Behrouz Arab
Research Subjects
Behrouz Arab has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
Ali Shokuhfar
Advanced Materials and Nanotechnology Research Lab, Faculty of Mechanical Engineering, K. N. Toosi University of Technology, Tehran, Iran
2 shared publications- Ghasem Alahyarizadeh
Faculty of Engineering, Shahid Beheshti University, Tehran, Iran
2 shared publications Jafar Amraei
Composite Materials and Technology Center Tehran Iran
2 shared publicationsMajid Sohrabian
2 shared publications- Majid Vaseghi
Faculty of Mechanical and Energy Engineering, Shahid Beheshti University, Tehran, Iran
2 shared publications A. Shokuhfar
KN Toosi Univ Technol, Fac Mech Engn, Adv Mat & Nanotechnol Res Lab, Tehran, Iran
1 shared publication
Latest Publications
- Open Access
- 13 June 2025
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 59 (30) , 3367-3379
Ageing of carbon fibre-reinforced polymers (CFRPs) under hygro-thermal-salt conditions
We investigated the ageing of carbon fibre-reinforced polymers (CFRPs) subject to hygro-thermal-salt conditions. Firstly, we manufactured a series of uni-directional (UD) CFRP specimens and exposed them to various hygro-thermal-salt conditions containing elevated temperatures and salinities in aqueous environments for a length of three and 6 months. Following this, we characterised the performance of the UD CFRP under tensile, compression and shear loadings in both longitudinal and transverse fibre directions. Additionally, we manufactured epoxy polymer samples and exposed them to the same environmental conditions as those of CFRPs to evaluate their response under tensile loading and to better understand the degradation of the polymer constituent and its role in the performance of CFRPs subject to hygro-thermal-salt ageing conditions. Following this experimental campaign, we performed MD simulations on the monolithic epoxy polymer to obtain more insights into ageing and possibly explain mechanisms of the performance degradation that are difficult to explain solely by experiments. The experimental results demonstrate that over a 6-month period, the presence and combination of water, heat and salt can reduce: the tensile strength and Young modulus of the monolithic epoxy polymer by 31% and 17%, respectively; the longitudinal tensile strength and Young modulus of CFRPs by 15% and 3%, respectively; and the transverse tensile strength and Young modulus of CFRPs by 50% and 6%, respectively. MD simulations reveal that the presence of water reduced the glass transition temperature of the epoxy polymer.
- 13 June 2025
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 59 (30) , 3367-3379
Open AccessAgeing of carbon fibre-reinforced polymers (CFRPs) under hygro-thermal-salt conditions
We investigated the ageing of carbon fibre-reinforced polymers (CFRPs) subject to hygro-thermal-salt conditions. Firstly, we manufactured a series of uni-directional (UD) CFRP specimens and exposed them to various hygro-thermal-salt conditions containing elevated temperatures and salinities in aqueous environments for a length of three and 6 months. Following this, we characterised the performance of the UD CFRP under tensile, compression and shear loadings in both longitudinal and transverse fibre directions. Additionally, we manufactured epoxy polymer samples and exposed them to the same environmental conditions as those of CFRPs to evaluate their response under tensile loading and to better understand the degradation of the polymer constituent and its role in the performance of CFRPs subject to hygro-thermal-salt ageing conditions. Following this experimental campaign, we performed MD simulations on the monolithic epoxy polymer to obtain more insights into ageing and possibly explain mechanisms of the performance degradation that are difficult to explain solely by experiments. The experimental results demonstrate that over a 6-month period, the presence and combination of water, heat and salt can reduce: the tensile strength and Young modulus of the monolithic epoxy polymer by 31% and 17%, respectively; the longitudinal tensile strength and Young modulus of CFRPs by 15% and 3%, respectively; and the transverse tensile strength and Young modulus of CFRPs by 50% and 6%, respectively. MD simulations reveal that the presence of water reduced the glass transition temperature of the epoxy polymer.
- 23 May 2024
- Published by Elsevier in Computational Materials Science
- Vol. 243
Molecular dynamics study on mechanical properties of polycaprolactone/bioactive glass nanocomposites
- 23 May 2024
- Published by Elsevier in Computational Materials Science
- Vol. 243
Molecular dynamics study on mechanical properties of polycaprolactone/bioactive glass nanocomposites
- 1 July 2020
- Published by Elsevier in Computational Materials Science
- Vol. 180, 109710
Molecular dynamics simulation of enhanced heat transfer through conical Al/Cu nanostructures
- 1 July 2020
- Published by Elsevier in Computational Materials Science
- Vol. 180, 109710
Molecular dynamics simulation of enhanced heat transfer through conical Al/Cu nanostructures
- 15 June 2019
- Published by Springer Nature in Journal of Molecular Modeling
- Vol. 25 (7) , 191
Mechanical properties of carbon nanotube- and graphene-reinforced Araldite LY/Aradur HY 5052 resin epoxy composites: a molecular dynamics study
Mechanical properties of graphene- and carbon nanotube-reinforced Araldite LY 5052/Aradur HY 5052 epoxy resins were investigated by molecular dynamics simulations. The COMPASS II force field was implemented in the simulations. Mechanical properties of the reinforced araldite/aradur resin epoxy system with CNT reveal the highest Young’s, bulk, and shear modulus alongside the lowest Poisson ratio for 4.5% wt CNT; as Young’s modulus was enhanced from 3.36 to 4.92 GPa. For values higher than 4.5% CNT, improving trend of properties ceases. This is due to the fact that in higher percentages of CNTs, agglomeration happens, which leads to the lower strength of the system. The results also indicated that by increasing weight percentage of CNT, the glass transition temperature of the system increases. Moreover, for higher diameters of CNT, not only have mechanical properties been improved but the glass transition temperature has also been enhanced. The results of the graphene-reinforced resin epoxy system imply that optimum desirable properties are acquired in lower concentrations of graphene. As in higher densities, the tendency of graphene sheets to form van der Waals bonds leads to the agglomeration in the system, worsening the properties. The sample with 8.8% graphene holds the highest values of Young’s and shear modulus, whereas the highest bulk modulus and lowest density is for the sample with 4.6% graphene. Glass transition temperatures of the samples increased by adding graphene overall. However, samples with more than 8.8% did not follow the same rising trend.
- 15 June 2019
- Published by Springer Nature in Journal of Molecular Modeling
- Vol. 25 (7) , 191
Mechanical properties of carbon nanotube- and graphene-reinforced Araldite LY/Aradur HY 5052 resin epoxy composites: a molecular dynamics study
Mechanical properties of graphene- and carbon nanotube-reinforced Araldite LY 5052/Aradur HY 5052 epoxy resins were investigated by molecular dynamics simulations. The COMPASS II force field was implemented in the simulations. Mechanical properties of the reinforced araldite/aradur resin epoxy system with CNT reveal the highest Young’s, bulk, and shear modulus alongside the lowest Poisson ratio for 4.5% wt CNT; as Young’s modulus was enhanced from 3.36 to 4.92 GPa. For values higher than 4.5% CNT, improving trend of properties ceases. This is due to the fact that in higher percentages of CNTs, agglomeration happens, which leads to the lower strength of the system. The results also indicated that by increasing weight percentage of CNT, the glass transition temperature of the system increases. Moreover, for higher diameters of CNT, not only have mechanical properties been improved but the glass transition temperature has also been enhanced. The results of the graphene-reinforced resin epoxy system imply that optimum desirable properties are acquired in lower concentrations of graphene. As in higher densities, the tendency of graphene sheets to form van der Waals bonds leads to the agglomeration in the system, worsening the properties. The sample with 8.8% graphene holds the highest values of Young’s and shear modulus, whereas the highest bulk modulus and lowest density is for the sample with 4.6% graphene. Glass transition temperatures of the samples increased by adding graphene overall. However, samples with more than 8.8% did not follow the same rising trend.
- 26 September 2018
- Published by Wiley in Polymer Composites
- Vol. 40 (S2) , E1219-E1234
Modeling the interphase region in carbon nanotube‐reinforced polymer nanocomposites
Carbon nanotubes are regarded as ideal fillers for polymeric materials due to their excellent mechanical properties. Mechanical analysis without consideration of nanotube–matrix interphase, may not give precise predictions. In this work, the impacts of interphase on the behavior of polymer‐based nanocomposites are studied. For this purpose, a closed‐form micromechanical interphase model considering the diameter of nanotube, the thickness of interphase, and mechanical properties of nanotube and polymer is proposed to estimate the overall mechanical properties of nanotube‐reinforced polymer nanocomposites. Furthermore, the effective elastic constants of the nanocomposites for a wide range of diameters and volume fractions of nanotubes, evaluated via the suggested interphase model, are compared with the results of molecular dynamics simulations. Thereafter, the effects of diameter, length and volume fraction of nanotubes on the mechanical properties of nanocomposites are investigated using the suggested model. The results indicate that mechanical properties of nanocomposites are significantly influenced by the interphase. POLYM. COMPOS., 40:E1219–E1234, 2019. © 2018 Society of Plastics Engineers
- 26 September 2018
- Published by Wiley in Polymer Composites
- Vol. 40 (S2) , E1219-E1234
Modeling the interphase region in carbon nanotube‐reinforced polymer nanocomposites
Carbon nanotubes are regarded as ideal fillers for polymeric materials due to their excellent mechanical properties. Mechanical analysis without consideration of nanotube–matrix interphase, may not give precise predictions. In this work, the impacts of interphase on the behavior of polymer‐based nanocomposites are studied. For this purpose, a closed‐form micromechanical interphase model considering the diameter of nanotube, the thickness of interphase, and mechanical properties of nanotube and polymer is proposed to estimate the overall mechanical properties of nanotube‐reinforced polymer nanocomposites. Furthermore, the effective elastic constants of the nanocomposites for a wide range of diameters and volume fractions of nanotubes, evaluated via the suggested interphase model, are compared with the results of molecular dynamics simulations. Thereafter, the effects of diameter, length and volume fraction of nanotubes on the mechanical properties of nanocomposites are investigated using the suggested model. The results indicate that mechanical properties of nanocomposites are significantly influenced by the interphase. POLYM. COMPOS., 40:E1219–E1234, 2019. © 2018 Society of Plastics Engineers
- 12 September 2018
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 53 (9) , 1261-1274
Effect of interphase zone on the overall elastic properties of nanoparticle-reinforced polymer nanocomposites
In the current work, the effect of interphase region on the mechanical properties of polymer nanocomposites reinforced with nanoparticles is studied. For this purpose, a closed-form interphase model as a function of radial distance based on finite-size representative volume element is suggested to estimate the mechanical properties of particle-reinforced nanocomposites. The effective Young’s and shear moduli of thermoplastic polycarbonate-based nanocomposites for a wide range of sizes and volume fractions of silicon carbide nanoparticles are investigated using the proposed interphase model and molecular dynamics simulations. In order to investigate the effect of particle size, several unit cells of the same volume fraction, but with different particle radii have been considered. The micromechanics-based homogenization results are in good agreement with the results of molecular dynamics simulations for all models. This study demonstrates that the suggested micromechanical interphase model has the capacity to estimate effective mechanical properties of polymer-based nanocomposites reinforced with spherical inclusions.
- 12 September 2018
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 53 (9) , 1261-1274
Effect of interphase zone on the overall elastic properties of nanoparticle-reinforced polymer nanocomposites
In the current work, the effect of interphase region on the mechanical properties of polymer nanocomposites reinforced with nanoparticles is studied. For this purpose, a closed-form interphase model as a function of radial distance based on finite-size representative volume element is suggested to estimate the mechanical properties of particle-reinforced nanocomposites. The effective Young’s and shear moduli of thermoplastic polycarbonate-based nanocomposites for a wide range of sizes and volume fractions of silicon carbide nanoparticles are investigated using the proposed interphase model and molecular dynamics simulations. In order to investigate the effect of particle size, several unit cells of the same volume fraction, but with different particle radii have been considered. The micromechanics-based homogenization results are in good agreement with the results of molecular dynamics simulations for all models. This study demonstrates that the suggested micromechanical interphase model has the capacity to estimate effective mechanical properties of polymer-based nanocomposites reinforced with spherical inclusions.
- 22 November 2016
- Published by Taylor & Francis
- p. 93-126
Chapter 7 Smart Coatings Including Antibacterial Coatings, Anti-Fogging Coatings and Self-Healing Materials
- 22 November 2016
- Published by Taylor & Francis
- p. 93-126
Chapter 7 Smart Coatings Including Antibacterial Coatings, Anti-Fogging Coatings and Self-Healing Materials
- 1 November 2016
- Vol. 3 (2) , 113-121
Mechanical Properties of CNT-Reinforced Polymer Nano-composites: A Molecular Dynamics Study
- 1 November 2016
- Vol. 3 (2) , 113-121
Mechanical Properties of CNT-Reinforced Polymer Nano-composites: A Molecular Dynamics Study