Stewart A. Rounds
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Stewart A. Rounds has a total of 79 co-authors. Here are the top co-authors by number of shared publications:
- Annett B. Sullivan11 shared publications
- Norman L. Buccola
US Geol Survey, Oregon Water Sci Ctr, 2130 SW 5th Ave, Portland, OR 97201 USA
7 shared publications - Cassandra D. Smith
U.S. Geological Survey, Oregon Water Science Center, Bend, USA
6 shared publications - Krista L. Jones
U.S. Geological Survey, Oregon Water Science Center, 2130 Southwest 5th Avenue, Portland, Oregon, 97201, USA
6 shared publications - Laurel E. Stratton Garvin
College of Earth, Ocean, and Atmospheric Sciences Oregon State University Corvallis OR USA
5 shared publications Annett B. Sullivan
4 shared publications
Latest Publications
- Open Access
- 1 January 2025
- Published byĀ US Geological Survey
Effects of beaver dams and ponds on hydrologic and hydraulic responses of storm flows in urban streams of the Tualatin River Basin, northwestern Oregon
American beaver (Castor canadensis) dams fundamentally alter stream hydraulics and hydrology by temporarily impounding water in stream channels. Water managers are interested in how this impoundment translates to changes in hydrograph dynamics, particularly regarding the magnitude and duration of high flows, the temporary storage of storm water, and the range and spatial distribution of water depths and velocities. High-resolution two-dimensional hydraulic models were developed to compare hydraulic responses to storm events in two 1-kilometer long, relatively small (less than 5-meter-wide channel), urban stream reaches in the Tualatin River Basin (northwestern Oregon) with and without beaver dams. Results from modeling unsteady storm events show that: (1) beaver dams generally attenuate (temporarily impound) more water during storm events than an undammed reach, (2) the timing and dynamics of this attenuation are complicated and thus do not always result in a reduction of peak flows, and (3) the influence of beaver dams on stream hydraulics diminishes as the magnitude of flow events increase. Local geomorphic conditions, specifically the presence of off-channel features, affect the extent to which dams alter hydrograph dynamics. Although the magnitudes of peak flows are not substantially affected by the beaver dams considered in this study, results show that beaver dams temporarily impound a considerable amount of water throughout the duration of storms, which slows water conveyance to downstream reaches. Steady-state streamflow simulations at several streamflow magnitudes were also used to assess how beaver dams affect stream depths, velocities, and inundated areas, which are important factors affecting aquatic habitats. Results show that beaver dams result in a more hydraulically diverse stream, with substantially more inundated area, lower velocities, and greater depths than corresponding undammed scenarios. However, these differences diminish as streamflows increase and the channels overflow their banks and become hydraulically connected to adjacent floodplains. Together, these results confirm that beaver dams can fundamentally change urban stream channel hydraulics, but the influence of these dams is bounded by local geomorphic controls and is diminished at large streamflows.
- 1 January 2025
- Published byĀ US Geological Survey
Open AccessEffects of beaver dams and ponds on hydrologic and hydraulic responses of storm flows in urban streams of the Tualatin River Basin, northwestern Oregon
American beaver (Castor canadensis) dams fundamentally alter stream hydraulics and hydrology by temporarily impounding water in stream channels. Water managers are interested in how this impoundment translates to changes in hydrograph dynamics, particularly regarding the magnitude and duration of high flows, the temporary storage of storm water, and the range and spatial distribution of water depths and velocities. High-resolution two-dimensional hydraulic models were developed to compare hydraulic responses to storm events in two 1-kilometer long, relatively small (less than 5-meter-wide channel), urban stream reaches in the Tualatin River Basin (northwestern Oregon) with and without beaver dams. Results from modeling unsteady storm events show that: (1) beaver dams generally attenuate (temporarily impound) more water during storm events than an undammed reach, (2) the timing and dynamics of this attenuation are complicated and thus do not always result in a reduction of peak flows, and (3) the influence of beaver dams on stream hydraulics diminishes as the magnitude of flow events increase. Local geomorphic conditions, specifically the presence of off-channel features, affect the extent to which dams alter hydrograph dynamics. Although the magnitudes of peak flows are not substantially affected by the beaver dams considered in this study, results show that beaver dams temporarily impound a considerable amount of water throughout the duration of storms, which slows water conveyance to downstream reaches. Steady-state streamflow simulations at several streamflow magnitudes were also used to assess how beaver dams affect stream depths, velocities, and inundated areas, which are important factors affecting aquatic habitats. Results show that beaver dams result in a more hydraulically diverse stream, with substantially more inundated area, lower velocities, and greater depths than corresponding undammed scenarios. However, these differences diminish as streamflows increase and the channels overflow their banks and become hydraulically connected to adjacent floodplains. Together, these results confirm that beaver dams can fundamentally change urban stream channel hydraulics, but the influence of these dams is bounded by local geomorphic controls and is diminished at large streamflows.
- Open Access
- 1 January 2025
- Published byĀ US Geological Survey
Stream network capacity to support beaver dams in the Tualatin River Basin, northwestern Oregon
Beaver dams can help streams connect to their floodplains. These floodplain connections can expand the range of available aquatic habitats and aid in the restoration of stream and floodplain function and processes. American beavers (Castor canadensis) occupy a wide variety of aquatic habitats; however, their ability to build dams, the agent of stream and floodplain change, is constrained in large part by three physical variablesālocal vegetation, topography, and hydrology.These three physical variables are combined in the Beaver Restoration Assessment Tool (BRAT), a geographic information system-based utility that uses a Fuzzy Inference System (FIS) to estimate the capacity of each reach within a stream network to support beaver dams. In this study, version 1.0 of BRAT was adapted and applied to the entire perennial stream network of Tualatin River Basin in northwestern Oregon. Beaver-dam locations in the Tualatin River Basin were compiled to (1) define the distribution of dams in the basin during 2013ā16 and (2) provide necessary data for calibrating and validating BRAT predictions. BRAT was calibrated to the current known distribution of dams, as compiled in the inventory. The input FIS equations of the original BRAT model were adjusted to account for local topographic conditions; specifically, the low gradient of many streams in the basin, although subsequent updates to BRAT may obviate the need for these changes.Results from this modified BRAT model reasonably simulated the dam inventory. Results show that beavers can currently build the greatest density of dams, defined as number of dams per kilometer of stream, in the higher-gradient forested streams of the basin, whereas they can build the fewest number of dams per kilometer in urban streams along the lower-gradient valley floor. Estimated dam density was generally 5-15 dams per kilometer (km) for forested streams and 2-4 dams/km for urban streams. Improving riparian vegetation along urban streams may allow beavers to build on average four additional dams per kilometer compared to current conditions. Results from this study may help inform local stream and stormwater management by (1) identifying stream reaches with the most potential to support beaver dams, (2) determining the likely factors limiting potential for dam building, and (3) identifying potential areas where dam building may affect human infrastructure.
- 1 January 2025
- Published byĀ US Geological Survey
Open AccessStream network capacity to support beaver dams in the Tualatin River Basin, northwestern Oregon
Beaver dams can help streams connect to their floodplains. These floodplain connections can expand the range of available aquatic habitats and aid in the restoration of stream and floodplain function and processes. American beavers (Castor canadensis) occupy a wide variety of aquatic habitats; however, their ability to build dams, the agent of stream and floodplain change, is constrained in large part by three physical variablesālocal vegetation, topography, and hydrology.These three physical variables are combined in the Beaver Restoration Assessment Tool (BRAT), a geographic information system-based utility that uses a Fuzzy Inference System (FIS) to estimate the capacity of each reach within a stream network to support beaver dams. In this study, version 1.0 of BRAT was adapted and applied to the entire perennial stream network of Tualatin River Basin in northwestern Oregon. Beaver-dam locations in the Tualatin River Basin were compiled to (1) define the distribution of dams in the basin during 2013ā16 and (2) provide necessary data for calibrating and validating BRAT predictions. BRAT was calibrated to the current known distribution of dams, as compiled in the inventory. The input FIS equations of the original BRAT model were adjusted to account for local topographic conditions; specifically, the low gradient of many streams in the basin, although subsequent updates to BRAT may obviate the need for these changes.Results from this modified BRAT model reasonably simulated the dam inventory. Results show that beavers can currently build the greatest density of dams, defined as number of dams per kilometer of stream, in the higher-gradient forested streams of the basin, whereas they can build the fewest number of dams per kilometer in urban streams along the lower-gradient valley floor. Estimated dam density was generally 5-15 dams per kilometer (km) for forested streams and 2-4 dams/km for urban streams. Improving riparian vegetation along urban streams may allow beavers to build on average four additional dams per kilometer compared to current conditions. Results from this study may help inform local stream and stormwater management by (1) identifying stream reaches with the most potential to support beaver dams, (2) determining the likely factors limiting potential for dam building, and (3) identifying potential areas where dam building may affect human infrastructure.
- Open Access
- 1 January 2025
- Published byĀ US Geological Survey
Effects of beaver dams and ponds on water quality in urban streams of the Tualatin River Basin, northwestern Oregon
American beavers (Castor canadensis) are native to the Pacific Northwest, and their populations have increased in many locations after being nearly removed by historical trapping. Beaver dams have well-documented effects on water quality in forested streams, but their effects on water quality in urban streams have not been well characterized. The study documented the water-quality effects of beaver dams and beaver activity in selected urban streams of the Tualatin River Basin in northwestern Oregon. Variations in water quality upstream, downstream, and within ponded areas behind beaver dams were quantified with continuous measurements of water temperature, specific conductance, dissolved oxygen, and pH from May 2016 to November 2017 in two intensively monitored reaches of urban streams (Fanno and Bronson Creeks). Five other urban stream reaches were monitored upstream and downstream from beaver ponds using water-temperature sensors to document water-temperature changes in additional beaver-affected reaches. Spatial water-quality variations within a beaver pond along Fanno Creek were characterized in more detail on four hot summer afternoons with numerous measurements of temperature and dissolved oxygen. Results from the study were used to document and derive insights from measured patterns in the water-quality data, such as the following:Shallow and unshaded ponds created by beaver dams (such as at Fanno Creek) capture more solar radiation than channelized and shaded stream reaches, resulting in substantially warmer water temperatures during summer.A large beaver pond along Fanno Creek had variable water depths and riparian shade, resulting in a wide range of water-temperature and dissolved-oxygen conditions. Some conditions measured during summer were stressful for sensitive aquatic species, with temperatures higher than 18 degrees Celsius (°C) and (or) dissolved-oxygen concentrations less than 2 milligrams per liter (mg/L).Although water flowing out of beaver-affected reaches was warmer than water entering the reaches, water tended to cool downstream when streams returned to a more-shaded, confined channel (such as at Fanno Creek) or received subsurface inputs and exchange (such as at Bronson Creek).The magnitude of water-temperature increases in beaver ponds depended on site characteristics, such as the surface area and depth of the ponds, the extent of riparian shade, and the potential for subsurface exchange. Beaver dams caused Fanno Creek to overflow its banks, resulting in a wide and shallow floodplain pond that had little riparian shade in most places. In contrast, Bronson Creek remained in its stream channel behind the beaver dams, was often deeper and more shaded, and had more subsurface water exchange than the Fanno Creek reach. Despite the longer reach length, these differences caused the Bronson Creek reach to warm less than the Fanno Creek reach.Beaver dams trapped sediment and organic matter, and ponding increased the time available for organic matter to decompose in the trapped sediments, thus consuming dissolved oxygen. The construction of a beaver dam in the monitored reach of Bronson Creek during the study caused an increase in oxygen demands and a rapid decrease in dissolved-oxygen concentrations.Dissolved-oxygen concentrations in monitored study reaches were affected by primary production (algal photosynthesis) and respiration, and hypoxic (low to zero dissolved oxygen) conditions were measured in the two intensively monitored reaches for multiple weeks during summer. Two single-station stream metabolism models were used to calculate net ecosystem production in the two intensively monitored urban stream reaches. Results indicated that the reaches were heterotrophic, with respiration demands consuming more oxygen than what was produced through photosynthesis.Beaver ponds at all sites had a measurable effect on water quality, causing wider ranges in temperature and dissolved-oxygen conditions than would have occurred without ponding. That wider range (both spatially and temporally) might support a variety of aquatic organisms, but also is likely to increase the frequency of water-quality standard violations in those beaver-affected reaches. Any water-quality effects or standard violations associated with beaver dams and ponds, however, may be localized or transitory along the stream network. Restored stream reaches can attract beavers. Considering the potential for beaver colonization when designing habitat restoration plans will require evaluation of the potential water-quality changes associated with beaver dams and ponds alongside other desired physical changes.
- 1 January 2025
- Published byĀ US Geological Survey
Open AccessEffects of beaver dams and ponds on water quality in urban streams of the Tualatin River Basin, northwestern Oregon
American beavers (Castor canadensis) are native to the Pacific Northwest, and their populations have increased in many locations after being nearly removed by historical trapping. Beaver dams have well-documented effects on water quality in forested streams, but their effects on water quality in urban streams have not been well characterized. The study documented the water-quality effects of beaver dams and beaver activity in selected urban streams of the Tualatin River Basin in northwestern Oregon. Variations in water quality upstream, downstream, and within ponded areas behind beaver dams were quantified with continuous measurements of water temperature, specific conductance, dissolved oxygen, and pH from May 2016 to November 2017 in two intensively monitored reaches of urban streams (Fanno and Bronson Creeks). Five other urban stream reaches were monitored upstream and downstream from beaver ponds using water-temperature sensors to document water-temperature changes in additional beaver-affected reaches. Spatial water-quality variations within a beaver pond along Fanno Creek were characterized in more detail on four hot summer afternoons with numerous measurements of temperature and dissolved oxygen. Results from the study were used to document and derive insights from measured patterns in the water-quality data, such as the following:Shallow and unshaded ponds created by beaver dams (such as at Fanno Creek) capture more solar radiation than channelized and shaded stream reaches, resulting in substantially warmer water temperatures during summer.A large beaver pond along Fanno Creek had variable water depths and riparian shade, resulting in a wide range of water-temperature and dissolved-oxygen conditions. Some conditions measured during summer were stressful for sensitive aquatic species, with temperatures higher than 18 degrees Celsius (°C) and (or) dissolved-oxygen concentrations less than 2 milligrams per liter (mg/L).Although water flowing out of beaver-affected reaches was warmer than water entering the reaches, water tended to cool downstream when streams returned to a more-shaded, confined channel (such as at Fanno Creek) or received subsurface inputs and exchange (such as at Bronson Creek).The magnitude of water-temperature increases in beaver ponds depended on site characteristics, such as the surface area and depth of the ponds, the extent of riparian shade, and the potential for subsurface exchange. Beaver dams caused Fanno Creek to overflow its banks, resulting in a wide and shallow floodplain pond that had little riparian shade in most places. In contrast, Bronson Creek remained in its stream channel behind the beaver dams, was often deeper and more shaded, and had more subsurface water exchange than the Fanno Creek reach. Despite the longer reach length, these differences caused the Bronson Creek reach to warm less than the Fanno Creek reach.Beaver dams trapped sediment and organic matter, and ponding increased the time available for organic matter to decompose in the trapped sediments, thus consuming dissolved oxygen. The construction of a beaver dam in the monitored reach of Bronson Creek during the study caused an increase in oxygen demands and a rapid decrease in dissolved-oxygen concentrations.Dissolved-oxygen concentrations in monitored study reaches were affected by primary production (algal photosynthesis) and respiration, and hypoxic (low to zero dissolved oxygen) conditions were measured in the two intensively monitored reaches for multiple weeks during summer. Two single-station stream metabolism models were used to calculate net ecosystem production in the two intensively monitored urban stream reaches. Results indicated that the reaches were heterotrophic, with respiration demands consuming more oxygen than what was produced through photosynthesis.Beaver ponds at all sites had a measurable effect on water quality, causing wider ranges in temperature and dissolved-oxygen conditions than would have occurred without ponding. That wider range (both spatially and temporally) might support a variety of aquatic organisms, but also is likely to increase the frequency of water-quality standard violations in those beaver-affected reaches. Any water-quality effects or standard violations associated with beaver dams and ponds, however, may be localized or transitory along the stream network. Restored stream reaches can attract beavers. Considering the potential for beaver colonization when designing habitat restoration plans will require evaluation of the potential water-quality changes associated with beaver dams and ponds alongside other desired physical changes.
- Open Access
- 1 January 2025
- Published byĀ US Geological Survey
Beaver dams and their effects on urban streams in the Tualatin River Basin, northwestern Oregon
In response to growing interest in beaver-assisted restoration in the Tualatin River Basin of northwestern Oregon, the U.S. Geological Survey (USGS), in partnership with Clean Water Services, collected data from 2016ā17 and completed a series of studies to: (1) inventory known locations of beaver dams and activity in the Tualatin River Basin, (2) estimate the number of beaver dams in the Tualatin River Basin as of 2017 and the potential number of beaver dams that could be supported with riparian vegetation improvements, and (3) assess the effects of beaver dams and ponds on storm hydrology, hydraulics, and floodplain inundation, suspended-sediment transport and deposition, and water quality along two urban stream reaches (Fanno Creek at Greenway Park and Bronson Creek between Kaiser and Saltzman Roads). This fact sheet summarizes the results of these studies and implications for beaver-assisted restoration in the Tualatin River Basin.
- 1 January 2025
- Published byĀ US Geological Survey
Open AccessBeaver dams and their effects on urban streams in the Tualatin River Basin, northwestern Oregon
In response to growing interest in beaver-assisted restoration in the Tualatin River Basin of northwestern Oregon, the U.S. Geological Survey (USGS), in partnership with Clean Water Services, collected data from 2016ā17 and completed a series of studies to: (1) inventory known locations of beaver dams and activity in the Tualatin River Basin, (2) estimate the number of beaver dams in the Tualatin River Basin as of 2017 and the potential number of beaver dams that could be supported with riparian vegetation improvements, and (3) assess the effects of beaver dams and ponds on storm hydrology, hydraulics, and floodplain inundation, suspended-sediment transport and deposition, and water quality along two urban stream reaches (Fanno Creek at Greenway Park and Bronson Creek between Kaiser and Saltzman Roads). This fact sheet summarizes the results of these studies and implications for beaver-assisted restoration in the Tualatin River Basin.
- Open Access
- 1 January 2023
- Published byĀ US Geological Survey
Updates to CE-QUAL-W2 models for select U.S. Army Corps of Engineers reservoirs in the Willamette Valley Project and an inter-reservoir reach of the Middle Fork Willamette River, northwestern Oregon
Mechanistic models capable of simulating hydrodynamics and water temperature in rivers and reservoirs are valuable tools for investigating thermal conditions and their relation to dam operations and streamflow in river basins where upstream water storage and management decisions have an important influence on river reaches with threatened fish populations. In particular, models allow managers to investigate how new, untried operations or hypothetical structures might influence streamflow and temperature conditions downstream. CE-QUAL-W2 is a two-dimensional (laterally averaged) hydrodynamic water-quality model that has previously been used to investigate the downstream effects of dam operations and other anthropogenic influences on stream temperature in the Willamette River Basin in northwestern Oregon, a region with two populations of fish species designated as threatened under the Endangered Species Act. By linking CE-QUAL-W2 river models to models of upstream, large Willamette Valley Project dams and reservoirs, these models can be used to investigate how dam operations at individual dams can influence streamflow and thermal conditions in downstream river reaches as an integrated system. Integrated model simulations that include the large dams and reservoirs linked to downstream river reaches can help managers develop a better understanding of tradeoffs associated with potential retrofits or operational changes across the multipurpose dams in the Willamette Valley Project, the effect of dam management on downstream tributaries and the Willamette River, and the resulting potential effect on threatened fish populations and habitat conditions.River models capable of simulating river corridors downstream from U.S. Army Corps of Engineers dams were previously updated and integrated to simulate conditions that occurred from March through October of 2011 (a cool and wet year), 2015 (a hot and dry year), and 2016 (a moderately hot and dry year) using CE-QUAL-W2 version 4.2. These river models encompass the following:Coast Fork Willamette and Middle Fork Willamette Rivers, the Row River, and Fall Creek downstream from Cottage Grove, Dexter, Dorena, and Fall Creek Dams, respectively;South Fork McKenzie River downstream from Cougar Dam;McKenzie River downstream from its confluence with the South Fork McKenzie River;South Santiam River downstream from Foster Dam;North Santiam River downstream from Big Cliff Dam; andWillamette River from its start at the confluence of the Middle Fork Willamette and Coast Fork Willamette Rivers to Willamette Falls (river mile 26.0; near West Linn, Oregon).This report documents model modifications, boundary condition data sources or estimation methods, and goodness-of-fit statistics for six CE-QUAL-W2 reservoir models and one river model upstream from the existing river models. These models simulate (1) Hills Creek Lake; (2) Lookout Point Lake and Dexter Reservoir on the Middle Fork Willamette River; (3) the Middle Fork Willamette River reach between Hills Creek Dam upstream and Lookout Point Lake downstream; (4) Cougar Reservoir on the South Fork McKenzie River; (5) Green Peter Lake on the Middle Santiam River and Foster Lake on the South Santiam River; and (6) Detroit Lake and (7) Big Cliff Reservoir on the North Santiam River. These CE-QUAL-W2 models were built by a variety of researchers to simulate a range of conditions in past years; this report documents their upgrade to U.S. Geological Survey (USGS) edition 7 of version 4.2 of CE-QUAL-W2 and updates each model to simulate conditions from January through December of 2011, 2015, and 2016. Also included in this report is an explanation of modifications to the CE-QUAL-W2 source code that constitute USGS edition 7 of CE-QUAL-W2 version 4.2. Each of the models described in this report can be run in isolation or linked to downstream models as a āsystem modelā to simulate conditions in tributaries and (or) in the Willamette Valley Project as a whole.As part of the model updates described in this report, some model parameters were adjusted to improve stability or decrease model error, and boundary conditions including meteorological, hydrologic, and temperature inputs were developed and updated for model years 2011, 2015, and 2016, as necessary. In some cases, the data sources used to drive previous model versions were no longer available, which required the development and checking of new data sources or estimation techniques. Goodness-of-fit statistics for outflow from the dams and in simulated river reaches generally show a good model fit, with the models simulating subdaily water temperatures at most comparable locations with a mean absolute error of generally less than 1 degree Celsius (°C) and a reasonably low bias. Model simulation of the thermal vertical profiles in each reservoir also produced an overall mean absolute error of generally less than 1 °C for all 3 years, with the exception of the Hills Creek Lake Model and the Cougar Reservoir Model in years when the reservoirs did not fill (2015 and 2016). Both of these models have known calibration issues and tend to be sensitive to the choice of certain structural parameters in the model. Overall, the calibration process was focused on obtaining model settings that led to realistic water temperature predictions in all 3 years (2011, 2015, and 2016) without over-calibrating specifically to any single year. A complete investigation of model error for these reservoir submodels was beyond the scope of this investigation but could be undertaken in the future if better model performance for these two reservoirs is desired.
- 1 January 2023
- Published byĀ US Geological Survey
Open AccessUpdates to CE-QUAL-W2 models for select U.S. Army Corps of Engineers reservoirs in the Willamette Valley Project and an inter-reservoir reach of the Middle Fork Willamette River, northwestern Oregon
Mechanistic models capable of simulating hydrodynamics and water temperature in rivers and reservoirs are valuable tools for investigating thermal conditions and their relation to dam operations and streamflow in river basins where upstream water storage and management decisions have an important influence on river reaches with threatened fish populations. In particular, models allow managers to investigate how new, untried operations or hypothetical structures might influence streamflow and temperature conditions downstream. CE-QUAL-W2 is a two-dimensional (laterally averaged) hydrodynamic water-quality model that has previously been used to investigate the downstream effects of dam operations and other anthropogenic influences on stream temperature in the Willamette River Basin in northwestern Oregon, a region with two populations of fish species designated as threatened under the Endangered Species Act. By linking CE-QUAL-W2 river models to models of upstream, large Willamette Valley Project dams and reservoirs, these models can be used to investigate how dam operations at individual dams can influence streamflow and thermal conditions in downstream river reaches as an integrated system. Integrated model simulations that include the large dams and reservoirs linked to downstream river reaches can help managers develop a better understanding of tradeoffs associated with potential retrofits or operational changes across the multipurpose dams in the Willamette Valley Project, the effect of dam management on downstream tributaries and the Willamette River, and the resulting potential effect on threatened fish populations and habitat conditions.River models capable of simulating river corridors downstream from U.S. Army Corps of Engineers dams were previously updated and integrated to simulate conditions that occurred from March through October of 2011 (a cool and wet year), 2015 (a hot and dry year), and 2016 (a moderately hot and dry year) using CE-QUAL-W2 version 4.2. These river models encompass the following:Coast Fork Willamette and Middle Fork Willamette Rivers, the Row River, and Fall Creek downstream from Cottage Grove, Dexter, Dorena, and Fall Creek Dams, respectively;South Fork McKenzie River downstream from Cougar Dam;McKenzie River downstream from its confluence with the South Fork McKenzie River;South Santiam River downstream from Foster Dam;North Santiam River downstream from Big Cliff Dam; andWillamette River from its start at the confluence of the Middle Fork Willamette and Coast Fork Willamette Rivers to Willamette Falls (river mile 26.0; near West Linn, Oregon).This report documents model modifications, boundary condition data sources or estimation methods, and goodness-of-fit statistics for six CE-QUAL-W2 reservoir models and one river model upstream from the existing river models. These models simulate (1) Hills Creek Lake; (2) Lookout Point Lake and Dexter Reservoir on the Middle Fork Willamette River; (3) the Middle Fork Willamette River reach between Hills Creek Dam upstream and Lookout Point Lake downstream; (4) Cougar Reservoir on the South Fork McKenzie River; (5) Green Peter Lake on the Middle Santiam River and Foster Lake on the South Santiam River; and (6) Detroit Lake and (7) Big Cliff Reservoir on the North Santiam River. These CE-QUAL-W2 models were built by a variety of researchers to simulate a range of conditions in past years; this report documents their upgrade to U.S. Geological Survey (USGS) edition 7 of version 4.2 of CE-QUAL-W2 and updates each model to simulate conditions from January through December of 2011, 2015, and 2016. Also included in this report is an explanation of modifications to the CE-QUAL-W2 source code that constitute USGS edition 7 of CE-QUAL-W2 version 4.2. Each of the models described in this report can be run in isolation or linked to downstream models as a āsystem modelā to simulate conditions in tributaries and (or) in the Willamette Valley Project as a whole.As part of the model updates described in this report, some model parameters were adjusted to improve stability or decrease model error, and boundary conditions including meteorological, hydrologic, and temperature inputs were developed and updated for model years 2011, 2015, and 2016, as necessary. In some cases, the data sources used to drive previous model versions were no longer available, which required the development and checking of new data sources or estimation techniques. Goodness-of-fit statistics for outflow from the dams and in simulated river reaches generally show a good model fit, with the models simulating subdaily water temperatures at most comparable locations with a mean absolute error of generally less than 1 degree Celsius (°C) and a reasonably low bias. Model simulation of the thermal vertical profiles in each reservoir also produced an overall mean absolute error of generally less than 1 °C for all 3 years, with the exception of the Hills Creek Lake Model and the Cougar Reservoir Model in years when the reservoirs did not fill (2015 and 2016). Both of these models have known calibration issues and tend to be sensitive to the choice of certain structural parameters in the model. Overall, the calibration process was focused on obtaining model settings that led to realistic water temperature predictions in all 3 years (2011, 2015, and 2016) without over-calibrating specifically to any single year. A complete investigation of model error for these reservoir submodels was beyond the scope of this investigation but could be undertaken in the future if better model performance for these two reservoirs is desired.
- Open Access
- 1 January 2023
- Published byĀ US Geological Survey
Field techniques for fluorescence measurements targeting dissolved organic matter, hydrocarbons, and wastewater in environmental waters: Principles and guidelines for instrument selection, operation and maintenance, quality assurance, and data reporting
The use of field deployable fluorescence sensors by the U.S. Geological Survey has become increasingly common for a wide variety of surface water and groundwater investigations. This report addresses field deployable fluorometers that measure the fluorescence response of various substances in water exposed to incident light generated by the sensor. An introduction to the basic principles of field measurements of fluorescence is provided, as well as technical background information on sensors that target dissolved organic matter, wastewater, and hydrocarbons, including sensor selection, operating principles, key features, and design elements. General deployment, operation and maintenance protocols, quality-assurance techniques, and suggestions for data reporting are presented to facilitate and standardize the collection and accurate communication of data collected by the U.S. Geological Survey across studies, sites, and sensor types. Sensor performance issues and common interferences are also described. An appendix is included to describe sensor calibration criteria and procedures, reporting units, and specific approaches to correct for interferences for fluorescence of dissolved organic matter sensors.
- 1 January 2023
- Published byĀ US Geological Survey
Open AccessField techniques for fluorescence measurements targeting dissolved organic matter, hydrocarbons, and wastewater in environmental waters: Principles and guidelines for instrument selection, operation and maintenance, quality assurance, and data reporting
The use of field deployable fluorescence sensors by the U.S. Geological Survey has become increasingly common for a wide variety of surface water and groundwater investigations. This report addresses field deployable fluorometers that measure the fluorescence response of various substances in water exposed to incident light generated by the sensor. An introduction to the basic principles of field measurements of fluorescence is provided, as well as technical background information on sensors that target dissolved organic matter, wastewater, and hydrocarbons, including sensor selection, operating principles, key features, and design elements. General deployment, operation and maintenance protocols, quality-assurance techniques, and suggestions for data reporting are presented to facilitate and standardize the collection and accurate communication of data collected by the U.S. Geological Survey across studies, sites, and sensor types. Sensor performance issues and common interferences are also described. An appendix is included to describe sensor calibration criteria and procedures, reporting units, and specific approaches to correct for interferences for fluorescence of dissolved organic matter sensors.
- Open Access
- 1 January 2022
- Published byĀ US Geological Survey
Field techniques for the determination of algal pigment fluorescence in environmental watersāPrinciples and guidelines for instrument and sensor selection, operation, quality assurance, and data reporting
The use of algal fluorometers by the U.S. Geological Survey (USGS) has become increasingly common. The basic principles of algal fluorescence, instrument calibration, interferences, data quantification, data interpretation, and quality control are given in Hambrook Berkman and Canova (2007). Much of the guidance given for instrument maintenance, data storage, and quality assurance in Wagner and others (2006) are also applicable to algal fluorometers, although they are not explicitly discussed. Algal fluorometers have advanced substantially since these guidance documents were published; so that while the basic principles remain unchanged, new guidance is needed. This techniques and methods report is intended to provide additional information on algal fluorescence-sensor calibration, maintenance, measurement, data storage, and quality assurance that meet stated objectives of USGS data-collection efforts. The operations described facilitate and standardize the collection and accurate communication of algal fluorescence data collected by the USGS across studies, sites, and instrument types. This report provides technical background information on algal fluorescence sensors; including specifications, operating principles, key features, and design elements. Maintenance and calibration protocols, quality-assurance techniques, and suggestions for data reporting are presented. Sensor performance issues, common interferences, and strategies for addressing them are also described.
- 1 January 2022
- Published byĀ US Geological Survey
Open AccessField techniques for the determination of algal pigment fluorescence in environmental watersāPrinciples and guidelines for instrument and sensor selection, operation, quality assurance, and data reporting
The use of algal fluorometers by the U.S. Geological Survey (USGS) has become increasingly common. The basic principles of algal fluorescence, instrument calibration, interferences, data quantification, data interpretation, and quality control are given in Hambrook Berkman and Canova (2007). Much of the guidance given for instrument maintenance, data storage, and quality assurance in Wagner and others (2006) are also applicable to algal fluorometers, although they are not explicitly discussed. Algal fluorometers have advanced substantially since these guidance documents were published; so that while the basic principles remain unchanged, new guidance is needed. This techniques and methods report is intended to provide additional information on algal fluorescence-sensor calibration, maintenance, measurement, data storage, and quality assurance that meet stated objectives of USGS data-collection efforts. The operations described facilitate and standardize the collection and accurate communication of algal fluorescence data collected by the USGS across studies, sites, and instrument types. This report provides technical background information on algal fluorescence sensors; including specifications, operating principles, key features, and design elements. Maintenance and calibration protocols, quality-assurance techniques, and suggestions for data reporting are presented. Sensor performance issues, common interferences, and strategies for addressing them are also described.
- 1 January 2022
- Published byĀ US Geological Survey
Updates to models of streamflow and water temperature for 2011, 2015, and 2016 in rivers of the Willamette River Basin, Oregon
Mechanistic river models capable of simulating hydrodynamics and stream temperature are valuable tools for investigating thermal conditions and their relation to streamflow in river basins where upstream water storage and management decisions have an important influence on river reaches with threatened fish populations. In the Willamette River Basin in northwestern Oregon, a two-dimensional, hydrodynamic water-quality model (CEāQUALāW2) has been used to investigate the downstream effects of dam operations and other anthropogenic influences on stream temperature. By simulating the managed releases of water and various temperatures from the large Willamette Valley Project dams upstream of the modeling domain, these models can be used to investigate riverine temperature conditions and their relation to streamflow to determine where and when conditions are most challenging for threatened fish populations and how dam operations and flow management can affect and optimize thermal conditions in the river.The original models were initially developed to simulate conditions in springāautumn of 2001 and 2002. This report documents (1) the upgrade of the river models to CEāQUALāW2 version 4.2 and (2) the update of those models to simulate conditions that occurred from March through October of 2011, 2015, and 2016. These years were selected to represent a range of climatic and hydrologic conditions in the Willamette River Basin, including a ācool, wetā year (2011), a āhot, dryā year (2015), and a ānormalā year (2016). Six submodels comprise the modeling system updated in this report; each submodel can be run independently or run with the others as a system. These models include the Coast Fork and Middle Fork Willamette River submodel, which includes the Coast Fork and Middle Fork Willamette Rivers, the Row River, and Fall Creek; the McKenzie River submodel, which includes the South Fork McKenzie River downstream of Cougar Dam and the McKenzie River from its confluence with the South Fork McKenzie River to its mouth; the South Santiam River submodel, which comprises the South Santiam River from Foster Dam to the Santiam River; the North Santiam and Santiam River submodel, which includes the Santiam River and the North Santiam River downstream of Big Cliff Dam; the Upper Willamette River submodel, which includes the Willamette River from Eugene to Salem; and the Middle Willamette River submodel, which includes the Willamette River from Salem to Willamette Falls near Oregon City.The models included in this report were originally developed, calibrated, and documented by other researchers. As part of the model updates described here, some model parameters were adjusted to improve stability and decrease runtime. Boundary conditions including meteorological, hydrologic, and thermal parameters were developed and updated for model years 2011, 2015, and 2016. In many cases, the data sources used to drive the 2001 and 2002 models were no longer available, which required the use of new data sources, the determination of a proxy record, or the development of appropriate estimation techniques. Goodness-of-fit statistics for the updated models show a good model fit, with the models simulating subdaily water temperatures at most comparable locations with a mean absolute error of generally less than 1 °C and often nearing 0.5 °C, depending on the individual submodel, and a reasonably low bias. The subdaily mean error for the South Santiam River submodel produced the highest bias of any of the submodels. Goodness-of-fit statistics indicate that the results may be biased cool (ranging from -0.43 °C in 2016 to -0.80 °C in 2011 for subdaily results), but the only water temperature data available for comparison on the South Santiam River is itself estimated, and those estimates are known to be too high in summer. Depending on future modeling needs, that submodel may warrant further refinement, along with additional data collection to properly define and minimize any model bias.
- 1 January 2022
- Published byĀ US Geological Survey
Updates to models of streamflow and water temperature for 2011, 2015, and 2016 in rivers of the Willamette River Basin, Oregon
Mechanistic river models capable of simulating hydrodynamics and stream temperature are valuable tools for investigating thermal conditions and their relation to streamflow in river basins where upstream water storage and management decisions have an important influence on river reaches with threatened fish populations. In the Willamette River Basin in northwestern Oregon, a two-dimensional, hydrodynamic water-quality model (CEāQUALāW2) has been used to investigate the downstream effects of dam operations and other anthropogenic influences on stream temperature. By simulating the managed releases of water and various temperatures from the large Willamette Valley Project dams upstream of the modeling domain, these models can be used to investigate riverine temperature conditions and their relation to streamflow to determine where and when conditions are most challenging for threatened fish populations and how dam operations and flow management can affect and optimize thermal conditions in the river.The original models were initially developed to simulate conditions in springāautumn of 2001 and 2002. This report documents (1) the upgrade of the river models to CEāQUALāW2 version 4.2 and (2) the update of those models to simulate conditions that occurred from March through October of 2011, 2015, and 2016. These years were selected to represent a range of climatic and hydrologic conditions in the Willamette River Basin, including a ācool, wetā year (2011), a āhot, dryā year (2015), and a ānormalā year (2016). Six submodels comprise the modeling system updated in this report; each submodel can be run independently or run with the others as a system. These models include the Coast Fork and Middle Fork Willamette River submodel, which includes the Coast Fork and Middle Fork Willamette Rivers, the Row River, and Fall Creek; the McKenzie River submodel, which includes the South Fork McKenzie River downstream of Cougar Dam and the McKenzie River from its confluence with the South Fork McKenzie River to its mouth; the South Santiam River submodel, which comprises the South Santiam River from Foster Dam to the Santiam River; the North Santiam and Santiam River submodel, which includes the Santiam River and the North Santiam River downstream of Big Cliff Dam; the Upper Willamette River submodel, which includes the Willamette River from Eugene to Salem; and the Middle Willamette River submodel, which includes the Willamette River from Salem to Willamette Falls near Oregon City.The models included in this report were originally developed, calibrated, and documented by other researchers. As part of the model updates described here, some model parameters were adjusted to improve stability and decrease runtime. Boundary conditions including meteorological, hydrologic, and thermal parameters were developed and updated for model years 2011, 2015, and 2016. In many cases, the data sources used to drive the 2001 and 2002 models were no longer available, which required the use of new data sources, the determination of a proxy record, or the development of appropriate estimation techniques. Goodness-of-fit statistics for the updated models show a good model fit, with the models simulating subdaily water temperatures at most comparable locations with a mean absolute error of generally less than 1 °C and often nearing 0.5 °C, depending on the individual submodel, and a reasonably low bias. The subdaily mean error for the South Santiam River submodel produced the highest bias of any of the submodels. Goodness-of-fit statistics indicate that the results may be biased cool (ranging from -0.43 °C in 2016 to -0.80 °C in 2011 for subdaily results), but the only water temperature data available for comparison on the South Santiam River is itself estimated, and those estimates are known to be too high in summer. Depending on future modeling needs, that submodel may warrant further refinement, along with additional data collection to properly define and minimize any model bias.
- 1 January 2022
- Published byĀ US Geological Survey
The thermal landscape of the Willamette RiverāPatterns and controls on stream temperature and implications for flow management and cold-water salmonids
Water temperature is a primary control on the health, diversity, abundance, and distribution of aquatic species, but thermal degradation resulting from anthropogenic influences on rivers is a challenge to threatened species worldwide. In the Willamette River Basin, northwestern Oregon, spring-run Chinook salmon (Oncorhynchus tshawytscha) and winter-run steelhead (O. mykiss) are formerly abundant cold-water-adapted species that are now protected under the Endangered Species Act. Among the challenges to the health of cold-water salmonids in the Willamette River Basin, disruptions in the seasonal patterns of stream temperature imposed by 13 large, multipurpose dams on tributaries to the Willamette River, as well as temperatures routinely in excess of regulatory limits in the Willamette River Basin, are contributing factors. To better understand controls on stream temperature, the sensitivity of stream temperature to flow augmentation as a management tool for suppressing high temperatures, and the implications for threatened salmonids, this study used a two-dimensional hydrodynamic and water-quality model (CE-QUAL-W2) to investigate spatial and temporal patterns of stream temperature in the Willamette River Basin. This study focused on the upper 160.4 river miles of the Willamette River from the confluence of the Middle Fork and Coast Fork Willamette Rivers (river mile 187.2) to Willamette Falls (river mile 26.8), three representative climate years (2011, a cool and wet year; 2015, an extremely hot and dry year; and 2016, a moderately hot and dry year), and a series of flow-augmentation scenarios. Model results show that the Willamette River upstream from Willamette Falls is divisible into four characteristic āthermal reachesā with similar thermal patterns, depending on tributary input, warming rate, and the timing of thermal response. In general, the Willamette River warms downstream during spring and summer, but patterns are complex, influenced by tributary inflows, and seasonally variable. Except in cool wet years (as illustrated by 2011), modeling suggests that adversely warm conditions for spring-run Chinook salmon are extensive from June or July through August. The thermal influence of flow augmentation from dam storage on four tributaries with U.S. Army Corps of Engineers dams varies spatially along the Willamette River, seasonally, and in magnitude, depending on a range of factors like distance from the Willamette River, the temperature of dam outflow, and the thermal template of tributary reaches controlling stream temperature adjustment to environmental heat fluxes. Modeling suggests that targeted flow management (via augmentation from dam storage) can reduce the extent and duration of thermally stressful conditions for Chinook salmon for short periods, but modeling suggests that flow augmentation is limited in its ability to fundamentally alter the āthermal landscapeā (the entire range of temperature variation in a river system over space and time) of the Willamette River. While this research provides general insights into the thermal landscape of the Willamette River and its sensitivity to flow management, additional investigation into the thermal landscape of tributaries downstream from U.S. Army Corps of Engineers dams, as well as the thermal management of reservoirs, storage availability, and dam outflows, would be necessary to target specific management actions for supporting specified rearing or migration conditions for spring-run Chinook salmon and other cold-water-adapted species in the Willamette River Basin.
- 1 January 2022
- Published byĀ US Geological Survey
The thermal landscape of the Willamette RiverāPatterns and controls on stream temperature and implications for flow management and cold-water salmonids
Water temperature is a primary control on the health, diversity, abundance, and distribution of aquatic species, but thermal degradation resulting from anthropogenic influences on rivers is a challenge to threatened species worldwide. In the Willamette River Basin, northwestern Oregon, spring-run Chinook salmon (Oncorhynchus tshawytscha) and winter-run steelhead (O. mykiss) are formerly abundant cold-water-adapted species that are now protected under the Endangered Species Act. Among the challenges to the health of cold-water salmonids in the Willamette River Basin, disruptions in the seasonal patterns of stream temperature imposed by 13 large, multipurpose dams on tributaries to the Willamette River, as well as temperatures routinely in excess of regulatory limits in the Willamette River Basin, are contributing factors. To better understand controls on stream temperature, the sensitivity of stream temperature to flow augmentation as a management tool for suppressing high temperatures, and the implications for threatened salmonids, this study used a two-dimensional hydrodynamic and water-quality model (CE-QUAL-W2) to investigate spatial and temporal patterns of stream temperature in the Willamette River Basin. This study focused on the upper 160.4 river miles of the Willamette River from the confluence of the Middle Fork and Coast Fork Willamette Rivers (river mile 187.2) to Willamette Falls (river mile 26.8), three representative climate years (2011, a cool and wet year; 2015, an extremely hot and dry year; and 2016, a moderately hot and dry year), and a series of flow-augmentation scenarios. Model results show that the Willamette River upstream from Willamette Falls is divisible into four characteristic āthermal reachesā with similar thermal patterns, depending on tributary input, warming rate, and the timing of thermal response. In general, the Willamette River warms downstream during spring and summer, but patterns are complex, influenced by tributary inflows, and seasonally variable. Except in cool wet years (as illustrated by 2011), modeling suggests that adversely warm conditions for spring-run Chinook salmon are extensive from June or July through August. The thermal influence of flow augmentation from dam storage on four tributaries with U.S. Army Corps of Engineers dams varies spatially along the Willamette River, seasonally, and in magnitude, depending on a range of factors like distance from the Willamette River, the temperature of dam outflow, and the thermal template of tributary reaches controlling stream temperature adjustment to environmental heat fluxes. Modeling suggests that targeted flow management (via augmentation from dam storage) can reduce the extent and duration of thermally stressful conditions for Chinook salmon for short periods, but modeling suggests that flow augmentation is limited in its ability to fundamentally alter the āthermal landscapeā (the entire range of temperature variation in a river system over space and time) of the Willamette River. While this research provides general insights into the thermal landscape of the Willamette River and its sensitivity to flow management, additional investigation into the thermal landscape of tributaries downstream from U.S. Army Corps of Engineers dams, as well as the thermal management of reservoirs, storage availability, and dam outflows, would be necessary to target specific management actions for supporting specified rearing or migration conditions for spring-run Chinook salmon and other cold-water-adapted species in the Willamette River Basin.
- 1 January 2022
- Published byĀ US Geological Survey
Tracking heat in the Willamette River system, Oregon
The Willamette River Basin in northwestern Oregon is home to several cold-water fish species whose habitat has been altered by the Willamette Valley Project, a system of 13 dams and reservoirs operated by the U.S. Army Corps of Engineers. Water-resource managers use a variety of flow- and temperature-management strategies to ameliorate the effects of upstream Willamette Valley Project dams on the habitat and viability of these anadromous and native fish. In this study, new capabilities were added to the CE-QUAL-W2 two-dimensional flow and water-quality model to inform those flow- and temperature-management strategies by tracking the quantities and ages of water and heat from individual upstream sources to downstream locations in the Willamette River system. Specifically, the fraction of water and heat attributable to upstream dam releases or other water inputs, and the fraction of heat sourced from environmental heat fluxes across the water and sediment surfaces, were tracked and quantified in the river at all locations and times simulated by the model. Applying the updated CE-QUAL-W2 models to the Willamette River system for the months of March through October in the years 2011 (cool and wet), 2015 (hot and dry), and 2016 (warm and somewhat dry) demonstrated that the influence of upstream dam releases on downstream water temperature diminished within a few days as water moved downstream. At sites that are roughly two or more days of travel from upstream dams (Albany and downstream), the JulyāAugust fraction of riverine heat content that could be tracked back to upstream dam releases typically diminished to less than 20 percent, despite the fact that roughly 50 percent of JulyāAugust streamflow could be attributed to upstream dam releases at the same sites. In contrast, the fraction of riverine heat content that could be attributed to environmental energy fluxes continued to increase with downstream distance, from about 59 to 67 percent at Albany during JulyāAugust to 62 to 73 percent at Keizer and 68 to 79 percent at Newberg.At locations sufficiently far downstream, upstream dam releases affect water temperature mainly through a decrease in travel time (less time for environmental heat fluxes to warm the river during summer) and an increase in thermal mass (more water to dilute and buffer incoming heat fluxes) rather than through the simple transport of heat content (water temperature) released from the dams. This concept was explored not only for the baseline conditions that occurred in MarchāOctober of 2011, 2015, and 2016, but also for a hypothetical high-flow release during August 2016 and an actual high-flow release during August 2017. In these high-flow releases, an extra 2,500 cubic feet per second (roughly) was released from Dexter Dam on the Middle Fork Willamette River, and downstream effects were measured (2017, actual) and simulated (2016, hypothetical). Results of the simulations were consistent with insights gained from the baseline conditions, such that temperature changes caused by flow augmentation were substantial in upstream reaches (measured cooling of about 1.5 °C near Harrisburg [43 miles downstream] and Albany [84 miles downstream] in 2017, and cooling of about 0.5 °C near Albany in 2016) and diminished farther downstream, but still measurable (more than a few tenths of a degree Celsius) even at Newberg, which is about 154 miles downstream. The direct downstream effects of dam releases on the river heat content attributable to those releases were increased by the hypothetical flow augmentation, with increases of 20 percent at Harrisburg and 12 percent at Keizer. Even with a decreased influence of environmental energy fluxes on river heat content, however, the fraction of heat content attributable to such fluxes was still more than 50 percent at and downstream of Albany and more than 70 percent at Newberg, where the river temperature was less affected by upstream dam-release temperatures and instead was affected primarily by a decreased travel time and increased thermal mass.
- 1 January 2022
- Published byĀ US Geological Survey
Tracking heat in the Willamette River system, Oregon
The Willamette River Basin in northwestern Oregon is home to several cold-water fish species whose habitat has been altered by the Willamette Valley Project, a system of 13 dams and reservoirs operated by the U.S. Army Corps of Engineers. Water-resource managers use a variety of flow- and temperature-management strategies to ameliorate the effects of upstream Willamette Valley Project dams on the habitat and viability of these anadromous and native fish. In this study, new capabilities were added to the CE-QUAL-W2 two-dimensional flow and water-quality model to inform those flow- and temperature-management strategies by tracking the quantities and ages of water and heat from individual upstream sources to downstream locations in the Willamette River system. Specifically, the fraction of water and heat attributable to upstream dam releases or other water inputs, and the fraction of heat sourced from environmental heat fluxes across the water and sediment surfaces, were tracked and quantified in the river at all locations and times simulated by the model. Applying the updated CE-QUAL-W2 models to the Willamette River system for the months of March through October in the years 2011 (cool and wet), 2015 (hot and dry), and 2016 (warm and somewhat dry) demonstrated that the influence of upstream dam releases on downstream water temperature diminished within a few days as water moved downstream. At sites that are roughly two or more days of travel from upstream dams (Albany and downstream), the JulyāAugust fraction of riverine heat content that could be tracked back to upstream dam releases typically diminished to less than 20 percent, despite the fact that roughly 50 percent of JulyāAugust streamflow could be attributed to upstream dam releases at the same sites. In contrast, the fraction of riverine heat content that could be attributed to environmental energy fluxes continued to increase with downstream distance, from about 59 to 67 percent at Albany during JulyāAugust to 62 to 73 percent at Keizer and 68 to 79 percent at Newberg.At locations sufficiently far downstream, upstream dam releases affect water temperature mainly through a decrease in travel time (less time for environmental heat fluxes to warm the river during summer) and an increase in thermal mass (more water to dilute and buffer incoming heat fluxes) rather than through the simple transport of heat content (water temperature) released from the dams. This concept was explored not only for the baseline conditions that occurred in MarchāOctober of 2011, 2015, and 2016, but also for a hypothetical high-flow release during August 2016 and an actual high-flow release during August 2017. In these high-flow releases, an extra 2,500 cubic feet per second (roughly) was released from Dexter Dam on the Middle Fork Willamette River, and downstream effects were measured (2017, actual) and simulated (2016, hypothetical). Results of the simulations were consistent with insights gained from the baseline conditions, such that temperature changes caused by flow augmentation were substantial in upstream reaches (measured cooling of about 1.5 °C near Harrisburg [43 miles downstream] and Albany [84 miles downstream] in 2017, and cooling of about 0.5 °C near Albany in 2016) and diminished farther downstream, but still measurable (more than a few tenths of a degree Celsius) even at Newberg, which is about 154 miles downstream. The direct downstream effects of dam releases on the river heat content attributable to those releases were increased by the hypothetical flow augmentation, with increases of 20 percent at Harrisburg and 12 percent at Keizer. Even with a decreased influence of environmental energy fluxes on river heat content, however, the fraction of heat content attributable to such fluxes was still more than 50 percent at and downstream of Albany and more than 70 percent at Newberg, where the river temperature was less affected by upstream dam-release temperatures and instead was affected primarily by a decreased travel time and increased thermal mass.