Rozana Mohd Dahan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rozana Mohd Dahan has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Mohamad Hafiz Mohd Wahid
Universiti Teknologi MARA
17 shared publications - Adillah Nurashikin Arshad
Universiti Teknologi MARA (UiTM)
10 shared publications Muhamad Naiman Sarip
Universiti Teknologi MARA (UiTM)
9 shared publicationsMohamad Rusop Mahmood
NANO-ElecTronic Centre (NET), Faculty of Electrical Engineering, Universiti Teknologi MARA (UiTM), Shah Alam, Malaysia
6 shared publications- Wan Haliza Abdul Majid
Low Dimensional Materials Research Centre, Department of Physics, Faculty of Science, University of Malaya, Kuala Lumpur 50603, Malaysia
6 shared publications M. Rusop
NANO-Electronic Centre, Faculty of Electrical Engineering, Universiti Teknologi MARA (UiTM), 40450, Shah Alam, Selangor, Malaysia
5 shared publications
Latest Publications
- Open Access
- 21 April 2019
- Published by Wiley in Journal of Nanomaterials
- Vol. 2019, 1-12
Dielectric and Structural Properties of Poly(vinylidene fluoride) (PVDF) and Poly(vinylidene fluoride-trifluoroethylene) (PVDF-TrFE) Filled with Magnesium Oxide Nanofillers
This study examines the dielectric properties of filled PVDF film and filled PVDF-TrFE film incorporated with 1, 3, 5, and 7 weight percentages of magnesium oxide (MgO) nanofillers. The metal-insulator-metal (MIM) configuration demonstrates PVDF/MgO with 7 weight percent of MgO which produced high dielectric constant (1 kHz) with low dielectric loss. The ATR-FTIR spectra of PVDF/MgO (7%) indicate wide bonding peaks at 840 cm-1 and 880 cm-1, assigned to -CH2 and -CF2 groups, respectively. This implies the presence of high content of β-crystals in the PVDF/MgO (7%) film. A shift in the peak was observed in the same film, from 1170 cm-1 to 1180 cm-1 suggesting possible transformation from γ-crystals to β-crystals. This film showed no apparent defect on its film surface. Thus, it established that PVDF incorporated with 7% MgO can be used to produce nanocomposite thin film for low-frequency electronic devices.
- 21 April 2019
- Published by Wiley in Journal of Nanomaterials
- Vol. 2019, 1-12
Open AccessDielectric and Structural Properties of Poly(vinylidene fluoride) (PVDF) and Poly(vinylidene fluoride-trifluoroethylene) (PVDF-TrFE) Filled with Magnesium Oxide Nanofillers
This study examines the dielectric properties of filled PVDF film and filled PVDF-TrFE film incorporated with 1, 3, 5, and 7 weight percentages of magnesium oxide (MgO) nanofillers. The metal-insulator-metal (MIM) configuration demonstrates PVDF/MgO with 7 weight percent of MgO which produced high dielectric constant (1 kHz) with low dielectric loss. The ATR-FTIR spectra of PVDF/MgO (7%) indicate wide bonding peaks at 840 cm-1 and 880 cm-1, assigned to -CH2 and -CF2 groups, respectively. This implies the presence of high content of β-crystals in the PVDF/MgO (7%) film. A shift in the peak was observed in the same film, from 1170 cm-1 to 1180 cm-1 suggesting possible transformation from γ-crystals to β-crystals. This film showed no apparent defect on its film surface. Thus, it established that PVDF incorporated with 7% MgO can be used to produce nanocomposite thin film for low-frequency electronic devices.
- 22 May 2017
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 3 (3) , 300-307
Structural and electrical properties of PVDF-TrFE/ZnO bilayer and filled PVDF-TrFE /ZnO single layer nanocomposite films
This study investigates the effect of ZnO nanofillers loading ratios on Polyvinylideneflouride-Triflouroethylene/Zinc Oxide (PVDF-TrFE/ZnO) nanocomposites thin films; filled single layer and bilayer film. Both films were produced using a spin coater with ZnO nanofillers of weight percentages 1, 3, 5 and 7%. These films were characterized for their crystal phase change via ATR-FTIR and electrical properties using I-V measurement. The ATR-FTIR for both single layer and bilayer nanocomposites films showed three distinguished peaks at absorption bands of 1400, 1290 and 848 cm−1, evident of the β-phase PVDF-TrFE crystals. The resistivity value recorded for the bilayer PVDF-TrFE/ZnO nanocomposites thin films were significantly higher in comparison to the filled single layer PVDF-TrFE/ZnO nanocomposites film. At 1 wt%, the resistivity value for PVDF-TrFE/ZnO bilayer thin film was 4.34 × 105 Ω cm, relative to 1.50 × 105 Ω cm resistivity value, for the single layer film. Therefore, it is established in this study that PVDF-TrFE/ZnO bilayer film showed enhanced resistivity property at small loading percentage of ZnO nanofillers, suggests that the bilayer film is suitable to be utilized as a dielectric film for storage devices.
- 22 May 2017
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 3 (3) , 300-307
Structural and electrical properties of PVDF-TrFE/ZnO bilayer and filled PVDF-TrFE /ZnO single layer nanocomposite films
This study investigates the effect of ZnO nanofillers loading ratios on Polyvinylideneflouride-Triflouroethylene/Zinc Oxide (PVDF-TrFE/ZnO) nanocomposites thin films; filled single layer and bilayer film. Both films were produced using a spin coater with ZnO nanofillers of weight percentages 1, 3, 5 and 7%. These films were characterized for their crystal phase change via ATR-FTIR and electrical properties using I-V measurement. The ATR-FTIR for both single layer and bilayer nanocomposites films showed three distinguished peaks at absorption bands of 1400, 1290 and 848 cm−1, evident of the β-phase PVDF-TrFE crystals. The resistivity value recorded for the bilayer PVDF-TrFE/ZnO nanocomposites thin films were significantly higher in comparison to the filled single layer PVDF-TrFE/ZnO nanocomposites film. At 1 wt%, the resistivity value for PVDF-TrFE/ZnO bilayer thin film was 4.34 × 105 Ω cm, relative to 1.50 × 105 Ω cm resistivity value, for the single layer film. Therefore, it is established in this study that PVDF-TrFE/ZnO bilayer film showed enhanced resistivity property at small loading percentage of ZnO nanofillers, suggests that the bilayer film is suitable to be utilized as a dielectric film for storage devices.
- 9 May 2016
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 78 (5-5)
FLEXURAL PROPERTIES OF COMPRESSION MOULDED KENAF POLYETHYLENE COMPOSITE
The use of natural fibres at high percentages of loading in thermoplastic composites for the production of sustainable and green materials in consumer goods, furniture, automotive industry and construction industry is encourage. Several studies have been conducted by many researchers to improve the mechanical properties of the fibres and the fibre-matrix interface for better bonding and load transfer especially when high fibre loading is used. The natural fibre hydrophilic properties make the poor interface and poor resistance to moisture absorption when used to reinforce hydrophobic matrices. Therefore, this study investigates the effects of different surface treatment of kenaf bast fibre on the flexural strength of kenaf polyethylene composite (KPC). These composites, made using high-density polyethylene (HDPE) as the matrix polymer, kenaf core and kenaf bast fibre as the reinforcing filler at different percentages of filler and maleic anhydride grafted polyethylene (MAPE) as compatibilizing agents. Overall, KPCs with bast fibre treated with 0.06M MgCl2 and 0.06M NaOH enhanced the flexural strength of the composites as compared to untreated bast fibre in the composite. Besides, the flexural properties of the KPCs significantly decreased with increasing kenaf bast fibre content, due to the reduction of interface bond between the fibre and matrix.
- 9 May 2016
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 78 (5-5)
FLEXURAL PROPERTIES OF COMPRESSION MOULDED KENAF POLYETHYLENE COMPOSITE
The use of natural fibres at high percentages of loading in thermoplastic composites for the production of sustainable and green materials in consumer goods, furniture, automotive industry and construction industry is encourage. Several studies have been conducted by many researchers to improve the mechanical properties of the fibres and the fibre-matrix interface for better bonding and load transfer especially when high fibre loading is used. The natural fibre hydrophilic properties make the poor interface and poor resistance to moisture absorption when used to reinforce hydrophobic matrices. Therefore, this study investigates the effects of different surface treatment of kenaf bast fibre on the flexural strength of kenaf polyethylene composite (KPC). These composites, made using high-density polyethylene (HDPE) as the matrix polymer, kenaf core and kenaf bast fibre as the reinforcing filler at different percentages of filler and maleic anhydride grafted polyethylene (MAPE) as compatibilizing agents. Overall, KPCs with bast fibre treated with 0.06M MgCl2 and 0.06M NaOH enhanced the flexural strength of the composites as compared to untreated bast fibre in the composite. Besides, the flexural properties of the KPCs significantly decreased with increasing kenaf bast fibre content, due to the reduction of interface bond between the fibre and matrix.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1733 (1) , 020054
Fabrication of PVDF-TrFE based bilayered PbTiO3/PVDF-TrFE films capacitor
Development of high performance capacitor is reaching towards new generation where the ferroelectric materials take places as the active dielectric layer. The motivation of this study is to produce high capacitance device with long life cycle. This was configured by preparing bilayered films where lead titanate as an active dielectric layer and stacked with the top dielectric layer, poly(vinyledenefluoride-trifluoroethylene). Both of them are being referred that have one in common which is ferroelectric behavior. Therefore the combination of ceramic and polymer ferroelectric material could perform optimum dielectric characteristic for capacitor applications. The fabrication was done by simple sol-gel spin coating method that being varied at spinning speed property for polymer layers, whereas maintaining the ceramic layer. The characterization of PVDF-TrFE/PbTiO3 was performed according to metal-insulator-metal stacked capacitor measurement which includes structural, dielectric, and ferroelectric measurement.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1733 (1) , 020054
Fabrication of PVDF-TrFE based bilayered PbTiO3/PVDF-TrFE films capacitor
Development of high performance capacitor is reaching towards new generation where the ferroelectric materials take places as the active dielectric layer. The motivation of this study is to produce high capacitance device with long life cycle. This was configured by preparing bilayered films where lead titanate as an active dielectric layer and stacked with the top dielectric layer, poly(vinyledenefluoride-trifluoroethylene). Both of them are being referred that have one in common which is ferroelectric behavior. Therefore the combination of ceramic and polymer ferroelectric material could perform optimum dielectric characteristic for capacitor applications. The fabrication was done by simple sol-gel spin coating method that being varied at spinning speed property for polymer layers, whereas maintaining the ceramic layer. The characterization of PVDF-TrFE/PbTiO3 was performed according to metal-insulator-metal stacked capacitor measurement which includes structural, dielectric, and ferroelectric measurement.
- 1 December 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 418-421
Impedance and structural property of bilayer films PbTiO3/PVDF-TrFE for capacitor applications
Hybrid composited material like polymer-ceramic will improve the reliability factor of the device. Yet, the motivation still goes on to produce high performance device. In this study, the impedance analysis on bilayer films lead titanate and poly(vinyledenefluoride-trifluoroethylene) yield to the semicircle cole-cole plot with added slanted spike results. This presents the double layer capacitance which occurred between dielectrc-electrode. The bilayer films obtains about ~105Ω which determines the films are high resistive dielectric material. The bilayer films were fabricated at maximum of 105 nm thickness on top of electrode coated glass substrate. Structural property of bilayer films obtain distinguish behavior compared to the single layer films. Moreover, the line profile observed on each layer presents low surface roughness for bilayer prepared films. Thus, this study highlights the importance of bilayer films denoted for capacitor application.
- 1 December 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 418-421
Impedance and structural property of bilayer films PbTiO3/PVDF-TrFE for capacitor applications
Hybrid composited material like polymer-ceramic will improve the reliability factor of the device. Yet, the motivation still goes on to produce high performance device. In this study, the impedance analysis on bilayer films lead titanate and poly(vinyledenefluoride-trifluoroethylene) yield to the semicircle cole-cole plot with added slanted spike results. This presents the double layer capacitance which occurred between dielectrc-electrode. The bilayer films obtains about ~105Ω which determines the films are high resistive dielectric material. The bilayer films were fabricated at maximum of 105 nm thickness on top of electrode coated glass substrate. Structural property of bilayer films obtain distinguish behavior compared to the single layer films. Moreover, the line profile observed on each layer presents low surface roughness for bilayer prepared films. Thus, this study highlights the importance of bilayer films denoted for capacitor application.
- 18 June 2015
- Published by Springer Nature in JOM
- Vol. 67 (12) , 2869-2876
Structural and Electrical Properties of Sol–Gel-Derived Lead Titanate Nanofilms with Different Pb Contents for MIM Capacitors
- 18 June 2015
- Published by Springer Nature in JOM
- Vol. 67 (12) , 2869-2876
Structural and Electrical Properties of Sol–Gel-Derived Lead Titanate Nanofilms with Different Pb Contents for MIM Capacitors
- 1 January 2015
- Published by Inderscience Publishers in International Journal of Materials Engineering Innovation
- Vol. 6 (2/3) , 130
Ferroelectric characteristics of ZnO/MgO-based organic capacitor
Magnesium oxide, MgO with nanometre dimension particles size (36 to 73 nm) was successfully deposited on cleaned glass substrate. The drying temperatures were varied from 100 to 300°C and the dielectrics behaviour was investigated. From the results, it was revealed that variation of nano-MgO films properties obtained by changing the drying temperature. Nano-MgO film dried at 200°C was found to be a good dielectric layer due to it structural properties that resulted in the enhancement of relative permittivity value. The electrical properties shows better in dielectric layer characteristic where the resistivity was found to be 12.8 × 104 Ω.cm with leakage current density of 10
- 1 January 2015
- Published by Inderscience Publishers in International Journal of Materials Engineering Innovation
- Vol. 6 (2/3) , 130
Ferroelectric characteristics of ZnO/MgO-based organic capacitor
Magnesium oxide, MgO with nanometre dimension particles size (36 to 73 nm) was successfully deposited on cleaned glass substrate. The drying temperatures were varied from 100 to 300°C and the dielectrics behaviour was investigated. From the results, it was revealed that variation of nano-MgO films properties obtained by changing the drying temperature. Nano-MgO film dried at 200°C was found to be a good dielectric layer due to it structural properties that resulted in the enhancement of relative permittivity value. The electrical properties shows better in dielectric layer characteristic where the resistivity was found to be 12.8 × 104 Ω.cm with leakage current density of 10
- Open Access
- 22 August 2014
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 64
Electrical Characterization of Metal-Ferroelectric-Insulator- Semiconductor having Double Layered Insulator for Memory Applications
- 22 August 2014
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 64
Open AccessElectrical Characterization of Metal-Ferroelectric-Insulator- Semiconductor having Double Layered Insulator for Memory Applications
- 13 February 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 895, 138-141
Effect of Exposure Time on Plasma Modified Polyvinylidenefluoride-Trifluoroethylene (PVDF-TrFE) Film Surfaces
This study investigates the plasma surface modified spin coated PVDF-TrFE (70/30) film of 200nm thick using Atomic Force Microscopy (AFM), Water Contact Angle (WCA) and Fourier Transform Infrared Spectroscopy (FTIR). The surface of the spin coated PVDF-TrFE film were modified using 13.56 MHz rf Argon plasma. The exposure time of the charged particle on PVDF-TrFE films were varied for 1, 3, 5, 7 and 9mins. Prior to modification, the average surface roughness observed was 3.5nm. However upon modification, the surface roughness was increased to 9.5nm. The contact angle of the surface modified film was reduced from 89° to 58°. The increase in surface roughness and wettability of the modified film provided good biocompatibility. This finding created great interest in developing functional polymer suitable for applications in areas such are biomedical, bio-analytical assays, textile and even food industry.
- 13 February 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 895, 138-141
Effect of Exposure Time on Plasma Modified Polyvinylidenefluoride-Trifluoroethylene (PVDF-TrFE) Film Surfaces
This study investigates the plasma surface modified spin coated PVDF-TrFE (70/30) film of 200nm thick using Atomic Force Microscopy (AFM), Water Contact Angle (WCA) and Fourier Transform Infrared Spectroscopy (FTIR). The surface of the spin coated PVDF-TrFE film were modified using 13.56 MHz rf Argon plasma. The exposure time of the charged particle on PVDF-TrFE films were varied for 1, 3, 5, 7 and 9mins. Prior to modification, the average surface roughness observed was 3.5nm. However upon modification, the surface roughness was increased to 9.5nm. The contact angle of the surface modified film was reduced from 89° to 58°. The increase in surface roughness and wettability of the modified film provided good biocompatibility. This finding created great interest in developing functional polymer suitable for applications in areas such are biomedical, bio-analytical assays, textile and even food industry.
- 13 February 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 895, 221-225
The Effect of Annealing Temperatures on the Dielectric Constant of PVDF/MgO Nanocomposites Thin Films
Poly(vinylidene flouride)/nano-magnesium oxide (PVDF/MgO) nanocomposites with MgO loading percentage of (7% wt. %) were annealed with various annealing temperatures ranging from 70°C to 170°C with rapid removal from the oven. From dielectric constant, the samples annealed at temperature of 70°C showed an improvement in the dielectric constant from 21 to 23 at frequency 103 Hz for UN and AN70 respectively. However, as the temperatures were increased, the dielectric constant of PVDF/MgO (7%) was found to decrease. XRD showed the presence of β-phase for PVDF/MgO(7%) sample annealed at 70°C in comparison to unannealed sample, hence PVDF/MgO(7%) film is suitable to be used for low frequency capacitor application.
- 13 February 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 895, 221-225
The Effect of Annealing Temperatures on the Dielectric Constant of PVDF/MgO Nanocomposites Thin Films
Poly(vinylidene flouride)/nano-magnesium oxide (PVDF/MgO) nanocomposites with MgO loading percentage of (7% wt. %) were annealed with various annealing temperatures ranging from 70°C to 170°C with rapid removal from the oven. From dielectric constant, the samples annealed at temperature of 70°C showed an improvement in the dielectric constant from 21 to 23 at frequency 103 Hz for UN and AN70 respectively. However, as the temperatures were increased, the dielectric constant of PVDF/MgO (7%) was found to decrease. XRD showed the presence of β-phase for PVDF/MgO(7%) sample annealed at 70°C in comparison to unannealed sample, hence PVDF/MgO(7%) film is suitable to be used for low frequency capacitor application.