Matthias Perez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Matthias Perez has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Sebastien Boisseau
Univ. Grenoble Alpes
11 shared publications - Jerome Willemin
Univ. Grenoble Alpes, F-38000 Grenoble, France
6 shared publications J L Reboud
Univ. Grenoble Alpes, F-38000 Grenoble, France
4 shared publicationsP Gasnier
Univ. Grenoble Alpes, F-38000 Grenoble, France
3 shared publicationsGhislain Despesse
Univ. Grenoble Alpes, F-38000 Grenoble, France
2 shared publicationsJean Luc Reboud
Univ. Grenoble Alpes, F-38000 Grenoble, France
2 shared publications
Latest Publications
- Open Access
- 15 September 2020
- Published by ASME International
Design and Optimization of Piezoelectric Actuators for Aeroacoustic Noises Control in a Turbofan
This paper reports on the design and optimization of different types of piezoelectric actuators for aeroacoustic control applications. This study was carried out within the context of the European project CleanSky 2/InnoSTAT. The aim of our work is to reduce the aeroacoustic noises that appear in an airplane turbofan by adding an area of piezoelectric actuators on the Outlet Guide Vanes (OGV). These piezoelectric structures will subsequently be controlled with an active approach and tested in the open-jet anechoic wind tunnel at LMFE. The noise source which has to be reduce/control comes from vortices located in the turbulent flow (which can for example be created by the fan module) interacting with the stator blades. The predominant frequencies and the pressure fluctuations levels related to these vortices rely on the airflow speed and are fixed between 1000Hz and 2000Hz in our case. To reach the target, we plan to manufacture an area of piezoelectric actuators on the intrados and the extrados of the stator blades in order to control the response of the blade to the turbulence of the airflow responsible for the aeroacoustic noise. Several adjacent blades will be equipped with this type of transducers. This study outline the design and the optimization of each piezoelectric cell in order to achieve good results in the frequency range previously defined as well as an acceptable mechanical strength of the blade. A most detailed study on the active shunt will be investigate later on.
- 15 September 2020
- Published by ASME International
Open AccessDesign and Optimization of Piezoelectric Actuators for Aeroacoustic Noises Control in a Turbofan
This paper reports on the design and optimization of different types of piezoelectric actuators for aeroacoustic control applications. This study was carried out within the context of the European project CleanSky 2/InnoSTAT. The aim of our work is to reduce the aeroacoustic noises that appear in an airplane turbofan by adding an area of piezoelectric actuators on the Outlet Guide Vanes (OGV). These piezoelectric structures will subsequently be controlled with an active approach and tested in the open-jet anechoic wind tunnel at LMFE. The noise source which has to be reduce/control comes from vortices located in the turbulent flow (which can for example be created by the fan module) interacting with the stator blades. The predominant frequencies and the pressure fluctuations levels related to these vortices rely on the airflow speed and are fixed between 1000Hz and 2000Hz in our case. To reach the target, we plan to manufacture an area of piezoelectric actuators on the intrados and the extrados of the stator blades in order to control the response of the blade to the turbulence of the airflow responsible for the aeroacoustic noise. Several adjacent blades will be equipped with this type of transducers. This study outline the design and the optimization of each piezoelectric cell in order to achieve good results in the frequency range previously defined as well as an acceptable mechanical strength of the blade. A most detailed study on the active shunt will be investigate later on.
- 1 June 2020
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 140
A two degree-of-freedom linear vibration energy harvester for tram applications
- 1 June 2020
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 140
A two degree-of-freedom linear vibration energy harvester for tram applications
- 12 December 2017
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 27 (1) , 014003
Aeroelastic flutter energy harvesters self-polarized by triboelectric effects
This paper presents the performances of several electrostatic flutter energy harvesters tested in a wind tunnel between 0 and 20 m s −1 . The main idea is to use the flutter capability of thin flexible films confined between lateral walls to induce simultaneously the capacitance variations and the electrostatic polarization required by the triboelectric/electrostatic conversion. This technology provides thin and flexible devices and solve the electret’s stability issue (Perez et al 2015 Smart Mater. Struct. , Perez et al 2015 New Circuits and Systems ). Our prototypes (2 ) have a quick startup (from 3 m s −1 ) and an electrical power-flux density from 0.35 μ W cm −2 @3 m s −1 (light breeze) to 35 μ W cm −2 @20 m s −1 (fresh gale). A Maximum Power Point circuit has been developed to efficiently use the power provided by the energy harvesters. The energy harvester combined with its power management circuit has finally been used to supply an 868 MHz wireless sensor node with temperature and acceleration measurements, validating the complete energy harvesting chain.
- 12 December 2017
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 27 (1) , 014003
Aeroelastic flutter energy harvesters self-polarized by triboelectric effects
This paper presents the performances of several electrostatic flutter energy harvesters tested in a wind tunnel between 0 and 20 m s −1 . The main idea is to use the flutter capability of thin flexible films confined between lateral walls to induce simultaneously the capacitance variations and the electrostatic polarization required by the triboelectric/electrostatic conversion. This technology provides thin and flexible devices and solve the electret’s stability issue (Perez et al 2015 Smart Mater. Struct. , Perez et al 2015 New Circuits and Systems ). Our prototypes (2 ) have a quick startup (from 3 m s −1 ) and an electrical power-flux density from 0.35 μ W cm −2 @3 m s −1 (light breeze) to 35 μ W cm −2 @20 m s −1 (fresh gale). A Maximum Power Point circuit has been developed to efficiently use the power provided by the energy harvesters. The energy harvester combined with its power management circuit has finally been used to supply an 868 MHz wireless sensor node with temperature and acceleration measurements, validating the complete energy harvesting chain.
- 7 February 2017
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 26 (3) , 035028
Human-motion energy harvester for autonomous body area sensors
This paper reports on a method to optimize an electromagnetic energy harvester converting the low-frequency body motion and aimed at powering wireless body area sensors. This method is based on recorded accelerations, and mechanical and transduction models that enable an efficient joint optimization of the structural parameters. An optimized prototype of 14.8 mmØ × 52 mm, weighting 20 g, has generated up to 4.95 mW in a resistive load when worn at the arm during a run, and 6.57 mW when hand-shaken. Among the inertial electromagnetic energy harvesters reported so far, this one exhibits one of the highest power densities (up to 730 μ W cm −3 ). The energy harvester was finally used to power a bluetooth low energy wireless sensor node with accelerations measurements at 25 Hz.
- 7 February 2017
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 26 (3) , 035028
Human-motion energy harvester for autonomous body area sensors
This paper reports on a method to optimize an electromagnetic energy harvester converting the low-frequency body motion and aimed at powering wireless body area sensors. This method is based on recorded accelerations, and mechanical and transduction models that enable an efficient joint optimization of the structural parameters. An optimized prototype of 14.8 mmØ × 52 mm, weighting 20 g, has generated up to 4.95 mW in a resistive load when worn at the arm during a run, and 6.57 mW when hand-shaken. Among the inertial electromagnetic energy harvesters reported so far, this one exhibits one of the highest power densities (up to 730 μ W cm −3 ). The energy harvester was finally used to power a bluetooth low energy wireless sensor node with accelerations measurements at 25 Hz.
- Open Access
- 1 November 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 773 (1) , 012019
Water flow energy harvesters for autonomous flowmeters
This paper reports on a water flow energy harvester exploiting a horizontal axis turbine with distributed magnets of alternate polarities at the rotor periphery and air coils outside the pipe. The energy harvester operates down to 1.2L/min with an inlet section of 20mm of diameter and up to 25.2mW are provided at 20L/min in a 2.4V NiMH battery through a BQ25504 power management circuit. The pressure loss induced by the insertion of the energy harvester in the hydraulic circuit and by the extraction of energy has been limited to 0.05bars at 30L/min, corresponding to a minor loss coefficient of KEH=3.94.
- 1 November 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 773 (1) , 012019
Open AccessWater flow energy harvesters for autonomous flowmeters
This paper reports on a water flow energy harvester exploiting a horizontal axis turbine with distributed magnets of alternate polarities at the rotor periphery and air coils outside the pipe. The energy harvester operates down to 1.2L/min with an inlet section of 20mm of diameter and up to 25.2mW are provided at 20L/min in a 2.4V NiMH battery through a BQ25504 power management circuit. The pressure loss induced by the insertion of the energy harvester in the hydraulic circuit and by the extraction of energy has been limited to 0.05bars at 30L/min, corresponding to a minor loss coefficient of KEH=3.94.
- Open Access
- 1 November 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 773 (1) , 012118
A triboelectric wind turbine for small-scale energy harvesting
This paper deals with a rotational energy harvester including a Horizontal Axis Wind Turbine (HAWT), a cylindrical stator covered by several electrodes, and thin Teflon dielectric membranes hung on the rotor. The sliding contact of the Teflon membranes on the stator provides simultaneously large capacitance variations and a polarization source for the electrostatic converter by exploiting triboelectric phenomena. 1µW has been harvested at 4m/s; 130µW at 10m/s and 550µW at 20m/s with a 40mmØ device. In order to validate the energy harvesting chain, the airflow energy harvester has been connected to a power management circuit implementing Synchronous Electric Charge Extraction (SECE) to supply a wireless sensor node with temperature and acceleration measurements, transmitted to a computer at 868MHz.
- 1 November 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 773 (1) , 012118
Open AccessA triboelectric wind turbine for small-scale energy harvesting
This paper deals with a rotational energy harvester including a Horizontal Axis Wind Turbine (HAWT), a cylindrical stator covered by several electrodes, and thin Teflon dielectric membranes hung on the rotor. The sliding contact of the Teflon membranes on the stator provides simultaneously large capacitance variations and a polarization source for the electrostatic converter by exploiting triboelectric phenomena. 1µW has been harvested at 4m/s; 130µW at 10m/s and 550µW at 20m/s with a 40mmØ device. In order to validate the energy harvesting chain, the airflow energy harvester has been connected to a power management circuit implementing Synchronous Electric Charge Extraction (SECE) to supply a wireless sensor node with temperature and acceleration measurements, transmitted to a computer at 868MHz.
- Open Access
- 1 November 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 773 (1) , 012021
Triboelectret-based aeroelastic flutter energy harvesters
This paper highlights some experimental results on several electrostatic membranes tested in a wind tunnel between 0 and 20m.s-1 for airflow energy harvesting. The main idea is to use the aeroelastic behavior of thin flexible films to induce simultaneously the capacitance variations and the polarization required by the triboelectric/electrostatic conversion. This technology provides thin and flexible devices and avoids the issue of electrets discharge. Our prototypes (2) allowed a quick startup (from 3ms-1), an electrical power-flux density from 0.1μW.cm-2 to 60μW.cm-2. In order to complete the energy harvesting chain, we have used a wireless sensor with temperature and acceleration measures coupled to a low power transmission (Bluetooth Low Energy) with reception on a smartphone.
- 1 November 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 773 (1) , 012021
Open AccessTriboelectret-based aeroelastic flutter energy harvesters
This paper highlights some experimental results on several electrostatic membranes tested in a wind tunnel between 0 and 20m.s-1 for airflow energy harvesting. The main idea is to use the aeroelastic behavior of thin flexible films to induce simultaneously the capacitance variations and the polarization required by the triboelectric/electrostatic conversion. This technology provides thin and flexible devices and avoids the issue of electrets discharge. Our prototypes (2) allowed a quick startup (from 3ms-1), an electrical power-flux density from 0.1μW.cm-2 to 60μW.cm-2. In order to complete the energy harvesting chain, we have used a wireless sensor with temperature and acceleration measures coupled to a low power transmission (Bluetooth Low Energy) with reception on a smartphone.
- Open Access
- 1 November 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 773 (1) , 012044
Scaling effects in a non-linear electromagnetic energy harvester for wearable sensors
In the field of inertial energy harvesters targeting human mechanical energy, the ergonomics of the solutions impose to find the best compromise between dimensions reduction and electrical performance. In this paper, we study the properties of a non-linear electromagnetic generator at different scales, by performing simulations based on an experimentally validated model and real human acceleration recordings. The results display that the output power of the structure is roughly proportional to its scaling factor raised to the power of five, which indicates that this system is more relevant at lengths over a few centimetres.
- 1 November 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 773 (1) , 012044
Open AccessScaling effects in a non-linear electromagnetic energy harvester for wearable sensors
In the field of inertial energy harvesters targeting human mechanical energy, the ergonomics of the solutions impose to find the best compromise between dimensions reduction and electrical performance. In this paper, we study the properties of a non-linear electromagnetic generator at different scales, by performing simulations based on an experimentally validated model and real human acceleration recordings. The results display that the output power of the structure is roughly proportional to its scaling factor raised to the power of five, which indicates that this system is more relevant at lengths over a few centimetres.
- 14 March 2016
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 25 (4) , 045015
A cm scale electret-based electrostatic wind turbine for low-speed energy harvesting applications
This paper presents a small-scale airflow energy harvester built on an axial turbine architecture and exploiting an electret-based electrostatic converter. When the airflow velocity is high enough, the windmill starts rotating and creates a periodic relative motion between a stator and a rotor which induces variations of capacitance. These ones are directly converted into electricity thanks to the use of Teflon electrets charged at −1400 V which polarize the variable capacitors. We focus our study on a 4-blade axial turbine with a diameter of D = 40 mm, a depth of W = 10 mm, for a total volume of 12.6 cm 3 . This windmill has been tested with various blade angles and different types of electrostatic converters and output powers up to 90 μ W at 1.5 m s −1 (7.5 μ W cm −3 ) and 1.8 mW at 10 m s −1 (111 μ W cm −3 ) have been obtained so far. The coefficient of power reaches C p = 5.8% and among the small-scale airflow energy harvesters previously reported, this one has the lowest cut-in speed (1.5 m s −1 ).
- 14 March 2016
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 25 (4) , 045015
A cm scale electret-based electrostatic wind turbine for low-speed energy harvesting applications
This paper presents a small-scale airflow energy harvester built on an axial turbine architecture and exploiting an electret-based electrostatic converter. When the airflow velocity is high enough, the windmill starts rotating and creates a periodic relative motion between a stator and a rotor which induces variations of capacitance. These ones are directly converted into electricity thanks to the use of Teflon electrets charged at −1400 V which polarize the variable capacitors. We focus our study on a 4-blade axial turbine with a diameter of D = 40 mm, a depth of W = 10 mm, for a total volume of 12.6 cm 3 . This windmill has been tested with various blade angles and different types of electrostatic converters and output powers up to 90 μ W at 1.5 m s −1 (7.5 μ W cm −3 ) and 1.8 mW at 10 m s −1 (111 μ W cm −3 ) have been obtained so far. The coefficient of power reaches C p = 5.8% and among the small-scale airflow energy harvesters previously reported, this one has the lowest cut-in speed (1.5 m s −1 ).
- Open Access
- 26 October 2015
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 646 (1) , 012009
Design and performance of a small-scale wind turbine exploiting an electret-based electrostatic conversion
Application of atmospheric solution precursor plasma spray to photocatalytic devices for small and medium
- 26 October 2015
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 646 (1) , 012009
Open AccessDesign and performance of a small-scale wind turbine exploiting an electret-based electrostatic conversion
Application of atmospheric solution precursor plasma spray to photocatalytic devices for small and medium