Maher Shaira
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Maher Shaira has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
J. Courbon
Université de Lyon, INSA-Lyon, MATEIS CNRS UMR 5510, 7 avenue J. Capelle, F-69621 Villeurbanne, France
2 shared publications- Nathalie Godin
Matériaux, ingénierie et science [Villeurbanne
2 shared publications - Philippe Guy
Laboratory of Vibration and Acoustics, INSA Lyon 2 , Lyon 69621
2 shared publications Joël Courbon
Université de Lyon, INSA-Lyon, MATEIS CNRS UMR , Villeurbanne Cedex, France
1 shared publicationL. Deville
1 shared publication- Loïc Vanel
Université Lyon 1, CNRS, ILM, UMR 2 5306, F-69100 Villeurbanne
1 shared publication
Latest Publications
- Open Access
- 24 January 2018
- Published by Wiley in Journal of Materials
- Vol. 2018, 1-6
Modification of Aluminium 6063 Microstructure by Adding Boron and Titanium to Improve the Thermal Conductivity
This study aimed to improve the thermal conductivity of the Aluminium 6063 for heat sinks applications used in Central Processing Unit (CPU) of computers. Several studies had used different additional elements for this goal. In this paper, we studied the influence of Titanium and Boron addition on the thermal conductivity of Aluminium 6063. Several casting alloys samples were prepared with different percentage of addition elements and then heat-treated by homogenization and aging treatments. The results showed an important modification in thermal conductivity value per rapport to the reference metal, depending on the element of addition and its percentage. The bigger evolution was by using Boron in small percentage. More than 13% of the improvement was realized in the thermal conductivity with the addition of only 0.05% of Boron.
- 24 January 2018
- Published by Wiley in Journal of Materials
- Vol. 2018, 1-6
Open AccessModification of Aluminium 6063 Microstructure by Adding Boron and Titanium to Improve the Thermal Conductivity
This study aimed to improve the thermal conductivity of the Aluminium 6063 for heat sinks applications used in Central Processing Unit (CPU) of computers. Several studies had used different additional elements for this goal. In this paper, we studied the influence of Titanium and Boron addition on the thermal conductivity of Aluminium 6063. Several casting alloys samples were prepared with different percentage of addition elements and then heat-treated by homogenization and aging treatments. The results showed an important modification in thermal conductivity value per rapport to the reference metal, depending on the element of addition and its percentage. The bigger evolution was by using Boron in small percentage. More than 13% of the improvement was realized in the thermal conductivity with the addition of only 0.05% of Boron.
- 30 April 2010
- Published by Taylor & Francis in Research in Nondestructive Evaluation
- Vol. 21 (2) , 112-126
Monitoring of Martensitic Transformation in Austenitic Stainless Steel 304 L by Eddy Currents
A nondestructive eddy current technique has been applied to cyclic-strain induced martensitic transformation (MT) monitoring in austenitic stainless steel 304 L. During plastic deformation, the austenite transforms locally in martensite. Transformed martensite distribution depends on the geometry of the specimen under test (rectangular section in this work): transformation occurs first in the corners, later close to the flat free surfaces, and finally in the bulk. The obtained value is then representative of a small volume of the sample. Local measurements with an eddy current probe proved to be sensitive to this kind of transformation and even quantitatively after calibration. This article proposes a procedure to calibrate the eddy current response in order to determine the fraction of martensite formed under the probe without the need of X-ray measurements.
- 30 April 2010
- Published by Taylor & Francis in Research in Nondestructive Evaluation
- Vol. 21 (2) , 112-126
Monitoring of Martensitic Transformation in Austenitic Stainless Steel 304 L by Eddy Currents
A nondestructive eddy current technique has been applied to cyclic-strain induced martensitic transformation (MT) monitoring in austenitic stainless steel 304 L. During plastic deformation, the austenite transforms locally in martensite. Transformed martensite distribution depends on the geometry of the specimen under test (rectangular section in this work): transformation occurs first in the corners, later close to the flat free surfaces, and finally in the bulk. The obtained value is then representative of a small volume of the sample. Local measurements with an eddy current probe proved to be sensitive to this kind of transformation and even quantitatively after calibration. This article proposes a procedure to calibrate the eddy current response in order to determine the fraction of martensite formed under the probe without the need of X-ray measurements.
- 1 September 2008
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 492 (1-2) , 392-399
Evaluation of the strain-induced martensitic transformation by acoustic emission monitoring in 304L austenitic stainless steel: Identification of the AE signature of the martensitic transformation and power-law statistics
- 1 September 2008
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 492 (1-2) , 392-399
Evaluation of the strain-induced martensitic transformation by acoustic emission monitoring in 304L austenitic stainless steel: Identification of the AE signature of the martensitic transformation and power-law statistics
- 1 January 2005
- Published by Society of Advanced Science in Journal of Advanced Science
- Vol. 17 (1/2) , 105-111
Pulsed eddy current evolution for flaw detection in ferromagnetic materials
- 1 January 2005
- Published by Society of Advanced Science in Journal of Advanced Science
- Vol. 17 (1/2) , 105-111
Pulsed eddy current evolution for flaw detection in ferromagnetic materials