Ertugrul Altuntas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ertugrul Altuntas has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Deniz Aydemir
Forest Industrial Engineering, Faculty of Forestry Bartin University Bartin Turkey
5 shared publications - Gulyaz Al
Canakkale Vocational School of Technical Sciences Çanakkale Onsekiz Mart University Canakkale Turkey
3 shared publications - Ayşegül APAYDIN
KAHRAMANMARAŞ SÜTÇÜ İMAM ÜNİVERSİTESİ, FEN BİLİMLERİ ENSTİTÜSÜ
2 shared publications - Bekir Cihad Bal
Kahramanmaraş Sütcü Imam University
2 shared publications - Eyyüp Karaoğul
Harran Universitesi
2 shared publications - Mehmet Hakkı Alma
Kahramanmaraş Sütçü İmam Üniversitesi
2 shared publications
Latest Publications
- 8 October 2026
- Published by Wiley in Starch - Stärke
- Vol. 78 (10)
Accelerated Weathering Performance and Biodegradation of Polyhydroxybutyrate Modified With PHB‐g‐MA
This study examined the effects of accelerated weathering on the structural, viscoelastic, rheological properties and biodegradability behavior of polyhydroxybutyrate (PHB) biopolymers modified with PHB grafted maleic anhydride (PHB‐g‐MA) copolymers. For this purpose, the PHB was first grafted using the microwave (MW) and extruder (Ext) methods at MA loading ratios of 5% and 10% (wt). Then, the obtained PHB‐g‐MA was blended with neat PHB in the twin screw extruder, and test samples were obtained after the injection molding process. The weathered and unweathered samples were characterized with scanning electron microscopy (SEM), structural properties, including color, surface roughness, and Fourier transform infrared spectroscopy (FTIR), dynamic mechanical analysis (DMA) and rheological properties, and biodegradability behavior, including fungal resistance and biodegradation behavior. According to the results, SEM analysis exhibited that the surface deformation after the accelerated weathering test was lower in the blends with PHB‐g‐MA‐MW than in the samples with PHB‐g‐MA‐Ext. The sample surfaces of both PHB‐g‐MA types were flatter and smoother than those of neat PHB. It was observed that adding PHB‐g‐MA enhanced the color stability of the blends by 10%. DMA results showed that weathering increased E′ , E″ , and tan δ , indicating altered viscoelastic behavior. Rheological analysis confirmed a shift toward more viscosity‐dominated behavior, and the accelerated weathering has no important effect on rheological properties. The addition of PHB‐g‐MA increased the biological decomposition of PHB blends, and lower fungal growth occurred in neat PHB according to the samples with PHB‐g‐MA.
- 8 October 2026
- Published by Wiley in Starch - Stärke
- Vol. 78 (10)
Accelerated Weathering Performance and Biodegradation of Polyhydroxybutyrate Modified With PHB‐g‐MA
This study examined the effects of accelerated weathering on the structural, viscoelastic, rheological properties and biodegradability behavior of polyhydroxybutyrate (PHB) biopolymers modified with PHB grafted maleic anhydride (PHB‐g‐MA) copolymers. For this purpose, the PHB was first grafted using the microwave (MW) and extruder (Ext) methods at MA loading ratios of 5% and 10% (wt). Then, the obtained PHB‐g‐MA was blended with neat PHB in the twin screw extruder, and test samples were obtained after the injection molding process. The weathered and unweathered samples were characterized with scanning electron microscopy (SEM), structural properties, including color, surface roughness, and Fourier transform infrared spectroscopy (FTIR), dynamic mechanical analysis (DMA) and rheological properties, and biodegradability behavior, including fungal resistance and biodegradation behavior. According to the results, SEM analysis exhibited that the surface deformation after the accelerated weathering test was lower in the blends with PHB‐g‐MA‐MW than in the samples with PHB‐g‐MA‐Ext. The sample surfaces of both PHB‐g‐MA types were flatter and smoother than those of neat PHB. It was observed that adding PHB‐g‐MA enhanced the color stability of the blends by 10%. DMA results showed that weathering increased E′ , E″ , and tan δ , indicating altered viscoelastic behavior. Rheological analysis confirmed a shift toward more viscosity‐dominated behavior, and the accelerated weathering has no important effect on rheological properties. The addition of PHB‐g‐MA increased the biological decomposition of PHB blends, and lower fungal growth occurred in neat PHB according to the samples with PHB‐g‐MA.
- 30 April 2026
- Published by Bartin Orman Fakultesi Dergisi in Bartın Orman Fakültesi Dergisi
- Vol. 28 (1) , 68-78
Evaluation of Eucalyptus Root Wood in Activated Carbon Production with Two-Stage Production Method
In this study, lignocellulosic wastes were utilized in activated carbon production. The root wastes remaining on the soil surface after cutting of eucalyptus trees (Eucalyptus grandis) grown in Mersin Karabucak region were evaluated as lignocellulosic raw materials. For this purpose, the root wood of the eucalyptus tree (Eucalyptus grandis) was sized after grinding and 40 mesh wood flour was used. Activated carbon production was carried out in two stages. For this, the root wood flour was firstly carbonized in a closed autoclave at 200℃ and 225℃ for 24 hours in the hydrothermal stage by utilizing the subcritical point of water. Afterward, activated carbons were produced in the pyrolysis stage at 400℃, 500℃, 600℃ and 700℃ for 30 minutes in nitrogen environment. The yield calculations, scanning electron microscopy (SEM), Brunauer -Emmett - Teller (BET), and Brunauer -Emmett - Teller (BET) analyses of the activated carbon samples were performed. According to the results obtained, the surface area of the activated carbons produced at 700 ℃ using the two-step process was obtained as 267.08 m2/g. According to the SEM images obtained, it was understood that the activated carbons had a partially porous structure. Pyrolysis process at low temperatures ensured higher O/C and H/C ratios and more functional groups in the structure of activated carbon. However, as the temperature increased, the hydrogen and oxygen ratios in the structure of activated carbon decreased. As a result, it is understood that activated carbons with high surface area and oxidized functional groups can be produced by using two-stage hydrothermal and pyrolysis methods of eucalyptus root woods.
- 30 April 2026
- Published by Bartin Orman Fakultesi Dergisi in Bartın Orman Fakültesi Dergisi
- Vol. 28 (1) , 68-78
Evaluation of Eucalyptus Root Wood in Activated Carbon Production with Two-Stage Production Method
In this study, lignocellulosic wastes were utilized in activated carbon production. The root wastes remaining on the soil surface after cutting of eucalyptus trees (Eucalyptus grandis) grown in Mersin Karabucak region were evaluated as lignocellulosic raw materials. For this purpose, the root wood of the eucalyptus tree (Eucalyptus grandis) was sized after grinding and 40 mesh wood flour was used. Activated carbon production was carried out in two stages. For this, the root wood flour was firstly carbonized in a closed autoclave at 200℃ and 225℃ for 24 hours in the hydrothermal stage by utilizing the subcritical point of water. Afterward, activated carbons were produced in the pyrolysis stage at 400℃, 500℃, 600℃ and 700℃ for 30 minutes in nitrogen environment. The yield calculations, scanning electron microscopy (SEM), Brunauer -Emmett - Teller (BET), and Brunauer -Emmett - Teller (BET) analyses of the activated carbon samples were performed. According to the results obtained, the surface area of the activated carbons produced at 700 ℃ using the two-step process was obtained as 267.08 m2/g. According to the SEM images obtained, it was understood that the activated carbons had a partially porous structure. Pyrolysis process at low temperatures ensured higher O/C and H/C ratios and more functional groups in the structure of activated carbon. However, as the temperature increased, the hydrogen and oxygen ratios in the structure of activated carbon decreased. As a result, it is understood that activated carbons with high surface area and oxidized functional groups can be produced by using two-stage hydrothermal and pyrolysis methods of eucalyptus root woods.
- 19 November 2025
- Published by Springer Nature in Cellulose
- Vol. 32 (18) , 10649-10668
Microwave-assisted graft copolymerization effects on the material properties of polyhydroxybutyrate-cellulose nanocrystal nanocomposites
- 19 November 2025
- Published by Springer Nature in Cellulose
- Vol. 32 (18) , 10649-10668
Microwave-assisted graft copolymerization effects on the material properties of polyhydroxybutyrate-cellulose nanocrystal nanocomposites
- 29 December 2023
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 6 (2) , 233-244
Some selected properties of composite material produced from plastic furniture waste and wood flour
In this study, composite boards were produced using waste plastic furniture parts and wood flour. Wood flour was used at rates of 0%, 15%, 30% and 45% in the preparation of composite boards. Thus, 1 control and 3 composite groups were created. The boards are produced in dimensions of 3.5x175x175 mm (thickness, width, length). Density, flexural strength, flexural modulus, deformation at break, tensile strength, tensile modulus, elongation at break, hardness tests and thermal gravimetric analysis (TGA) and differential scanning calorimeter (DSC) analysis were performed on the produced composite boards. According to the obtained data, it was determined that as the percentage of wood flour in the composite groups increased compared to the control group, the values of flexural strength, deformation at break, tensile strength and elongation at break decreased whereas the values of density, hardness, flexural modulus and tensile modulus increased. According to the TGA and DSC analysis results, it was understood that the waste plastic furniture parts were composed of linear low density polyethylene (LLDPE) and polypropylene (PP) polymer materials, also the decomposition temperature of the composite materials partially increased with the increase in the percentage of wood flour.
- 29 December 2023
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 6 (2) , 233-244
Some selected properties of composite material produced from plastic furniture waste and wood flour
In this study, composite boards were produced using waste plastic furniture parts and wood flour. Wood flour was used at rates of 0%, 15%, 30% and 45% in the preparation of composite boards. Thus, 1 control and 3 composite groups were created. The boards are produced in dimensions of 3.5x175x175 mm (thickness, width, length). Density, flexural strength, flexural modulus, deformation at break, tensile strength, tensile modulus, elongation at break, hardness tests and thermal gravimetric analysis (TGA) and differential scanning calorimeter (DSC) analysis were performed on the produced composite boards. According to the obtained data, it was determined that as the percentage of wood flour in the composite groups increased compared to the control group, the values of flexural strength, deformation at break, tensile strength and elongation at break decreased whereas the values of density, hardness, flexural modulus and tensile modulus increased. According to the TGA and DSC analysis results, it was understood that the waste plastic furniture parts were composed of linear low density polyethylene (LLDPE) and polypropylene (PP) polymer materials, also the decomposition temperature of the composite materials partially increased with the increase in the percentage of wood flour.
- 3 September 2023
- Published by Kahramanmaras Sutcu Imam University Journal of Engineering Sciences in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 26 (3) , 653-662
HİDROTERMAL ÖN İŞLEMLİ OKALİPTÜS KÖK ODUNLARINDAN PROLİZ YÖNTEMİYLE AKTİF KARBON ÜRETİLMESİ
Bu çalışmada, aktif karbon elde etmek için hammadde olarak Tarsus-Karabucak bölgesinde yetiştirilen okaliptüs ağacının (Eucalyptus grandis) kök odunları kullanılmıştır. Aktif karbonlar hidrotermal ve piroliz yöntemleri kullanılarak iki aşamada üretilmiştir. Hidrotermal yöntemde suyun süper kritik özelliğinden yararlanılarak lignoselülozik malzeme 200℃ ve 225℃’de kapalı otoklav sisteminde 24 saat tutulmuş sonrasında H3PO4 (fosforik asit) ile 1:1 oranında karıştırılarak kimyasal aktivasyon işlemi gerçekleştirilmiştir. Proliz aşamasında 400℃, 500℃, 600℃ ve 700℃ sıcaklıklarında azot ortamında 30 dakika bekletilerek karbonizasyon işlemi gerçekleştirilmiştir. Elde edilen aktif karbon numunelerinin taramalı elektron mikroskobu (SEM), Brunauer-Emmett-Teller (BET), Fourier dönüşümlü infrared (FT-IR) ve elementel analizi teknikleri kullanılarak karakterize edilmiştir. Elde edilen sonuçlara göre H3PO4 ile kimyasal aktivasyon işlemi kullanılarak 400℃ ve 600℃ sıcaklıklarda üretilen aktif karbonların yüzey alanı 1074 m2/g ve 1069 m2/g olarak elde edilmiştir. Elde edilen SEM görüntülerinde aktif karbonların yüksek poroziteye sahip olduğu anlaşılmıştır. Elementel analiz sonuçları incelendiğinde sıcaklığın arttıkça oksitlenmiş fonksiyonel grupların azaldığı anlaşılmıştır. Sonuç olarak okaliptüs kök odunlarından hidrotermal ve piroliz yöntemleri ile yüksek gözenek ve yüksek yüzey alanlarına sahip aktif karbonlar üretildi.
- 3 September 2023
- Published by Kahramanmaras Sutcu Imam University Journal of Engineering Sciences in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 26 (3) , 653-662
HİDROTERMAL ÖN İŞLEMLİ OKALİPTÜS KÖK ODUNLARINDAN PROLİZ YÖNTEMİYLE AKTİF KARBON ÜRETİLMESİ
Bu çalışmada, aktif karbon elde etmek için hammadde olarak Tarsus-Karabucak bölgesinde yetiştirilen okaliptüs ağacının (Eucalyptus grandis) kök odunları kullanılmıştır. Aktif karbonlar hidrotermal ve piroliz yöntemleri kullanılarak iki aşamada üretilmiştir. Hidrotermal yöntemde suyun süper kritik özelliğinden yararlanılarak lignoselülozik malzeme 200℃ ve 225℃’de kapalı otoklav sisteminde 24 saat tutulmuş sonrasında H3PO4 (fosforik asit) ile 1:1 oranında karıştırılarak kimyasal aktivasyon işlemi gerçekleştirilmiştir. Proliz aşamasında 400℃, 500℃, 600℃ ve 700℃ sıcaklıklarında azot ortamında 30 dakika bekletilerek karbonizasyon işlemi gerçekleştirilmiştir. Elde edilen aktif karbon numunelerinin taramalı elektron mikroskobu (SEM), Brunauer-Emmett-Teller (BET), Fourier dönüşümlü infrared (FT-IR) ve elementel analizi teknikleri kullanılarak karakterize edilmiştir. Elde edilen sonuçlara göre H3PO4 ile kimyasal aktivasyon işlemi kullanılarak 400℃ ve 600℃ sıcaklıklarda üretilen aktif karbonların yüzey alanı 1074 m2/g ve 1069 m2/g olarak elde edilmiştir. Elde edilen SEM görüntülerinde aktif karbonların yüksek poroziteye sahip olduğu anlaşılmıştır. Elementel analiz sonuçları incelendiğinde sıcaklığın arttıkça oksitlenmiş fonksiyonel grupların azaldığı anlaşılmıştır. Sonuç olarak okaliptüs kök odunlarından hidrotermal ve piroliz yöntemleri ile yüksek gözenek ve yüksek yüzey alanlarına sahip aktif karbonlar üretildi.
- Open Access
- 26 December 2022
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 5 (2) , 142-154
Odun-plastik kompozit malzemelerde genleştirilmiş perlit kullanımının araştırılması
Bu çalışmada, genleştirilmiş perlitin odun-plastik kompozitlerde kullanılmasının bazı mekanik, termal ve morfolojik özellikler üzerine etkisi araştırılmıştır. Kompozitlerin üretilmesi için polipropilen (PP), genleştirilmiş perlit, karaçam testere talaşı, mısır koçanı talaşı ve MAPP bağlayıcının bulunduğu reçeteler kullanılmıştır. Hazırlanan karışımlar ikiz vidalı ekstruder kullanılarak kompozit malzemeler üretilmiştir. Kompozitler içerisinde lignoselülozik maddelerin miktarı sabit tutularak genleştirilmiş perlitin miktarı tedrici olarak artırılarak etkisi araştırılmıştır. Üretilen kompozit levhalardan hazırlanan test örneklerinin mekanik (eğilme, çekme ve şok direnci, yüzey sertliği) özelliklerinin yanı sıra termal (TGA ve DSC) ve SEM analizleri yapılarak özellikleri araştırılmıştır. Analiz sonuçlarına göre genel olarak kompozit malzeme içerisindeki genleştirilmiş perlit oranı arttıkça eğilme direnci, çekme direnci, elastikiyet modülü, şok direnci ve sertlik değerlerinin arttığı belirlenmiştir. Ayrıca plastik malzeme ile lignoselülozik ve genleştirilmiş perlit arasında bağ yapması için eklenen MAPP maddesi, kompozitlerin mekanik özelliklerini iyileştirdiği anlaşılmıştır. Sonuç olarak, kompozitlere eklenen genleştirilmiş perlitin odun plastik kompozit malzemenin özelliklerini iyileştirdiği anlaşılmıştır.
- 26 December 2022
- Published by Mobilya ve Ahsap Malzeme Arastirmalari Dergisi in Mobilya ve Ahşap Malzeme Araştırmaları Dergisi
- Vol. 5 (2) , 142-154
Open AccessOdun-plastik kompozit malzemelerde genleştirilmiş perlit kullanımının araştırılması
Bu çalışmada, genleştirilmiş perlitin odun-plastik kompozitlerde kullanılmasının bazı mekanik, termal ve morfolojik özellikler üzerine etkisi araştırılmıştır. Kompozitlerin üretilmesi için polipropilen (PP), genleştirilmiş perlit, karaçam testere talaşı, mısır koçanı talaşı ve MAPP bağlayıcının bulunduğu reçeteler kullanılmıştır. Hazırlanan karışımlar ikiz vidalı ekstruder kullanılarak kompozit malzemeler üretilmiştir. Kompozitler içerisinde lignoselülozik maddelerin miktarı sabit tutularak genleştirilmiş perlitin miktarı tedrici olarak artırılarak etkisi araştırılmıştır. Üretilen kompozit levhalardan hazırlanan test örneklerinin mekanik (eğilme, çekme ve şok direnci, yüzey sertliği) özelliklerinin yanı sıra termal (TGA ve DSC) ve SEM analizleri yapılarak özellikleri araştırılmıştır. Analiz sonuçlarına göre genel olarak kompozit malzeme içerisindeki genleştirilmiş perlit oranı arttıkça eğilme direnci, çekme direnci, elastikiyet modülü, şok direnci ve sertlik değerlerinin arttığı belirlenmiştir. Ayrıca plastik malzeme ile lignoselülozik ve genleştirilmiş perlit arasında bağ yapması için eklenen MAPP maddesi, kompozitlerin mekanik özelliklerini iyileştirdiği anlaşılmıştır. Sonuç olarak, kompozitlere eklenen genleştirilmiş perlitin odun plastik kompozit malzemenin özelliklerini iyileştirdiği anlaşılmıştır.
- 9 July 2019
- Published by SAGE Publications in Plastics, Rubber and Composites: Macromolecular Engineering
- Vol. 48 (9) , 389-400
Mechanical, thermal and morphological properties of heat-treated wood-polypropylene composites and comparison of the composites with PROMETHEE method
The aim of the paper was to determine the mechanical, thermal, and morphological properties of heat-treated wood-polypropylene polymer composites (WPCs) and to select the composites having the optimum properties with the PROMETHEE method. In this study, polypropylene (PP) as a matrix, wood thermally treated at 180°C and 220°C as reinforcement filler were examined for preparing composites. The PP composites were compounded using a twin-screw extruder and test specimens were prepared by compression moulding. According to the test results, the thermal and mechanical properties of the WPCs generally increased with the addition of heat-treated wood fillers. The SEM images showed that the wood fillers dispersed better in the PP matrix as the particle size decreased from 40 mesh to 100 mesh. The WPCs having the optimum mechanical and thermal properties were determined for 40 mesh heat-treated wood at 220°C and 20 wt-% loadings with PROMETHEE method.
- 9 July 2019
- Published by SAGE Publications in Plastics, Rubber and Composites: Macromolecular Engineering
- Vol. 48 (9) , 389-400
Mechanical, thermal and morphological properties of heat-treated wood-polypropylene composites and comparison of the composites with PROMETHEE method
The aim of the paper was to determine the mechanical, thermal, and morphological properties of heat-treated wood-polypropylene polymer composites (WPCs) and to select the composites having the optimum properties with the PROMETHEE method. In this study, polypropylene (PP) as a matrix, wood thermally treated at 180°C and 220°C as reinforcement filler were examined for preparing composites. The PP composites were compounded using a twin-screw extruder and test specimens were prepared by compression moulding. According to the test results, the thermal and mechanical properties of the WPCs generally increased with the addition of heat-treated wood fillers. The SEM images showed that the wood fillers dispersed better in the PP matrix as the particle size decreased from 40 mesh to 100 mesh. The WPCs having the optimum mechanical and thermal properties were determined for 40 mesh heat-treated wood at 220°C and 20 wt-% loadings with PROMETHEE method.
- 25 April 2019
- Published by Wiley in Polymer Composites
- Vol. 40 (11) , 4238-4247
Effects of halloysite nanotube on the performance of natural fiber filled poly(lactic acid) composites
Poly(lactic acid) (PLA) derived from renewable resources is an alternative to petroleum‐based polymers. In this work, natural fiber filled PLA‐halloysite nanotube (HNT) composites were prepared using melt blending followed by compression molding. Maleic anhydride grafted onto PLA (MA‐g‐PLA) was used to improve the interfacial bonding quality between hydrophobic and hydrophilic phases in the natural fiber filled PLA‐HNT composites. The performance properties of the natural fiber filled PLA‐HNT composites were characterized by tensile, flexural and impact tests, thermogravimetric analysis, differential scanning calorimetry (DSC), and scanning electron microscopy (SEM). DSC results showed that the loading of HNT could promote cold crystallization, and the improvement of crystallinity of the PLA‐HNT composites was by 16% with the addition of MA‐g‐PLA. The flexural and impact strengths of PLA‐HNT composites were not affected adversely up to 10 phr of HNT loading, but tensile strength of PLA‐HNT composites decreased gradually. In addition, numerous agglomerates of the nanotubes for PLA‐HNT composites with 15 phr loading of HNT were detected with SEM micrographs. However, moduli of elasticity of PLA‐HNT composites enhanced by 40% with increment of HNT loading in polymer matrix. Based on the findings, HNT could be used as nanofiller up to 10 phr in PLA matrix.
- 25 April 2019
- Published by Wiley in Polymer Composites
- Vol. 40 (11) , 4238-4247
Effects of halloysite nanotube on the performance of natural fiber filled poly(lactic acid) composites
Poly(lactic acid) (PLA) derived from renewable resources is an alternative to petroleum‐based polymers. In this work, natural fiber filled PLA‐halloysite nanotube (HNT) composites were prepared using melt blending followed by compression molding. Maleic anhydride grafted onto PLA (MA‐g‐PLA) was used to improve the interfacial bonding quality between hydrophobic and hydrophilic phases in the natural fiber filled PLA‐HNT composites. The performance properties of the natural fiber filled PLA‐HNT composites were characterized by tensile, flexural and impact tests, thermogravimetric analysis, differential scanning calorimetry (DSC), and scanning electron microscopy (SEM). DSC results showed that the loading of HNT could promote cold crystallization, and the improvement of crystallinity of the PLA‐HNT composites was by 16% with the addition of MA‐g‐PLA. The flexural and impact strengths of PLA‐HNT composites were not affected adversely up to 10 phr of HNT loading, but tensile strength of PLA‐HNT composites decreased gradually. In addition, numerous agglomerates of the nanotubes for PLA‐HNT composites with 15 phr loading of HNT were detected with SEM micrographs. However, moduli of elasticity of PLA‐HNT composites enhanced by 40% with increment of HNT loading in polymer matrix. Based on the findings, HNT could be used as nanofiller up to 10 phr in PLA matrix.
- 1 January 2018
- Published by Taylor & Francis in International Journal of Polymer Analysis and Characterization
- Vol. 23 (1) , 89-98
Effects of MA-g-PP and lignocellulosic filler addition on several properties of poly(L-lactic acid)/polypropylene composites
The aim of this study was to investigate the effects of maleic anhydride-graft-polypropylene (MA-g-PP) as a compatibilizer and wood fiber as a lignocellulosic filler on technical properties of poly(l-lactic acid) (PLLA)/polypropylene composites. The obtained composites were characterized through mechanical tests, thermogravimetric analysis, differential scanning analyzer, and chemical analysis via Fourier transform infrared spectroscopy (FTIR), and scanning electron microscope (SEM). The obtained results showed that the mechanical properties of the composites containing MA-g-PP were higher than those of the composites without MA-g-PP. SEM images revealed that the morphological properties of the composites including PP and PLLA were improved. The chemical interactions between PP and PLLA were demonstrated through FTIR results of composites with MA-g-PP.
- 1 January 2018
- Published by Taylor & Francis in International Journal of Polymer Analysis and Characterization
- Vol. 23 (1) , 89-98
Effects of MA-g-PP and lignocellulosic filler addition on several properties of poly(L-lactic acid)/polypropylene composites
The aim of this study was to investigate the effects of maleic anhydride-graft-polypropylene (MA-g-PP) as a compatibilizer and wood fiber as a lignocellulosic filler on technical properties of poly(l-lactic acid) (PLLA)/polypropylene composites. The obtained composites were characterized through mechanical tests, thermogravimetric analysis, differential scanning analyzer, and chemical analysis via Fourier transform infrared spectroscopy (FTIR), and scanning electron microscope (SEM). The obtained results showed that the mechanical properties of the composites containing MA-g-PP were higher than those of the composites without MA-g-PP. SEM images revealed that the morphological properties of the composites including PP and PLLA were improved. The chemical interactions between PP and PLLA were demonstrated through FTIR results of composites with MA-g-PP.