Malin Brodin
Malin Brodin has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Gary Chinga-Carrasco
RISE PFI, Trondheim, Norway
3 shared publications - María Cristina Area
Programa de Celulosa y Papel (PROCYP), Instituto de Materiales de Misiones, Consejo Nacional de Investigaciones Científicas y Técnicas, Facultad de Ciencias Exactas, Químicas y Naturales, Universidad Nacional de Misiones, Félix de Azara 1552, Posadas 3300, Misiones, Argentina
2 shared publications - Annie Fabian Abel Chimphango
Department of Chemical Engineering, University of Stellenbosch, Stellenbosch, South Africa
1 shared publication Antal Boldizar
Chalmers University of Technology
1 shared publication- Bård Helge Hoff
Department of Chemistry, Norwegian University of Science and Technology (NTNU), Høgskoleringen 5, NO-7491 Trondheim, Norway
1 shared publication - Caterina Lesaint Rusu
Department of Materials Science and Engineering, NTNU, N-7491 Trondheim, Norway
1 shared publication
Latest Publications
- Open Access
The Potential of Functionalized Ceramic Particles in Coatings for Improved Scratch Resistance
The top layer of a typical high pressure floor laminate (HPL) consists of a melamine formaldehyde (MF) impregnated special wear layer (overlay) with alumina particles. This top layer plays a crucial role in determining the mechanical properties of the laminate. For HPLs, scratch resistance and scratch visibility are particularly important properties. This study aimed to improve the mechanical properties, particularly the scratch resistance, by adjusting the composition of the overlay. Laminates containing alumina particles were prepared and tested. These alumina particles were additionally functionalized with a silane coupling agent to ensure better adhesion between the particles and the resin. The functionalized particles led to enhanced scratch resistance of the laminates as well as improved dispersion of the particles within the resin. Micro scratch testing revealed that by using functionalized particles, the scratch surface damage was reduced and the recovery characteristics of the surface layer were improved. Higher scratch resistance and scratch hardness were thus obtained, along with a reduced scratch visibility.
Open AccessThe Potential of Functionalized Ceramic Particles in Coatings for Improved Scratch Resistance
The top layer of a typical high pressure floor laminate (HPL) consists of a melamine formaldehyde (MF) impregnated special wear layer (overlay) with alumina particles. This top layer plays a crucial role in determining the mechanical properties of the laminate. For HPLs, scratch resistance and scratch visibility are particularly important properties. This study aimed to improve the mechanical properties, particularly the scratch resistance, by adjusting the composition of the overlay. Laminates containing alumina particles were prepared and tested. These alumina particles were additionally functionalized with a silane coupling agent to ensure better adhesion between the particles and the resin. The functionalized particles led to enhanced scratch resistance of the laminates as well as improved dispersion of the particles within the resin. Micro scratch testing revealed that by using functionalized particles, the scratch surface damage was reduced and the recovery characteristics of the surface layer were improved. Higher scratch resistance and scratch hardness were thus obtained, along with a reduced scratch visibility.
- Open Access
- 12 February 2018
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 6 (3) , 4068-4075
Pulping and Pretreatment Affect the Characteristics of Bagasse Inks for Three-dimensional Printing
- 12 February 2018
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 6 (3) , 4068-4075
Open AccessPulping and Pretreatment Affect the Characteristics of Bagasse Inks for Three-dimensional Printing
- 1 October 2017
- Published by Elsevier in Bioresource Technology
- Vol. 241, 669-680
Single-step microwave-assisted hot water extraction of hemicelluloses from selected lignocellulosic materials – A biorefinery approach
- 1 October 2017
- Published by Elsevier in Bioresource Technology
- Vol. 241, 669-680
Single-step microwave-assisted hot water extraction of hemicelluloses from selected lignocellulosic materials – A biorefinery approach
- Top Cited Papers
- 1 September 2017
- Published by Elsevier in Journal of Cleaner Production
- Vol. 162, 646-664
Lignocellulosics as sustainable resources for production of bioplastics – A review
- 1 September 2017
- Published by Elsevier in Journal of Cleaner Production
- Vol. 162, 646-664
Top Cited PapersLignocellulosics as sustainable resources for production of bioplastics – A review
- Open Access
- 31 January 2013
- Published by BioResources in BioResources
- Vol. 8 (2) , 2209-2221
Thermal and Viscoelastic Properties of Cellulosic Gels with Different Ionic Liquids and Coagulation Agents
Thermal and viscoelastic properties of three-component gels consisting of microcrystalline cellulose, ionic liquid, and coagulation agent were studied. The amount and type of components was varied to obtain different gel properties. The absorption of coagulation agent (13 to 35 %wt of water or ethanol) was found to depend on the types of ionic liquid and cellulose. Surface hydrophobization of cellulose prior to preparation of the gel remarkably resulted in the gels containing the most coagulation agent (35%wt). Rheological studies indicated a linear viscoelastic behavior in storage modulus but not in loss modulus, which is a behavior that, according to our knowledge, has not been seen before for gels. Increasing the cellulose concentration from 1:20 to 1:10 increased the stiffness of the gels. The highest critical stress value (1050 Pa) was obtained for a gel containing 1-butyl-3-methylimidazolium chloride and water. Finally, it was confirmed by dynamic-mechanical experiments that the gels had a cross-linked structure.
- 31 January 2013
- Published by BioResources in BioResources
- Vol. 8 (2) , 2209-2221
Open AccessThermal and Viscoelastic Properties of Cellulosic Gels with Different Ionic Liquids and Coagulation Agents
Thermal and viscoelastic properties of three-component gels consisting of microcrystalline cellulose, ionic liquid, and coagulation agent were studied. The amount and type of components was varied to obtain different gel properties. The absorption of coagulation agent (13 to 35 %wt of water or ethanol) was found to depend on the types of ionic liquid and cellulose. Surface hydrophobization of cellulose prior to preparation of the gel remarkably resulted in the gels containing the most coagulation agent (35%wt). Rheological studies indicated a linear viscoelastic behavior in storage modulus but not in loss modulus, which is a behavior that, according to our knowledge, has not been seen before for gels. Increasing the cellulose concentration from 1:20 to 1:10 increased the stiffness of the gels. The highest critical stress value (1050 Pa) was obtained for a gel containing 1-butyl-3-methylimidazolium chloride and water. Finally, it was confirmed by dynamic-mechanical experiments that the gels had a cross-linked structure.