SLSungwon Lee

Sungwon Lee

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Sungwon Lee has a total of 22 co-authors. Here are the top co-authors by number of shared publications:

  • Hoseong Shin

    SKKU Advanced Institute of Nano Technology (SAINT) Sungkyunkwan University 2066, Seobu‐ro, Jangan‐gu Suwon Gyeonggi‐do 16419 Republic of Korea

    2 shared publications
  • Won Jong Yoo

    Sungkyunkwan University

    2 shared publications
  • Byoung‐Hun Lee

    Department of Electrical Engineering Pohang University of Science and Technology (POSTECH) 77 Cheongam‐Ro, Nam‐Gu Pohang 37673 Republic of Korea

    1 shared publication
  • Byungdu Oh

    SKKU Advanced Institute of Nano Technology (SAINT) Sungkyunkwan University 2066, Seobu‐ro, Jangan‐gu Suwon Gyeonggi‐do 16419 Republic of Korea

    1 shared publication
  • Cihyun Kim

    Department of Electrical Engineering Pohang University of Science and Technology 77, Cheongam‐ro, Nam‐gu Pohang‐si Gyeongsangbuk‐do 37673 Republic of Korea

    1 shared publication
  • Duygu Gerceker

    Department of Chemical Engineering, Middle East Technical University, Ankara 06800, Turkey

    1 shared publication

Latest Publications

  • Self‐Powered 2D MoS2/WOx/WSe2 Heterojunction Photodetector Realized by Oxygen Plasma Treatment

    by Hoseong Shin, Muhammad Taqi, Fida Ali, Sungwon Lee, Min Sup Choi, Cihyun Kim, Byoung‐Hun Lee, Xiaochi Liu, Jian Sun, Byungdu Oh, et al.

    2D transition metal dichalcogenides (TMDCs) are anticipated to be the ones of future nano‐sized photodevices due to their electronic and optoelectronic properties. They have shown remarkable performances as photodetectors from being fabricated into heterostructures with p–n junction. An oxygen plasma‐doped WSe2/pristine MoS2‐based photodetector with high responsivity and broad detection spectrum ranging from visible to near‐infrared (NIR) region is reported. The oxygen plasma treatment forms a WOx layer on WSe2 that not only acts as a p‐dopant but also an interfacial oxide layer to suppress dark current to as low as ≈pA. Under illumination of visible light (520 nm in this study), greatly enhanced photoresponsivity and specific detectivity of thus fabricated devices are achieved without applying an external bias, in contrast to untreated devices. The devices have also exhibited good photodetection in the NIR region with two orders enhanced photoresponsivity under the illumination of 852 nm light at room temperature. It is confirmed from photomapping measurements that the photocurrent is mainly generated from p–n heterojunction. These results indicate that oxygen plasma‐doped WSe2‐based heterojunctions can be used as highly sensitive and self‐powered photodetectors.


  • Contact Resistivity in Edge‐Contacted Graphene Field Effect Transistors

    by Sungwon Lee, Hyungyu Choi, Inyong Moon, Hoseong Shin, Kenji Watanabe, Takashi Taniguchi, Won Jong Yoo

    A great challenge is presented when metals have contact with a 2D semiconducting material because the contact resistances (Rc) induced at the metal‐graphene interfaces hinder the performances of 2D devices, and therefore low resistance Ohmic contacts need to be developed to achieve unique and high performance of the 2D devices. This study demonstrates that edge‐contacted graphene devices of multiple stacked 2D hetero‐structures with hexagonal boron nitride (hBN) exhibit superior performances in carrier transport across channel and contact regions, compared to surface‐contacted devices. In surface‐contacted graphene devices, Rc and contact resistivity (ρc) are calculated by applying the modified transfer length (LT*) obtained from the contact‐end‐resistance method, while Rc and ρc in edge‐contacted graphene devices are estimated by replacing the LT* with the thickness of graphene. The edge‐contacted device is fabricated via a controlled plasma etching that allows each layer of graphene and hBN consisting hetero‐structures to be removed evenly at a uniform speed. Four‐point probe measurements are conducted in addition to transmission line method and confirms that ρc is lower for edge contact than surface contact. ρc of a graphene edge‐contacted device (≈10 Ω µm2) is much lower than that of a surface‐contacted device (≈230 Ω µm2).


  • In situ, operando studies on the size and structure of supported Pt catalysts under supercritical conditions by simultaneous synchrotron-based X-ray techniques

    by Sungwon Lee, Sungsik Lee, Duygu Gerceker, Mrunmayi D. Kumbhalkar, Kamila M. Wiaderek, Madelyn R. Ball, Manos Mavrikakis, James A. Dumesic, Randall E. Winans

    To control the size and structure of supported Pt catalysts, the influence of additional metal particles and the effect of supports were elucidated during the cracking reaction of n-dodecane under supercritical reaction conditions. The dynamical changes in nanocatalysts and catalytic activity are studied under realistic reaction conditions by using a combination of simultaneous temperature-programmed heating, in situ Small Angle X-ray Scattering (SAXS) and X-ray Absorption Near Edge Structure (XANES). In situ SAXS results indicate that the stability of the catalysts increases with Sn concentration. In situ XANES analysis reveals that the degree of oxidation and the electronic states of catalysts are dependent on the amount of Sn. Carbonaceous deposits over spent catalysts were characterized by Raman spectroscopy, indicating that the highest Sn loading inhibits the formation of disordered graphitic lattices, which leads to an increased catalytic activity. SiO2, γ-Al2O3 and Mg(Al)Ox were employed as supports to investigate the support effect on the stability of Pt catalysts. In situ SAXS and XANES results clearly show the improved stability of catalysts on γ-Al2O3 and Mg(Al)Ox supports compared to Pt catalysts on SiO2 and the electronic states of catalysts are strongly influenced by support materials.