Yong-Cheol Kang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yong-Cheol Kang has a total of 101 co-authors. Here are the top co-authors by number of shared publications:
Juyun Park
24 shared publicationsJisoo Kang
Department of Physics and Astronomy University of Pennsylvania 209 S. 33rd St. Philadelphia PA 19104 USA
6 shared publicationsDonghyun Kim
Department of Chemistry Pukyong National University 45 Yongso‐ro Nam‐Gu Busan 48513 Korea
5 shared publications- Jin-Woo Oh
Department of Nano Fusion Technology Pusan National University Busan 46241 Republic of Korea
5 shared publications Jihyeon Lee
Department of Chemistry Pukyong National University 45 Yongso‐ro Nam‐Gu Busan 48513 Korea
4 shared publicationsJin-Woo Oh
Department of Nanoenergy Engineering Pusan National University Busandaehak-ro 63 Beon-gil 2, Geumjeong-gu Busan 46241 South Korea
4 shared publications
Latest Publications
- Open Access
Post-Annealing Effect on the Physicochemical Properties of Sn-Te-O Thin Films
This study explores how post-deposition thermal annealing alters the structural, morphological, and electronic properties of Sn–Te–O thin films grown by radio-frequency magnetron co-sputtering. Thin films were annealed at temperatures ranging from 298 K to 873 K and analyzed using a suite of techniques, including X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and atomic force microscopy (AFM). Annealing at 473 K resulted in increased surface roughness (Rq) in Te-rich films, while higher annealing temperatures promoted a chemical shift in tin oxidation states from Sn2+ to Sn4+. XRD patterns of films annealed at 473 K revealed the emergence of cubic-phase SnTe reflections not prominent in unannealed samples. Contact angle measurements indicated enhanced wettability in high-Te films after annealing, and work function analysis via Kelvin probe showed a trend of decreasing surface potential with lower Te content. These results provide insight into the thermal oxidation behavior and surface evolution of SnTe films, relevant for thermoelectric and topological applications.
Open AccessPost-Annealing Effect on the Physicochemical Properties of Sn-Te-O Thin Films
This study explores how post-deposition thermal annealing alters the structural, morphological, and electronic properties of Sn–Te–O thin films grown by radio-frequency magnetron co-sputtering. Thin films were annealed at temperatures ranging from 298 K to 873 K and analyzed using a suite of techniques, including X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and atomic force microscopy (AFM). Annealing at 473 K resulted in increased surface roughness (Rq) in Te-rich films, while higher annealing temperatures promoted a chemical shift in tin oxidation states from Sn2+ to Sn4+. XRD patterns of films annealed at 473 K revealed the emergence of cubic-phase SnTe reflections not prominent in unannealed samples. Contact angle measurements indicated enhanced wettability in high-Te films after annealing, and work function analysis via Kelvin probe showed a trend of decreasing surface potential with lower Te content. These results provide insight into the thermal oxidation behavior and surface evolution of SnTe films, relevant for thermoelectric and topological applications.
- 25 January 2025
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 701
Surface properties of copper oxytelluride thin films with different composition ratios fabricated by RF magnetron co-sputtering
- 25 January 2025
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 701
Surface properties of copper oxytelluride thin films with different composition ratios fabricated by RF magnetron co-sputtering
- 29 October 2024
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (4)
Investigation on the Surface Properties of Annealed Copper Selenide Thin Films with Various Compositional Ratios
Copper‐based metal chalcogenides are versatile materials used for a variety of electronic devices, yet realizing the full scope of copper‐based composite materials is hindered by limited understanding of their chemical properties. In this work, copper selenide thin films (TFs) are fabricated using radio frequency (RF) magnetron co‐sputtering to investigate the effects of composition and annealing temperature on the films. The surface composition of the TFs is examined using energy dispersive X‐Ray spectroscopy (EDS) and X‐Ray photoelectron spectroscopy (XPS). In the unannealed films, an increase in Se composition leads to smaller grain sizes and smoother surfaces. The influence of higher Se content on the dispersive surface free energy (SFE) is shown through contact angle measurements. Work functions (WFs), determined by Kelvin probe (KP) and ultraviolet photoelectron spectroscopy (UPS), rose with increasing Se content. After annealing, the TFs exhibited opposite trends. As the films transitioned from an amorphous to a crystalline phase due to annealing, their roughness significantly increased.
- 29 October 2024
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (4)
Investigation on the Surface Properties of Annealed Copper Selenide Thin Films with Various Compositional Ratios
Copper‐based metal chalcogenides are versatile materials used for a variety of electronic devices, yet realizing the full scope of copper‐based composite materials is hindered by limited understanding of their chemical properties. In this work, copper selenide thin films (TFs) are fabricated using radio frequency (RF) magnetron co‐sputtering to investigate the effects of composition and annealing temperature on the films. The surface composition of the TFs is examined using energy dispersive X‐Ray spectroscopy (EDS) and X‐Ray photoelectron spectroscopy (XPS). In the unannealed films, an increase in Se composition leads to smaller grain sizes and smoother surfaces. The influence of higher Se content on the dispersive surface free energy (SFE) is shown through contact angle measurements. Work functions (WFs), determined by Kelvin probe (KP) and ultraviolet photoelectron spectroscopy (UPS), rose with increasing Se content. After annealing, the TFs exhibited opposite trends. As the films transitioned from an amorphous to a crystalline phase due to annealing, their roughness significantly increased.
- Open Access
Etching and Compositional Ratio Effect on the Surface Properties of Bismuth Telluride Thin Films
Bismuth telluride has garnered considerable attention owing to its versatile properties applicable in thermoelectric and antibacterial domains, as well as its intriguing topological insulating properties. In this work, our group fabricated bismuth telluride thin films with various ratios using radio frequency magnetron sputtering. The surface properties of these thin films were thoroughly analyzed by employing a diverse array of analytical techniques, including X-ray photoelectron spectroscopy (XPS), ultraviolet photoelectron spectroscopy (UPS), scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction (XRD), four-point probe and contact angle (CA) measurements. Specifically, our XPS findings indicated that Bi is more susceptible to oxidation than Te following Ar+-ion etching. Pure Te thin films exhibited the highest Rq value of 31.2 nm based on AFM and SEM results due to their larger grain sizes. The XRD patterns revealed a peak at 27.75° for thin films with 20% Te, attributed to its rhombohedral structure. Moreover, thin films with 30% Te yielded the highest weighted average work function with a value of 4.95 eV after etching. Additionally, pristine Bi and Te thin films demonstrated the most robust hydrophobic properties compared to intermediate-composition thin films, as determined by CA measurements.
Open AccessEtching and Compositional Ratio Effect on the Surface Properties of Bismuth Telluride Thin Films
Bismuth telluride has garnered considerable attention owing to its versatile properties applicable in thermoelectric and antibacterial domains, as well as its intriguing topological insulating properties. In this work, our group fabricated bismuth telluride thin films with various ratios using radio frequency magnetron sputtering. The surface properties of these thin films were thoroughly analyzed by employing a diverse array of analytical techniques, including X-ray photoelectron spectroscopy (XPS), ultraviolet photoelectron spectroscopy (UPS), scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction (XRD), four-point probe and contact angle (CA) measurements. Specifically, our XPS findings indicated that Bi is more susceptible to oxidation than Te following Ar+-ion etching. Pure Te thin films exhibited the highest Rq value of 31.2 nm based on AFM and SEM results due to their larger grain sizes. The XRD patterns revealed a peak at 27.75° for thin films with 20% Te, attributed to its rhombohedral structure. Moreover, thin films with 30% Te yielded the highest weighted average work function with a value of 4.95 eV after etching. Additionally, pristine Bi and Te thin films demonstrated the most robust hydrophobic properties compared to intermediate-composition thin films, as determined by CA measurements.
- 29 January 2024
- Published by Wiley in Surface and Interface Analysis
- Vol. 56 (4) , 221-229
Tailoring the surface properties of molybdenum oxytelluride thin films by its compositional ratio
In this work, RF magnetron co‐sputtering was used to fabricate molybdenum oxytelluride thin films with different atomic ratios. Scanning electron micrographs and atomic force micrographs revealed that pure Mo thin films were segregated. Thin films with 40% Te content portrayed needle‐like structures and thus had the largest R q value of 2.48 nm. Contact angle measurements further supported the findings as the thin films with 40% Te content were the most hydrophobic. X‐ray photoelectron spectroscopy results revealed that the major oxidation states of Mo from Te‐poor to Te‐rich TFs were changed from high (+6) to low (+4 and/or +2). X‐ray diffraction data showed that peaks pertaining to molybdenum oxide species appeared, notably at 33.048° and 33.115°. Ultraviolet photoelectron spectroscopy and Kelvin probe measurements evinced that the work function increases with increasing Te content. Four‐point probe measurements revealed that molybdenum oxytelluride thin films tend to have higher electrical conductivity than pure Mo and Te thin films.
- 29 January 2024
- Published by Wiley in Surface and Interface Analysis
- Vol. 56 (4) , 221-229
Tailoring the surface properties of molybdenum oxytelluride thin films by its compositional ratio
In this work, RF magnetron co‐sputtering was used to fabricate molybdenum oxytelluride thin films with different atomic ratios. Scanning electron micrographs and atomic force micrographs revealed that pure Mo thin films were segregated. Thin films with 40% Te content portrayed needle‐like structures and thus had the largest R q value of 2.48 nm. Contact angle measurements further supported the findings as the thin films with 40% Te content were the most hydrophobic. X‐ray photoelectron spectroscopy results revealed that the major oxidation states of Mo from Te‐poor to Te‐rich TFs were changed from high (+6) to low (+4 and/or +2). X‐ray diffraction data showed that peaks pertaining to molybdenum oxide species appeared, notably at 33.048° and 33.115°. Ultraviolet photoelectron spectroscopy and Kelvin probe measurements evinced that the work function increases with increasing Te content. Four‐point probe measurements revealed that molybdenum oxytelluride thin films tend to have higher electrical conductivity than pure Mo and Te thin films.
- 15 October 2023
- Published by Wiley in Physica Status Solidi (a)
- Vol. 220 (21)
Annealing Temperature Effect on the Surface Properties of the MoSe Thin Films
2D transition metal dichalcogenides have been studied extensively in the field of electronics and photonics. Among them, the molybdenum chalcogenides have been receiving considerable attention due to their potential usage in field‐effect transistors and biosensors. Despite such promising aspects of these materials, studies regarding temperature effects on MoSe remain relatively rare. Herein, MoxSey (x = 0 ≈ 10, y = 0 ≈ 2) thin films are fabricated by radio frequency (RF) magnetron cosputtering on silicon and investigated using scanning electron microscopy for various atomic ratios and annealing temperatures from room temperature to 500 °C. Above the melting point of Se, Se evaporates and forms a layer, subsequently leading Mo to be exposed on the surface of the thin films. From the X‐ray diffraction and X‐ray photoelectron spectroscopy results, silicon peaks are observed due to the evaporation of Se. In addition, both Mo and Se are oxidized at above 300 °C. The work functions of the MoxSey thin films show the highest value at 200 °C measured by ultraviolet photoelectron spectroscopy and a Kelvin probe. Above the melting point of Se, there is a tendency for the work function to decrease due to the influence of Mo.
- 15 October 2023
- Published by Wiley in Physica Status Solidi (a)
- Vol. 220 (21)
Annealing Temperature Effect on the Surface Properties of the MoSe Thin Films
2D transition metal dichalcogenides have been studied extensively in the field of electronics and photonics. Among them, the molybdenum chalcogenides have been receiving considerable attention due to their potential usage in field‐effect transistors and biosensors. Despite such promising aspects of these materials, studies regarding temperature effects on MoSe remain relatively rare. Herein, MoxSey (x = 0 ≈ 10, y = 0 ≈ 2) thin films are fabricated by radio frequency (RF) magnetron cosputtering on silicon and investigated using scanning electron microscopy for various atomic ratios and annealing temperatures from room temperature to 500 °C. Above the melting point of Se, Se evaporates and forms a layer, subsequently leading Mo to be exposed on the surface of the thin films. From the X‐ray diffraction and X‐ray photoelectron spectroscopy results, silicon peaks are observed due to the evaporation of Se. In addition, both Mo and Se are oxidized at above 300 °C. The work functions of the MoxSey thin films show the highest value at 200 °C measured by ultraviolet photoelectron spectroscopy and a Kelvin probe. Above the melting point of Se, there is a tendency for the work function to decrease due to the influence of Mo.
- 11 May 2022
- Published by Elsevier in Thin Solid Films
- Vol. 753
Annealing temperature effect on the surface properties and antimicrobial activity of SnSe thin films
- 11 May 2022
- Published by Elsevier in Thin Solid Films
- Vol. 753
Annealing temperature effect on the surface properties and antimicrobial activity of SnSe thin films
- 12 April 2022
- Published by Wiley in Physica Status Solidi (a)
- Vol. 219 (12)
Physicochemical Properties of SnTe Thin Films Dependent on Compositional Ratios
This study introduces physicochemical properties based on the compositional ratio of the SnTe thin films (TFs) fabricated by radio frequency (RF) magnetron cosputtering. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) results show that the grain sizes decrease with increasing Te content, with pure Te TFs yielding the lowest Rq value (root mean square value of roughness) of 0.76 nm. Contact angle (CA) measurements show that pure Te TFs pertain to the highest total surface free energy. X‐Ray diffraction (XRD) patterns strongly indicate that pure Te TFs exhibit a hexagonal crystal structure and pure Sn TFs exhibit a tetragonal crystal structure. The dominant oxide species on the surface is TeO2 for Te‐rich films, which is deduced by X‐Ray photoelectron spectroscopy (XPS) results. Pure Te TFs yield a work function value of 4.88 eV when measured with ultraviolet photoelectron spectroscopy (UPS) and 5.46 eV when measured with a Kelvin probe. SnTe TFs with 70% Te content exhibit the lowest electrical conductivity among the fabricated TFs.
- 12 April 2022
- Published by Wiley in Physica Status Solidi (a)
- Vol. 219 (12)
Physicochemical Properties of SnTe Thin Films Dependent on Compositional Ratios
This study introduces physicochemical properties based on the compositional ratio of the SnTe thin films (TFs) fabricated by radio frequency (RF) magnetron cosputtering. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) results show that the grain sizes decrease with increasing Te content, with pure Te TFs yielding the lowest Rq value (root mean square value of roughness) of 0.76 nm. Contact angle (CA) measurements show that pure Te TFs pertain to the highest total surface free energy. X‐Ray diffraction (XRD) patterns strongly indicate that pure Te TFs exhibit a hexagonal crystal structure and pure Sn TFs exhibit a tetragonal crystal structure. The dominant oxide species on the surface is TeO2 for Te‐rich films, which is deduced by X‐Ray photoelectron spectroscopy (XPS) results. Pure Te TFs yield a work function value of 4.88 eV when measured with ultraviolet photoelectron spectroscopy (UPS) and 5.46 eV when measured with a Kelvin probe. SnTe TFs with 70% Te content exhibit the lowest electrical conductivity among the fabricated TFs.
- Open Access
- 6 August 2021
- Published by Wiley in Physica Status Solidi (a)
- Vol. 218 (15) , 2170043
Tailoring the Surface Characteristics of CuSe Thin Films by Adjusting the Compositional Ratio
- 6 August 2021
- Published by Wiley in Physica Status Solidi (a)
- Vol. 218 (15) , 2170043
Open AccessTailoring the Surface Characteristics of CuSe Thin Films by Adjusting the Compositional Ratio