Petr Vondrouš
Research Subjects
Petr Vondrouš has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Ladislav Kolařík
Faculty of Mechanical Engineering, Department of Manufacturing Technology, Czech Technical University in Prague, Prague, Czech Republic
3 shared publications - Marie Kolaříková
Faculty of Mechanical Engineering, Department of Manufacturing Technology, Czech Technical University in Prague, Prague, Czech Republic
3 shared publications Tomáš Kramár
Czech Technical University in Prague Faculty of Mechanical Engineering
2 shared publications- David Busek
Department of Electrotechnology, Faculty of Electrical Engineering, Czech Technical University in Prague, 16627 Prague, Czech Republic
1 shared publication - Hans-Jürgen Rusch
KAPKON GmbH, Max-Planck-Straße 23, Bad Salzuflen, Germany, EU
1 shared publication Jan Tauer
Czech Technical University in Prague Faculty of Mechanical Engineering
1 shared publication
Latest Publications
- 10 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Diagnostics of a Future Blow Hole Issue Before Assembly
Incorrect production of PTHs (Plated Through Holes) lead to problems during PCBA (Printed Circuit Board Assembly), specifically during soldering and caused blow hole issues. A novel method for identification of incorrectly produced PTHs is suggested in this work. Samples with questionable quality of plated through holes were received for analysis and various micro-sections and optical observations were performed. As the issue is a statistical problem, a thorough diagnostic of a single cross-section – an approach used commonly nowadays is nearly worthless as the fault is often a single weak point located anywhere within a 3D area of a plated barrel or within a significant number of such barrels. A method based on the optical observation of analyzed samples immersed in a viscous liquid in a vacuum chamber was successfully implemented.
- 10 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Diagnostics of a Future Blow Hole Issue Before Assembly
Incorrect production of PTHs (Plated Through Holes) lead to problems during PCBA (Printed Circuit Board Assembly), specifically during soldering and caused blow hole issues. A novel method for identification of incorrectly produced PTHs is suggested in this work. Samples with questionable quality of plated through holes were received for analysis and various micro-sections and optical observations were performed. As the issue is a statistical problem, a thorough diagnostic of a single cross-section – an approach used commonly nowadays is nearly worthless as the fault is often a single weak point located anywhere within a 3D area of a plated barrel or within a significant number of such barrels. A method based on the optical observation of analyzed samples immersed in a viscous liquid in a vacuum chamber was successfully implemented.
- Open Access
- 1 July 2019
- Published by Czech Technical University in Prague - Central Library in Acta Polytechnica
- Vol. 59 (3) , 292-298
JOINIG OF MG ALLOY AZ31B BY SELECTED TECHNOLOGIES
This contribution presents metallurgical joining of Mg alloy AZ 31B by several technologies - Friction Stir Welding - FSW, Laser Beam Welding - LBW, soldering and their mutual comparison. The difficulty of joining Mg alloys is connected with the strong MgO layer, low ductility of the weld metal (WM), a presence of intermetallic phases connected with the hardness increase. To successfully join Mg alloys, a precise setting of welding parameters is needed. The welds are susceptible to low mechanical properties as all samples fractured at WM. From the tested methods, laser beam welding proved the best results, because laser welding is the fastest and weld strength reached the highest values, i.e. 87% of BM (base metal) strength.
- 1 July 2019
- Published by Czech Technical University in Prague - Central Library in Acta Polytechnica
- Vol. 59 (3) , 292-298
Open AccessJOINIG OF MG ALLOY AZ31B BY SELECTED TECHNOLOGIES
This contribution presents metallurgical joining of Mg alloy AZ 31B by several technologies - Friction Stir Welding - FSW, Laser Beam Welding - LBW, soldering and their mutual comparison. The difficulty of joining Mg alloys is connected with the strong MgO layer, low ductility of the weld metal (WM), a presence of intermetallic phases connected with the hardness increase. To successfully join Mg alloys, a precise setting of welding parameters is needed. The welds are susceptible to low mechanical properties as all samples fractured at WM. From the tested methods, laser beam welding proved the best results, because laser welding is the fastest and weld strength reached the highest values, i.e. 87% of BM (base metal) strength.
- Open Access
- 28 February 2019
- Published by Czech Technical University in Prague - Central Library in Acta Polytechnica
- Vol. 59 (1) , 42-50
WELDING OF NITINOL BY SELECTED TECHNOLOGIES
Nitinol is a perspective alloy that is difficult to weld because of its high sensitivity to heat, atmospheric gases and the NiTi phase instability. We evaluated several welding techniques with regard to their applicability to weld fine pseudoelastic NiTi wires. Namely, we tested the microplasma arc, laser, electron beam, resistance and capacitor discharge welding. In conclusion, the behaviour of the weld for any of the implemented welding techniques is similar; it leads to a loss of mechanical properties in the welded joint caused by a recrystallization and an increased amount of brittle intermetallic phases. Yet, under perfect shielding and with a minimum heat input, the welds could, as a whole, retain the majority of their properties, and, as such, have the desired properties close to the base metal.
- 28 February 2019
- Published by Czech Technical University in Prague - Central Library in Acta Polytechnica
- Vol. 59 (1) , 42-50
Open AccessWELDING OF NITINOL BY SELECTED TECHNOLOGIES
Nitinol is a perspective alloy that is difficult to weld because of its high sensitivity to heat, atmospheric gases and the NiTi phase instability. We evaluated several welding techniques with regard to their applicability to weld fine pseudoelastic NiTi wires. Namely, we tested the microplasma arc, laser, electron beam, resistance and capacitor discharge welding. In conclusion, the behaviour of the weld for any of the implemented welding techniques is similar; it leads to a loss of mechanical properties in the welded joint caused by a recrystallization and an increased amount of brittle intermetallic phases. Yet, under perfect shielding and with a minimum heat input, the welds could, as a whole, retain the majority of their properties, and, as such, have the desired properties close to the base metal.
- 1 January 2019
- Published by TANGER Ltd.
- Vol. 2019, 1547-1553
JOINING OF THIN SHEETS FROM Al ALLOY EN AW 6016 BY CAPACITY DISCHARGE WELDING
- 1 January 2019
- Published by TANGER Ltd.
- Vol. 2019, 1547-1553
JOINING OF THIN SHEETS FROM Al ALLOY EN AW 6016 BY CAPACITY DISCHARGE WELDING
- 10 September 2013
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 586, 178-181
Mechanical Properties of Interface of Heterogeneous Diffusion Welds of Titanium and Austenitic Steel
Titanium is material which is used in many areas of human activity. Therefore it is necessary to join it with other material. It is very difficult to welding Ti with other metals by conventional fusion welding methods. There exist special joining technologies of heterogeneous materials which is possible to use. This is usually a joining of materials in the solid state, as diffusion welding, friction welding or explosion welding. This contribution deals with diffusion welding of titanium alloy Ti6Al4V and stainless austenitic steel 1.4301. There are described mechanical properties (as is reduced modulus Er and indentation hardness HIT) and changes of chemical composition of join due to diffusion of elements.
- 10 September 2013
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 586, 178-181
Mechanical Properties of Interface of Heterogeneous Diffusion Welds of Titanium and Austenitic Steel
Titanium is material which is used in many areas of human activity. Therefore it is necessary to join it with other material. It is very difficult to welding Ti with other metals by conventional fusion welding methods. There exist special joining technologies of heterogeneous materials which is possible to use. This is usually a joining of materials in the solid state, as diffusion welding, friction welding or explosion welding. This contribution deals with diffusion welding of titanium alloy Ti6Al4V and stainless austenitic steel 1.4301. There are described mechanical properties (as is reduced modulus Er and indentation hardness HIT) and changes of chemical composition of join due to diffusion of elements.
- Open Access
- 1 June 2012
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 12 (1) , 30-33
Experimental Verification of FEM Simulation of GMAW Bead on Plate Welding
The research focuses on verification of FEM simulation of GMAW bead on plate welding with experimental results. In the program Visual Environment simple FEM simulation of GMAW bead on plate welding on Al alloy EN AW 7022 was created and these ...
- 1 June 2012
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 12 (1) , 30-33
Open AccessExperimental Verification of FEM Simulation of GMAW Bead on Plate Welding
The research focuses on verification of FEM simulation of GMAW bead on plate welding with experimental results. In the program Visual Environment simple FEM simulation of GMAW bead on plate welding on Al alloy EN AW 7022 was created and these ...
- Open Access
- 4 January 2012
- Published by Czech Technical University in Prague - Central Library in Acta Polytechnica
- Vol. 52 (4)
Advanced Functions of a Modern Power Source for GMAW Welding of Steel
This paper evaluates the use of a modern welding power source equipped with advanced arc control functions. At the Laboratory of Welding Technologies of CTU in Prague we have focused on GMAW welding of steel using Sigma Galaxy, a modern welding power source produced by Migatronic. Sigma Galaxy is equipped with functions called Intelligent Arc Control and Sequence Repeat. According to the manufacturer, controlling an arc by these functions should significantly stabilize the welding process, lower the heat input and the deformation, and improve the weld quality. To evaluate the benefits of these functions completely, single V butt welds were performed on S275J2 structural steel 10 mm in thickness (2 weld layers: root+capping layer) in PF and PG positions. Welding was monitored by the Welding Information System, and was compared with standard GMAW welding. The results have shown that these “intelligent” functions offer significant advantages for steel welding, especially in vertical and overhead positions, because they lower the heat input and improve the weld metal control.
- 4 January 2012
- Published by Czech Technical University in Prague - Central Library in Acta Polytechnica
- Vol. 52 (4)
Open AccessAdvanced Functions of a Modern Power Source for GMAW Welding of Steel
This paper evaluates the use of a modern welding power source equipped with advanced arc control functions. At the Laboratory of Welding Technologies of CTU in Prague we have focused on GMAW welding of steel using Sigma Galaxy, a modern welding power source produced by Migatronic. Sigma Galaxy is equipped with functions called Intelligent Arc Control and Sequence Repeat. According to the manufacturer, controlling an arc by these functions should significantly stabilize the welding process, lower the heat input and the deformation, and improve the weld quality. To evaluate the benefits of these functions completely, single V butt welds were performed on S275J2 structural steel 10 mm in thickness (2 weld layers: root+capping layer) in PF and PG positions. Welding was monitored by the Welding Information System, and was compared with standard GMAW welding. The results have shown that these “intelligent” functions offer significant advantages for steel welding, especially in vertical and overhead positions, because they lower the heat input and improve the weld metal control.
- 1 January 2010
- Published by Japan Welding Society in JOURNAL OF THE JAPAN WELDING SOCIETY
- Vol. 79 (4) , 299-303
Welding and Engineering in Czech Republic (former Czechslovakia) : Yesterday and Today
- 1 January 2010
- Published by Japan Welding Society in JOURNAL OF THE JAPAN WELDING SOCIETY
- Vol. 79 (4) , 299-303
Welding and Engineering in Czech Republic (former Czechslovakia) : Yesterday and Today