Mikael Perrut
Research Subjects
Mikael Perrut has a total of 83 co-authors. Here are the top co-authors by number of shared publications:
- Sabine Bottin-Rousseau
Sorbonne Universite
6 shared publications Gabriel Faivre
5 shared publications- Silvère Akamatsu
Sorbonne Universite
3 shared publications Alain Couret
2 shared publicationsM.H. Mathon
2 shared publicationsSilvère Akamatsu
2 shared publications
Latest Publications
- Open Access
- 28 August 2024
- Published by Springer Nature in High Temperature Corrosion of Materials
- Vol. 101 (5) , 1249-1262
Design of Oxidation-Resistant Alloys Using Combinatorial Approaches with Chemically Graded Materials
This work introduces a new high-throughput method to characterize the oxidation behavior of chemically graded Ni-based alloys in order to feed databases destined to numerical metallurgy approaches. A Ni–wCr–3Al (w ∈ [0, 30]) chemically graded material was obtained from two homogeneous samples by a diffusion couple method at 1300 °C for 100 h. The composition range was selected in order to observe the three types of oxidation behavior identified in the reference work of Giggins and Pettit (Giggins and Pettit in Journal of The Electrochemical Society 118:1782, 1971). The excellent agreement between simulated and experimental diffusion profiles validated the experimental method used to manufacture the chemically graded material (CGM). The CGM was then oxidized at 1200 °C in air. Surface and cross-section characterization was conducted by SEM/EDS and Raman spectroscopy to identify the oxides formed on the CGM. To accelerate the Raman characterization treatment, a method linking principal component analysis and K-means unsupervised clustering algorithm was developed. It allowed for the identification of the oxide type without peak indexation issues and is well suited for CGM. These results show that results similar to well-recognized reference experiments (Giggins and Pettit in Journal of The Electrochemical Society 118:1782, 1971) can be achieved using only one CGM.
- 28 August 2024
- Published by Springer Nature in High Temperature Corrosion of Materials
- Vol. 101 (5) , 1249-1262
Open AccessDesign of Oxidation-Resistant Alloys Using Combinatorial Approaches with Chemically Graded Materials
This work introduces a new high-throughput method to characterize the oxidation behavior of chemically graded Ni-based alloys in order to feed databases destined to numerical metallurgy approaches. A Ni–wCr–3Al (w ∈ [0, 30]) chemically graded material was obtained from two homogeneous samples by a diffusion couple method at 1300 °C for 100 h. The composition range was selected in order to observe the three types of oxidation behavior identified in the reference work of Giggins and Pettit (Giggins and Pettit in Journal of The Electrochemical Society 118:1782, 1971). The excellent agreement between simulated and experimental diffusion profiles validated the experimental method used to manufacture the chemically graded material (CGM). The CGM was then oxidized at 1200 °C in air. Surface and cross-section characterization was conducted by SEM/EDS and Raman spectroscopy to identify the oxides formed on the CGM. To accelerate the Raman characterization treatment, a method linking principal component analysis and K-means unsupervised clustering algorithm was developed. It allowed for the identification of the oxide type without peak indexation issues and is well suited for CGM. These results show that results similar to well-recognized reference experiments (Giggins and Pettit in Journal of The Electrochemical Society 118:1782, 1971) can be achieved using only one CGM.
- 1 September 2020
- Published by Elsevier in Intermetallics
- Vol. 124
Effect of Mo, Ta, V and Zr on a duplex bcc+orthorhombic refractory complex concentrated alloy using diffusion couples
- 1 September 2020
- Published by Elsevier in Intermetallics
- Vol. 124
Effect of Mo, Ta, V and Zr on a duplex bcc+orthorhombic refractory complex concentrated alloy using diffusion couples
- 29 August 2020
- Published by Springer Nature
- p. 31-40
Development of AGAT, a Third-Generation Nickel-Based Superalloy for Single Crystal Turbine Blade Applications
- 29 August 2020
- Published by Springer Nature
- p. 31-40
Development of AGAT, a Third-Generation Nickel-Based Superalloy for Single Crystal Turbine Blade Applications
- 1 April 2020
- Published by Elsevier in Acta Materialia
- Vol. 187, 41-50
Instabilities in the periodic arrangement of elastically interacting precipitates in nickel-base superalloys
- 1 April 2020
- Published by Elsevier in Acta Materialia
- Vol. 187, 41-50
Instabilities in the periodic arrangement of elastically interacting precipitates in nickel-base superalloys
- Top Cited PapersOpen Access
- 15 October 2018
- Published by MathDoc/Centre Mersenne in Comptes Rendus. Physique
- Vol. 19 (8) , 657-671
High temperature materials for aerospace applications: Ni-based superalloys and γ-TiAl alloys
Two outstanding aerospace-oriented high-temperature materials, the single-crystal nickel-based superalloys for high-pressure turbine blades and the γ-TiAl-based alloys for low pressure turbine blades, are being presented here. In both cases, the optimisation of their mechanical properties is based on a high knowledge of metallurgy, mixing together different aspects such as processes, alloy design, deformation mechanisms, impact of oxidative environment or interaction between protective layers and protected alloy. Historical evolutions are recalled and put into perspective with more recent research activities.
- 15 October 2018
- Published by MathDoc/Centre Mersenne in Comptes Rendus. Physique
- Vol. 19 (8) , 657-671
Top Cited PapersOpen AccessHigh temperature materials for aerospace applications: Ni-based superalloys and γ-TiAl alloys
Two outstanding aerospace-oriented high-temperature materials, the single-crystal nickel-based superalloys for high-pressure turbine blades and the γ-TiAl-based alloys for low pressure turbine blades, are being presented here. In both cases, the optimisation of their mechanical properties is based on a high knowledge of metallurgy, mixing together different aspects such as processes, alloy design, deformation mechanisms, impact of oxidative environment or interaction between protective layers and protected alloy. Historical evolutions are recalled and put into perspective with more recent research activities.
- 23 May 2018
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 49 (9) , 3854-3864
γ′ Precipitation Study of a Co-Ni-Based Alloy
- 23 May 2018
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 49 (9) , 3854-3864
γ′ Precipitation Study of a Co-Ni-Based Alloy
- 1 March 2018
- Published by Elsevier in Intermetallics
- Vol. 94, 29-37
Effect of Au diffusion in Au-coated (γ + α2) titanium aluminides
- 1 March 2018
- Published by Elsevier in Intermetallics
- Vol. 94, 29-37
Effect of Au diffusion in Au-coated (γ + α2) titanium aluminides
- 3 May 2016
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 33 (4-5) , 542-548
Influence of Si and C additions on microstructure and mechanical properties of the Ti-43.5Al-1Mo-4Nb-0.1B alloy
Separate effects of 0.3 at% Si and 0.2 at% C additions have been investigated on the Ti–43.5Al–1Mo–4Nb–0.1B alloy. Both elements appear to stabilise the γ phase. Si addition induces an increase in both γ-lamellar and γ-grain volume fractions. A heterogeneous distribution of primary and secondary silicides is observed in Al-rich regions of the microstructure, but silicon appears to be mainly in solid solution in the lamellar structure. The solid solution effect of silicon in the more plastically deformable β phase is probably very limited because of the high volume fraction of α2 in this alloy. This may explain the lack of beneficial effect of 0.3 at% of silicon on both tensile and creep properties. Carbon appears to stabilise the γ phase through an increase in γ-grain volume fraction and is found to be in solid solution in the lamellar structure. Our results suggest a very strong solid solution effect of carbon, since addition as low as 0.16 at% leads to an increase in yield strength at room and high temperature, a reduction in the secondary creep rate and a longer creep life.
- 3 May 2016
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 33 (4-5) , 542-548
Influence of Si and C additions on microstructure and mechanical properties of the Ti-43.5Al-1Mo-4Nb-0.1B alloy
Separate effects of 0.3 at% Si and 0.2 at% C additions have been investigated on the Ti–43.5Al–1Mo–4Nb–0.1B alloy. Both elements appear to stabilise the γ phase. Si addition induces an increase in both γ-lamellar and γ-grain volume fractions. A heterogeneous distribution of primary and secondary silicides is observed in Al-rich regions of the microstructure, but silicon appears to be mainly in solid solution in the lamellar structure. The solid solution effect of silicon in the more plastically deformable β phase is probably very limited because of the high volume fraction of α2 in this alloy. This may explain the lack of beneficial effect of 0.3 at% of silicon on both tensile and creep properties. Carbon appears to stabilise the γ phase through an increase in γ-grain volume fraction and is found to be in solid solution in the lamellar structure. Our results suggest a very strong solid solution effect of carbon, since addition as low as 0.16 at% leads to an increase in yield strength at room and high temperature, a reduction in the secondary creep rate and a longer creep life.
- 2 May 2016
- Published by Wiley
- p. 1237-1242
Silicide Precipitation in Silicon‐Doped γiAl Alloys