Kiang Hwee Tan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kiang Hwee Tan has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Akshay Venkateshwaran
Department of Civil and Environmental Engineering National University of Singapore Singapore
5 shared publications A Venkateshwaran
Department of Civil and Environmental Engineering, National University of Singapore, Singapore
1 shared publicationBogdan Cotovanu
1 shared publication- Chan Ghee Koh
National Univ. of Singapore
1 shared publication - Dongqi Jiang
Nanjing University of Science and Technology
1 shared publication - Gilbert Sebastiano Gondokusumo
Department of Civil and Environmental Engineering National University of Singapore Singapore Singapore
1 shared publication
Latest Publications
- 12 August 2026
- Published by Elsevier in Structures
- Vol. 92
Steel fibre-reinforced concrete dowel connection for composite downstand beams
- 12 August 2026
- Published by Elsevier in Structures
- Vol. 92
Steel fibre-reinforced concrete dowel connection for composite downstand beams
- 31 August 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 447
Shear strength and ductility of novel steel fibre-reinforced concrete dowel connections for composite beams
- 31 August 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 447
Shear strength and ductility of novel steel fibre-reinforced concrete dowel connections for composite beams
- 1 September 2021
- Published by Elsevier in Cement and Concrete Composites
- Vol. 122
Correlations among notched beam tests, double punch tests and round panel tests for a high performance fibre concrete cast at site
- 1 September 2021
- Published by Elsevier in Cement and Concrete Composites
- Vol. 122
Correlations among notched beam tests, double punch tests and round panel tests for a high performance fibre concrete cast at site
- 1 March 2020
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Structures and Buildings
- Vol. 173 (3) , 161-174
Moment redistribution in continuous steel-fibre-reinforced concrete slabs
The phenomenon of moment redistribution in steel-fibre-reinforced concrete (SFRC) members has not been adequately studied. In this study, the phenomenon was investigated by conducting point-load tests on seven two-span, one-way continuous slabs without traditional reinforcement. Significant redistribution of moments from the elastic values was observed at the critical mid-span and interior support sections. An analytical approach to predict the moment–curvature response of SFRC is presented, with which the predicted variation of moments with increasing load compared to the observed trends with reasonable accuracy. Also, the analytical approach predicts the load-carrying capacity of the slabs within 8% of the average observed values, with a standard deviation of 8%. In addition, the load–deflection curves of the slabs were well predicted. The results are beneficial for the analysis and design of a SFRC slabs-on-pile system by considering moment redistribution due to slab continuity.
- 1 March 2020
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Structures and Buildings
- Vol. 173 (3) , 161-174
Moment redistribution in continuous steel-fibre-reinforced concrete slabs
The phenomenon of moment redistribution in steel-fibre-reinforced concrete (SFRC) members has not been adequately studied. In this study, the phenomenon was investigated by conducting point-load tests on seven two-span, one-way continuous slabs without traditional reinforcement. Significant redistribution of moments from the elastic values was observed at the critical mid-span and interior support sections. An analytical approach to predict the moment–curvature response of SFRC is presented, with which the predicted variation of moments with increasing load compared to the observed trends with reasonable accuracy. Also, the analytical approach predicts the load-carrying capacity of the slabs within 8% of the average observed values, with a standard deviation of 8%. In addition, the load–deflection curves of the slabs were well predicted. The results are beneficial for the analysis and design of a SFRC slabs-on-pile system by considering moment redistribution due to slab continuity.
- 1 November 2018
- Published by Elsevier in Cement and Concrete Composites
- Vol. 94, 238-247
The use of limestone to replace physical filler of quartz powder in UHPFRC
- 1 November 2018
- Published by Elsevier in Cement and Concrete Composites
- Vol. 94, 238-247
The use of limestone to replace physical filler of quartz powder in UHPFRC
- 5 June 2018
- Published by Wiley in Structural Concrete
- Vol. 20 (1) , 15-31
Structural performance evaluation of innovative prestressed concrete floating fuel storage tanks
Prestressed concrete (PC) tanks have been widely used in industrial applications and are commonly constructed as base‐supported structures. In land–space constrained cities, it may be viable to construct such facilities as floating structures on sea areas. Several innovative conceptual designs of floating fuel storage tanks, including double‐ and single‐hull structures, are first proposed in this paper. For this new type of fuel storage facility, the self‐weight and in‐fill fuel are balanced by buoyancy forces, and there is no need for massive foundations. Due to the absence of specific guidelines, many design concerns have to be addressed before a fully functional PC floating fuel storage facility can be designed and operated economically. In this study, finite‐element analyses are performed to investigate the structural behavior of floating fuel storage tanks of various design options. To mobilize the buoyancy and hydrostatic load effects during filling operations, water ballasting and the use of in‐fill expanded polystyrene foam were examined to optimize the performance of proposed concepts. Analysis results indicate that single‐hull tanks show better performance than double‐hull tanks because the hydrostatic pressure on the tank wall due to outside seawater and in‐fill fuel are balanced to a great extent. Following the principles of load‐balancing and allowable stress design approach, prestressing steel requirements are determined for the selected tank concept.
- 5 June 2018
- Published by Wiley in Structural Concrete
- Vol. 20 (1) , 15-31
Structural performance evaluation of innovative prestressed concrete floating fuel storage tanks
Prestressed concrete (PC) tanks have been widely used in industrial applications and are commonly constructed as base‐supported structures. In land–space constrained cities, it may be viable to construct such facilities as floating structures on sea areas. Several innovative conceptual designs of floating fuel storage tanks, including double‐ and single‐hull structures, are first proposed in this paper. For this new type of fuel storage facility, the self‐weight and in‐fill fuel are balanced by buoyancy forces, and there is no need for massive foundations. Due to the absence of specific guidelines, many design concerns have to be addressed before a fully functional PC floating fuel storage facility can be designed and operated economically. In this study, finite‐element analyses are performed to investigate the structural behavior of floating fuel storage tanks of various design options. To mobilize the buoyancy and hydrostatic load effects during filling operations, water ballasting and the use of in‐fill expanded polystyrene foam were examined to optimize the performance of proposed concepts. Analysis results indicate that single‐hull tanks show better performance than double‐hull tanks because the hydrostatic pressure on the tank wall due to outside seawater and in‐fill fuel are balanced to a great extent. Following the principles of load‐balancing and allowable stress design approach, prestressing steel requirements are determined for the selected tank concept.
- 21 November 2017
- Published by Wiley in Structural Concrete
- Vol. 19 (3) , 670-683
Load‐carrying capacity of steel fiber reinforced concrete beams at large deflections
Discrete steel fibers are known to control crack widening in concrete members thereby enabling them to carry loads up to large deflections. This study examined the flexural behavior of steel fiber reinforced concrete (SFRC) beams reinforced with steel fibers by conducting four‐point bending tests on eight beam specimens. The effect of reinforcing index (defined as the product of the volume fraction and the aspect ratio of steel fibers), fiber type, and beam depth was investigated. The load‐carrying capacity corresponding to different beam deflections was predicted using available constitutive stress–strain/crack width laws in tension. Although existing constitutive relations in tension predict the peak load capacity well, they fail to accurately predict the load‐carrying capacity at large deflections. Subsequently, a constitutive law is proposed using a back‐calculation technique which was validated with the results from four‐point bending tests conducted on 24 SFRC beams including 16 results found in the literature. The deviation of the predictions of the proposed model with regard to the average load‐carrying capacity at large deflections is within 12% from the observed values.
- 21 November 2017
- Published by Wiley in Structural Concrete
- Vol. 19 (3) , 670-683
Load‐carrying capacity of steel fiber reinforced concrete beams at large deflections
Discrete steel fibers are known to control crack widening in concrete members thereby enabling them to carry loads up to large deflections. This study examined the flexural behavior of steel fiber reinforced concrete (SFRC) beams reinforced with steel fibers by conducting four‐point bending tests on eight beam specimens. The effect of reinforcing index (defined as the product of the volume fraction and the aspect ratio of steel fibers), fiber type, and beam depth was investigated. The load‐carrying capacity corresponding to different beam deflections was predicted using available constitutive stress–strain/crack width laws in tension. Although existing constitutive relations in tension predict the peak load capacity well, they fail to accurately predict the load‐carrying capacity at large deflections. Subsequently, a constitutive law is proposed using a back‐calculation technique which was validated with the results from four‐point bending tests conducted on 24 SFRC beams including 16 results found in the literature. The deviation of the predictions of the proposed model with regard to the average load‐carrying capacity at large deflections is within 12% from the observed values.
- Open Access
- 1 September 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 246 (1) , 012025
Punching Shear in Steel Fibre Reinforced Concrete Slabs Without Traditional Reinforcement
The punching shear capacity of steel fibre reinforced concrete (SFRC) slabs without traditional steel bar reinforcement was investigated by conducting central point-load tests on twelve square slabs. The test parameters covered fibres with different multi-hook ends, concrete compressive strength, reinforcing index and slab thickness. The statistical performance of two existing models for the prediction of punching shear capacity of SFRC slabs without traditional reinforcement was examined. The load carrying capacity of these slabs were also assessed using the yield line theory. It is noted that the slabs failed primarily in flexure and the yield line theory predicted the load carrying capacities of the slabs most accurately. The reason for a flexural failure in SFRC slabs without steel bars is attributed to the lesser energy required in the propagation of an existing flexural cracks than in the creation of a new circumferential cracks around the column face.
- 1 September 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 246 (1) , 012025
Open AccessPunching Shear in Steel Fibre Reinforced Concrete Slabs Without Traditional Reinforcement
The punching shear capacity of steel fibre reinforced concrete (SFRC) slabs without traditional steel bar reinforcement was investigated by conducting central point-load tests on twelve square slabs. The test parameters covered fibres with different multi-hook ends, concrete compressive strength, reinforcing index and slab thickness. The statistical performance of two existing models for the prediction of punching shear capacity of SFRC slabs without traditional reinforcement was examined. The load carrying capacity of these slabs were also assessed using the yield line theory. It is noted that the slabs failed primarily in flexure and the yield line theory predicted the load carrying capacities of the slabs most accurately. The reason for a flexural failure in SFRC slabs without steel bars is attributed to the lesser energy required in the propagation of an existing flexural cracks than in the creation of a new circumferential cracks around the column face.
- 14 August 2017
- Published by Wiley in Structural Concrete
- Vol. 19 (2) , 352-365
Residual flexural strengths of steel fiber reinforced concrete with multiple hooked‐end fibers
This paper presents the results of 3‐point bending tests on 69 prenotched steel fiber reinforced concrete (SFRC) prisms conducted in accordance with EN 14651 to obtain the stress versus crack‐mouth‐opening displacement curves. SFRC prisms with fiber content greater than 20 kg/m3 and containing multiple hooked‐end fibers were found to exhibit deflection hardening behavior in bending after first crack. Based on the test results, empirical models to determine the residual flexural stresses are established through multiple regression analysis and further validated with test results available in the literature. The residual flexural strengths were found to be proportional to the reinforcing index, the square root of concrete compressive strength, and the square of the number of hooks at the fiber ends. Size effect is accounted for by introducing a factor which is a function of the fiber length. The empirical equations for the residual flexural strengths enable the use of Model Code 2010 constitutive relation for SFRC in tension without resorting to prism tests.
- 14 August 2017
- Published by Wiley in Structural Concrete
- Vol. 19 (2) , 352-365
Residual flexural strengths of steel fiber reinforced concrete with multiple hooked‐end fibers
This paper presents the results of 3‐point bending tests on 69 prenotched steel fiber reinforced concrete (SFRC) prisms conducted in accordance with EN 14651 to obtain the stress versus crack‐mouth‐opening displacement curves. SFRC prisms with fiber content greater than 20 kg/m3 and containing multiple hooked‐end fibers were found to exhibit deflection hardening behavior in bending after first crack. Based on the test results, empirical models to determine the residual flexural stresses are established through multiple regression analysis and further validated with test results available in the literature. The residual flexural strengths were found to be proportional to the reinforcing index, the square root of concrete compressive strength, and the square of the number of hooks at the fiber ends. Size effect is accounted for by introducing a factor which is a function of the fiber length. The empirical equations for the residual flexural strengths enable the use of Model Code 2010 constitutive relation for SFRC in tension without resorting to prism tests.
- Open Access
- 1 June 2011
- Published by Walter de Gruyter GmbH in Science and Engineering of Composite Materials
- Vol. 18 (1-2) , 99-107
Towards a sustainable concrete: “sandless” concrete
As a step towards ensuring the sustainability of concrete as a construction material, an investigation was carried out on the mechanical and durability properties of concrete made without natural sand, termed “sandless” concrete, and with cement partially replaced by fly ash. Four groups of concrete mixes, with water-cement ( w/c ) ratios of 0.40, 0.45, 0.50 and 0.55, respectively, were studied. For each w/c ratio, there were six mixes with 0, 10%, 20%, 30%, 40% and 50% of cement content replaced by fly ash by mass, and one normal concrete mix containing natural sand. The difference in mechanical properties between normal and “sandless” concrete was not significant. “Sandless” concrete mixes with cement replaced by fly ash by <30% showed comparable compressive, splitting tensile and flexural strengths as those without fly ash. However, the elastic modulus was reduced with the incorporation of fly ash. In addition, use of fly ash led to reduced drying shrinkage of “sandless” concrete, and significantly improved the resistance to chloride ion penetration. The resistance to sulfate attack, on the other hand, seemed to decrease with higher fly ash content. From the study, it appears that “sandless” concrete with cement replaced by fly ash up to 30% could be considered for structural applications.
- 1 June 2011
- Published by Walter de Gruyter GmbH in Science and Engineering of Composite Materials
- Vol. 18 (1-2) , 99-107
Open AccessTowards a sustainable concrete: “sandless” concrete
As a step towards ensuring the sustainability of concrete as a construction material, an investigation was carried out on the mechanical and durability properties of concrete made without natural sand, termed “sandless” concrete, and with cement partially replaced by fly ash. Four groups of concrete mixes, with water-cement ( w/c ) ratios of 0.40, 0.45, 0.50 and 0.55, respectively, were studied. For each w/c ratio, there were six mixes with 0, 10%, 20%, 30%, 40% and 50% of cement content replaced by fly ash by mass, and one normal concrete mix containing natural sand. The difference in mechanical properties between normal and “sandless” concrete was not significant. “Sandless” concrete mixes with cement replaced by fly ash by <30% showed comparable compressive, splitting tensile and flexural strengths as those without fly ash. However, the elastic modulus was reduced with the incorporation of fly ash. In addition, use of fly ash led to reduced drying shrinkage of “sandless” concrete, and significantly improved the resistance to chloride ion penetration. The resistance to sulfate attack, on the other hand, seemed to decrease with higher fly ash content. From the study, it appears that “sandless” concrete with cement replaced by fly ash up to 30% could be considered for structural applications.