, a procedure which uses data from conventional notched-beam fracture tests and inverse analysis to determine the model parameters is proposed. The model and the identification method are verified and validated both on micro and macro scales by comparing predicted results with experimental data.
- 1 September 2014
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 624, 246-253
Numerical Analysis of Masonry Enhanced by Fiber Reinforced Lime-Based Render
Out of plane load bearing capacity of a masonry structure enhanced by surface render made of high performance lime-based mortar is investigated by numerical simulations using the finite element method (FEM). The response of the wall is simulated firstly without render (as a reference) then with surface render consisting of conventional lime mortar with increased tensile strength (by addition of the metakaolin) without fibers and finally with the proposed lime-metakaolin mortar reinforced with PVA fibers. The thickness of the surface render is considered in two configurations (20 mm and 40 mm). Material parameters of masonry units (bricks), joints (mortar between bricks) and conventional plain render are chosen with regard to investigations of historic structures (reported in the literature), material characteristics of fiber reinforced render are evaluated based on experiments or numerical simulations of these experiments. Using these parameters and characteristics, the numerical simulations of masonry wall subjected to out of plane bending are performed. The results allow us to identify influence of the thickness and the material of render on load-bearing and deformation capacity, failure mode and amount and width of cracks. The results show that the conventional plain mortar improves load-bearing capacity and deformation capacity proportionately to the thickness of render, but the response remains brittle. Fiber reinforced mortar significantly increases the deformation capacity and load-bearing capacity and the amount of absorbed energy is significantly improved.
- 1 September 2014
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 624, 246-253
Numerical Analysis of Masonry Enhanced by Fiber Reinforced Lime-Based Render
Out of plane load bearing capacity of a masonry structure enhanced by surface render made of high performance lime-based mortar is investigated by numerical simulations using the finite element method (FEM). The response of the wall is simulated firstly without render (as a reference) then with surface render consisting of conventional lime mortar with increased tensile strength (by addition of the metakaolin) without fibers and finally with the proposed lime-metakaolin mortar reinforced with PVA fibers. The thickness of the surface render is considered in two configurations (20 mm and 40 mm). Material parameters of masonry units (bricks), joints (mortar between bricks) and conventional plain render are chosen with regard to investigations of historic structures (reported in the literature), material characteristics of fiber reinforced render are evaluated based on experiments or numerical simulations of these experiments. Using these parameters and characteristics, the numerical simulations of masonry wall subjected to out of plane bending are performed. The results allow us to identify influence of the thickness and the material of render on load-bearing and deformation capacity, failure mode and amount and width of cracks. The results show that the conventional plain mortar improves load-bearing capacity and deformation capacity proportionately to the thickness of render, but the response remains brittle. Fiber reinforced mortar significantly increases the deformation capacity and load-bearing capacity and the amount of absorbed energy is significantly improved.
- 1 January 2013
- Published by Springer Nature
Strain Hardening Cement Composites: Structural Design and Performance
- 1 January 2013
- Published by Springer Nature
Strain Hardening Cement Composites: Structural Design and Performance
- 1 March 2012
- Published by Elsevier in Journal of Structural Geology
- Vol. 36, 27-42
Magmatic to solid state fabrics in syntectonic granitoids recording early Carboniferous orogenic collapse in the Bohemian Massif
- 1 March 2012
- Published by Elsevier in Journal of Structural Geology
- Vol. 36, 27-42
Magmatic to solid state fabrics in syntectonic granitoids recording early Carboniferous orogenic collapse in the Bohemian Massif