YWYaling Wang

Yaling Wang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yaling Wang has a total of 16 co-authors. Here are the top co-authors by number of shared publications:

  • Liying Yang

    Tianjin University of Technology, Tianjin, China

    2 shared publications
  • Baiyue Wang

    Tianjin Key Laboratory of Organic Solar Cells and Photochemical Conversion, Department of Applied Chemistry, Tianjin University of Technology, Tianjin, China

    1 shared publication
  • Haina Zhu

    Tianjin Sino-German University of Applied Sciences, Tianjin, China

    1 shared publication
  • Hong Ge

    Tianjin Sino-German University of Applied Sciences, Tianjin, China

    1 shared publication
  • Jinzhao Li

    Key Laboratory of Display Materials and Photoelectric Devices, Ministry of Education, the Tianjin Key Laboratory of Photoelectric Materials and Devices, and the School of Materials Science and Engineering, Tianjin University of Technology, Tianjin, China

    1 shared publication
  • Mao Liang

    Tianjin Key Laboratory of Organic Solar Cells and Photochemical Conversion Institution Department of Applied Chemistry Tianjin University of Technology Tianjin P. R. China

    1 shared publication

Latest Publications

  • SnO 2 -Ti 3 C 2 Blends as Electron Transport Layer for Efficient and Easily Fabricated Planar Perovskite Solar Cells

    by Yaling Wang, Yi Ding, Liying Yang, Shougen Yin, Sheng Xu, Haina Zhu, Hong Ge

    In this work, the SnO 2 -Ti 3 C 2 hybrid electron transport layer (ETL) was prepared by incorporating two-dimensional Ti 3 C 2 -MXene into SnO 2 and appropriate ultraviolet (UV) ozone treatment. The synergistic effect of Ti 3 C 2 introduction and UV ozone treatment on the charge transport capacity of SnO 2 ETL, interface properties of ETL/perovskite, perovskite morphology, and device performance was systematically investigated. The results show that the introduction of Ti 3 C 2 does not affect the morphology and transmittance of SnO 2 ETL. The perovskite films based on SnO 2 -Ti 3 C 2 are not only dense, but also have smaller surface roughness, more uniform, and larger grain size, even penetrating the entire perovskite film. The surface oxidation of Ti 3 C 2 induced by UV-ozone treatment enhanced the charge transport capacity of ETL. The electron extraction and charge transfer at the interface between SnO 2 -Ti 3 C 2 ETL and perovskite are higher, and carrier recombination is effectively suppressed. Perovskite solar cells (PSCs) based on SnO 2 -Ti 3 C 2 ETL have larger charge recombination impedance and higher electron mobility, mainly due to enhanced ETL charge transport and optimization of interface properties. The short-circuit current ( J sc) and filling factor (FF) of PSCs are increased by 5% and 7% respectively, delivering a champion device with a relatively high FF of 79.38% and high power conversion efficiency of 19.52%, as well as good stability. Thus, this study provides a simple and effective method for the preparation of efficient and repeatable PSCs and paves the way for the industrialization of PSCs to a certain extent.


  • Unveiling the Role of Conjugate Bridge in Triphenylamine Hole-Transporting Materials for Inverted and Direct Perovskite Solar Cells

    by Qi Zeng, Yungen Wu, Baiyue Wang, Yaling Wang, Rui Wang, Jinzhao Li, Mao Liang, Liying Yang, Song Xue

    Deeply understanding of the performance discrepancy of hole-transporting materials (HTMs) in perovskite solar cells (PSCs) with different configuration (inverted or direct) is important for designing efficient HTMs. Herein, three organic HTMs TZ1, TZ2, and TZ3 have been employed to fabricate the inverted PSCs. Optoelectronic properties and photovoltaic performance of these HTMs are investigated. TZ3 featuring the 3,6-di(thiophen-2-yl)thieno[3,2-b]thiophene conjugate bridge shows a higher work function and enhanced capability of hole extraction, achieving a higher power conversion efficiency (PCE) of 16.33% in the inverted PSCs. Importantly, results reveal that the conjugate bridge has a relevant effect on the photovoltaic performance of cells with different device configuration. The PCE trend of TZ1, TZ2, and TZ3 in inverted PSCs is diametrically opposed to that of direct devices. We proposed that linear triphenylamine HTMs contain a fused bridge with high degree of conjugation are good choice for the direct PSCs. On the other hand, it is better to incorporate linear triphenylamine HTMs with deep highest occupied molecular orbital (HOMO) toward the inverted PSCs, because the photovoltage plays a crucial role in the efficiency of the inverted PSCs. This systematic study provides a new viewpoint to design HTMs toward PSCs with different device configuration.


  • Outer-rotor switched reluctance motor and its control system used in electric vehicles

    by Wang Yaling, Xu Yanliang, Wang Yufang, Zhang Yun

    An in-wheel outer-rotor switched reluctance motor (SRM) is developed which will be applied in dual-motor independent driven electric vehicles (EV). Firstly, the whole motor driven system including switched reluctance motor, the main circuit of power converter, detection circuit and the controller with DSP TMS320F2812 are designed. Then the electric differential system is analyzed and designed. At last, the coordinated control of two motor is realized by electronic differential system based on Ackerman-Jeantand model.