JLJi‐Zhao Liang

Ji‐Zhao Liang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ji‐Zhao Liang has a total of 40 co-authors. Here are the top co-authors by number of shared publications:

  • Chak Yin Tang

    Department of Industrial and Systems Engineering, The Hong Kong Polytechnic University, Hong Kong, China

    5 shared publications
  • Bo Zhu

    Research Division of Green Function Materials and Equipment, School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou, People’s Republic of China

    4 shared publications
  • Chi Pong Tsui

    Department of Industrial and Systems Engineering, Faculty of Engineering, The Hong Kong Polytechnic University, Hong Kong, China

    4 shared publications
  • Quan‐Quan Yang

    School of Mechanical and Automotive Engineering South China University of Technology Guangzhou China

    3 shared publications
  • Feng-Jiao Li

    South China University of Technology

    2 shared publications
  • Feng‐Jiao Li

    Research Division of Green Function Materials and Equipment, School of Mechanical and Automotive Engineering South China University of Technology Guangzhou 510640 People's Republic of China

    2 shared publications

Latest Publications

  • Tensile properties and fire residue morphology of flame-retarded-polypropylene composites

    by Ji-Zhao Liang

    The polypropylene (PP) composites filled with flame retardants (including aluminum hydroxide (Al(OH)3), magnesium hydroxide (Mg(OH)2), and zinc borate (ZB)) were prepared, and the composites were separately loaded with polyolefin elastomer (POE) and nanometer calcium carbonate (nano-CaCO3). The tensile properties and the fire residue morphology of the specimens after burning for these three groups of composites were measured. The results were shown that the tensile fracture strength and the Young’s modulus increased while the tensile yield strength and the tensile elongation at break ( δb) decreased with increasing flame-retardant volume fraction. At the same flame-retardant content, the δb values of the PP/Al(OH)3/Mg(OH)2/ZB/nano-CaCO3/POE composite were the highest in the three groups of composites. The fire residue in the pyrolysis zone of the specimens increased corresponding to the increased flame-retardant volume fraction and with loading the nano-CaCO3 and POE, especially at low-flame-retardant concentration. The reinforcing and the flame-retarded mechanisms of the composites were discussed.


  • End pressure effects of polypropylene composites reinforced with multi-walled carbon nanotubes in capillary flow

    by Ji-Zhao Liang

    The influence of the size and content of multi-walled carbon nanotubes (MWCNTs) on the end pressure effects of polypropylene (PP) composite melts during capillary extrusion flow was investigated, with the test temperature varying from 190°C to 230°C and apparent shear rate ranging from 50 s−1 to 3000 s−1. The results showed that the end pressure drop increased with increasing apparent shear rates, while decreased with increasing test temperature, and the sensitivity of the end pressure drop to apparent shear rate for the composites was higher than that for the unfilled PP. The end pressure drop increased with increasing weight fraction and the specific surface area of the MWCNTs. The end pressure drop increased almost linearly with increasing the aspect ratio of the MWCNTs. Moreover, the end pressure effect mechanisms of the composite melts during a capillary extrusion flow were discussed.


  • Melt spinning flow behaviour of high-density polyethylene blended with low-density polyethylene

    by Ji-Zhao Liang

    The melt spinning flow behaviour of a high-density polyethylene (HDPE) blended with a low-density polyethylene (LDPE) was studied using a melt spinning technique in temperature ranging from 160 to 200°C and die extrusion velocity varying from 9 to 36 mm s−1. The results showed that the melt apparent extension viscosity of the blends was higher than those of the LDPE and HDPE; the melt apparent extension viscosity decreased with increasing temperature; while the melt apparent extension viscosity increased with increasing extension strain rate when the extension strain rate was lower than 0.2 s−1, and then decreased; the melt apparent extension viscosity reached up to a maximum value when extension strain rate was about 0.2 s−1; the relationship between the melt apparent extension viscosity and the LDPE weight fraction did not follow the mixing rule.


  • Voltage–current characteristics of high-density polyethylene conductive composites

    by Ji-Zhao Liang

    The high-density polyethylene (HDPE) conductive composites filled separately with carbon fibers (CFs), ethylene-vinyl acetate copolymer (EVA), and three kinds of carbon blacks (CBs) (including different diameter, BET specific area, and DBP value) were prepared, to investigate the influence of the property, size, and content of the conductive fillers on the nonlinear voltage–current characteristics of the HDPE conductive composites. The results showed that the relationship between the electric current density and the electric field intensity of the three HDPE/CB composites including the HDPE/CF composites, the HDPE/CB/CF composites, and the HDPE/EVA/CB composites was nonlinear. The nonlinear conductivity index of the HDPE/CF composites was kept a low level comparing to the HDPE/CB composites, the HDPE/CB/CF composites, and the HDPE/EVA/CB composites. Moreover, the nonlinear conductive behavior mechanisms were discussed.


  • Melt Elongation Flow Behavior of Low-Density Polyethylene Composites Filled with Nanoscale Zinc Oxide

    by Ji Zhao Liang

    The melt elongation flow properties of low-density polyethylene/nanoscale zinc oxide (nano-ZnO) composites were studied using a Rheotens rheometer (Göttfert Werkstoff-Prüfmaschinen GmbH, Buchen, Germany). The die extrusion rate varied from 9 to 36 mm/s, the temperature ranged from 160°C to 200°C, and the nano-ZnO weight fraction range was from 0.2 to 4 weight percent (wt.%). The results showed that the melt elongation stress increased with the increasing elongation strain rate; the melt elongation viscosity decreased with the increasing temperature, and the temperature dependence obeyed the Arrhenius equation. The melt elongation viscosity of the composites with 0.4–0.8 wt.% nano-ZnO was lower in the whole composite system. Moreover, the melt elongation viscosity increased when the elongation strain rate was lower than 0.3 s−1 and then decreased with the increasing elongation strain rate; the melt elongation viscosity reached a maximum at an elongation strain rate around 0.3 s−1 and presented the stress hardening phenomenon.


  • Electrical conductivities of high‐density polyethylene composites reinforced with carbon fiber and nanometer carbon black

    by Ji‐Zhao Liang

    The effect of carbon fiber (CF) content on the electric conductive behavior of high‐density polyethylene composites filled with 10 wt% nanometer carbon black (CB) was investigated. It was found that the influence of the CF and CB on the resistivity was not the sum of these two fillers; the resistivity varied slightly and irregularly when the CF weight fraction was lower than 6 wt%, and then decreased quickly. The intensity of positive temperature coefficient (PTC) increased first and then decreased with increasing the CF weight fraction; when the CF weight fraction increased to 12 wt% from 8 wt%, the PTC intensity of the composite systems increased to 6.6 from 3.4; when the CF weight fraction increased to 15 wt% from 12 wt%, the PTC intensity of the composites decreased to 4.8 from 6.6. This could be attributed to the aggregation of the conductive filler in the matrix in this case. POLYM. COMPOS., 40:E1801–E1807, 2019. © 2018 Society of Plastics Engineers


  • Melt shear flow behavior of flame-retardant polypropylene composites filled with microencapsulated red phosphorus

    by Ji-Zhao Liang, Bo Zhu, Mao-Sen Pan, Jin-Qing Feng

    Melt shear flow behavior and melt shear viscosity are important characterization of processing properties for polymeric materials. The effects of microencapsulated red phosphorus (MRP) content and experimental conditions on the melt shear flow behavior of the polypropylene (PP) composites were investigated using a torque rheometer. It was found that the melt shear viscosity, the torque, and energy consumption at balance state of the composites increased nonlinearly with increasing MRP weight fraction while decreased slightly with increasing temperature, the maximum torque increased with increasing the roller speed, and the dependence of the melt shear viscosity and the energy consumption at balance state on temperature roughly obeyed the Arrhenius equation. These findings would provide useful data for processing these flame-retardant PP composites.


  • Reversible nonlinear electrical conductive behavior of high-density polyethylene composites

    by Ji-Zhao Liang

    The reversible nonlinear electrical conductive properties of high-density polyethylene composites filled separately with carbon black (CB), ethylene-vinyl acetate copolymer, and carbon fiber (CF) were measured using a four-electrode method. It was found that these composites presented significant reversible nonlinear electrical conductive behavior under these experimental conditions; the correlation between the current density and the electrical field intensity was linear in a bi-logarithmic coordinate system; both the crossover current density and the conductivity were approximately a linear function of the conductivity in a bi-logarithmic coordinate system; there was a synergic effect in the electrical conductivity percolation threshold between the CB and CF in the matrix, and the percolation threshold decreased with increasing the Brunauer–Emmett–Teller specific area of the CB.


  • Relationship between fractal dimensions of fracture surface and impact toughness of polycaprolactone/nano‐CaCO3 composites

    by Ji‐Zhao Liang

    The fractal dimensions of the specimen impact fracture surface of nanosized calcium carbonate reinforced polycaprolactone (PCL) composites were determined using a structure‐function method; and the correlation between V‐notched Izod impact strength measured at room temperature and fractal dimensions was studied. It was found that the fractal dimension range of the specimen fracture surface was from about 1.918 to 1.967, and all of the correlation coefficients were higher than 0.9. There was a strong relationship between the fracture surface fractal dimension and the impact strength. It indicated that the specimen fracture surface of the composites had obvious fractal character, the measured impact strength increased with increasing the fracture surface fractal dimension, and the correlation between them obeyed a three‐order polynomial equation. In addition, the toughening mechanisms of the PCL nanocomposites were discussed.


  • Flame‐retardant and mechanical properties of rigid polyurethane foam/MRP/mg(OH)2/GF/HGB composites

    by A. Li, D. D. Yang, H. N. Li, C. L. Jiang, J. Z. Liang

    Some rigid polyurethane foam (RPUF) composites modified with microencapsulated red phosphorus (MRP), magnesium hydrate (Mg(OH)2), glass fiber (GF), and hollow glass bead (HGB) were prepared. The influence of the MRP, Mg(OH)2, GF, and HGB on the flame‐retardant, combustion, and mechanical properties of the filled RPUF composites was investigated. The results showed that the flame‐retardant and the combustion properties of the composites were obviously improved, the limiting oxygen index, half burning time and the residual mass/original mass ratio increased with increasing MRP/Mg(OH)2 weight fraction, especially in case of MRP/Mg(OH)2 weight fraction of 8 wt %; the carbon monoxide (CO) concentration decreased with increasing MRP/Mg(OH)2 weight fraction, When the composites were loaded appreciate content of the HGB and the GF, the maximum torque and compressive strength of the composites were improved. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 46551.