Yonggang Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yonggang Wang has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
- Song Jiang
University of Shanghai for Science and Technology
28 shared publications - Zi Li
Department of Electrical Engineering, School of Mechanical Engineering, University of Shanghai for Science and Technology, Shanghai, China
20 shared publications - Junfeng Rao
University of Science and Technology of China
15 shared publications - Zhonghang Wu
Shanghai University of Medicine and Health Sciences
10 shared publications - Liuxia Li
Huazhong University of Science and Technology
4 shared publications Qian Qu
Department of Nuclear Medicine, School of Medicine, Ruijin Hospital, Shanghai Jiaotong University, Shanghai, China
4 shared publications
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 54  (11) , 5918-5925
Research on Water Treatment by Liquid-Phase Discharge Plasma Synergistic With UVC
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 54  (11) , 5918-5925
Research on Water Treatment by Liquid-Phase Discharge Plasma Synergistic With UVC
- 12 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 54  (2) , 560-568
Research on Self-Triggered Half-Bridge Submicrosecond Pulse Generators
With the widespread application of all-solid-state high-voltage pulse generators in environmental management, biomedicine, material modification, and plasma research, there is a trend toward miniaturization, arbitrary polarity, and modularization. This article proposes a half-bridge submicrosecond Marx pulse generator topology based on self-triggered drive. The biggest feature of this topology structure is the combination of a self-triggered drive circuit and a special half-bridge circuit, which only requires two isolated signals to control the on/off of the positive polarity final stage discharge switch and the negative polarity first stage discharge switch, respectively, while the remaining discharge switches work step by step through the self-triggered drive circuit. This simplifies the design of the driving circuit in the Marx pulse generator. In addition, this special half-bridge circuit can accelerate the pulse trailing edge by controlling the signal of the charging switches. In this article, a six-stage self-triggered bipolar pulse generator was constructed. This topology can stably generate repetitive bipolar pulses on both resistive and resistive–capacitive loads, with an output voltage amplitude of $0\sim 4.5$ kV, a pulsewidth of $0.3\sim 2~\mu $ s, a frequency of $0\sim 5$ kHz, and the interval time between positive and negative pulses can be flexibly adjusted. This pulse source is compact in structure and flexible in parameters, making it suitable for discharge application scenarios.
- 12 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 54  (2) , 560-568
Research on Self-Triggered Half-Bridge Submicrosecond Pulse Generators
With the widespread application of all-solid-state high-voltage pulse generators in environmental management, biomedicine, material modification, and plasma research, there is a trend toward miniaturization, arbitrary polarity, and modularization. This article proposes a half-bridge submicrosecond Marx pulse generator topology based on self-triggered drive. The biggest feature of this topology structure is the combination of a self-triggered drive circuit and a special half-bridge circuit, which only requires two isolated signals to control the on/off of the positive polarity final stage discharge switch and the negative polarity first stage discharge switch, respectively, while the remaining discharge switches work step by step through the self-triggered drive circuit. This simplifies the design of the driving circuit in the Marx pulse generator. In addition, this special half-bridge circuit can accelerate the pulse trailing edge by controlling the signal of the charging switches. In this article, a six-stage self-triggered bipolar pulse generator was constructed. This topology can stably generate repetitive bipolar pulses on both resistive and resistive–capacitive loads, with an output voltage amplitude of $0\sim 4.5$ kV, a pulsewidth of $0.3\sim 2~\mu $ s, a frequency of $0\sim 5$ kHz, and the interval time between positive and negative pulses can be flexibly adjusted. This pulse source is compact in structure and flexible in parameters, making it suitable for discharge application scenarios.
- 8 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53  (9) , 2292-2301
Research on Inductive Energy Storage Bipolar Pulse Current Generator
Bipolar pulse current sources are demonstrating superior performance in an increasing number of applications. This article proposes a novel topology for a bipolar pulsed current generator based on inductive energy storage. The system adopts a modular structure, with each module comprising positive and negative sections, and each polarity contains three switches, two diodes, and one inductor. The inductor is charged in series and discharges to the load in parallel, allowing the stored energy to be superimposed onto the load in the form of current. A prototype with five positive and five negative stages was developed, achieving an output current range of 0 to$\pm ~40$ A at a charging voltage of 25 V. Under a 1-$\Omega $ resistive load, the system demonstrates a maximum pulsewidth of$5~\mu $ s, a minimum rise and fall time of 100 ns, and stable operation at a repetition frequency of 200 Hz. In addition, by adjusting the timing signals, it is possible to achieve multiparameter adjustable pulse current outputs, including different polarities, pulse widths, and intervals between positive and negative pulses. Finally, by analyzing the power consumption of each operational process in the system, the energy efficiency of the system is calculated.- 8 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53  (9) , 2292-2301
Research on Inductive Energy Storage Bipolar Pulse Current Generator
Bipolar pulse current sources are demonstrating superior performance in an increasing number of applications. This article proposes a novel topology for a bipolar pulsed current generator based on inductive energy storage. The system adopts a modular structure, with each module comprising positive and negative sections, and each polarity contains three switches, two diodes, and one inductor. The inductor is charged in series and discharges to the load in parallel, allowing the stored energy to be superimposed onto the load in the form of current. A prototype with five positive and five negative stages was developed, achieving an output current range of 0 to$\pm ~40$ A at a charging voltage of 25 V. Under a 1-$\Omega $ resistive load, the system demonstrates a maximum pulsewidth of$5~\mu $ s, a minimum rise and fall time of 100 ns, and stable operation at a repetition frequency of 200 Hz. In addition, by adjusting the timing signals, it is possible to achieve multiparameter adjustable pulse current outputs, including different polarities, pulse widths, and intervals between positive and negative pulses. Finally, by analyzing the power consumption of each operational process in the system, the energy efficiency of the system is calculated.- 9 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53  (6) , 1250-1257
Research of High-Voltage Pulse Generator Based on Marx Circuit and Pulse Transformer
This article proposes the use of an all-solid-state Marx generator to drive a pulse transformer to output positive high-voltage pulses, reducing the stages of Marx generator and the insulation requirements, and improving the system reliability. The freewheeling circuit is designed in the Marx main circuit to avoid the saturation of transformer core so that it can work at the repetition frequency. At the same time, the charge on the capacitor load has a discharge circuit to reduce the pulse stretching. To verify the proposed scheme, a prototype is developed in this article. The Marx generator has 28 stages, which can output a 20-kV high-voltage pulse, pulse transformer with a ratio of 1:3. The experimental results show that when driving a 10-pF capacitive load, the proposed pulse power supply can output high-voltage pulses in a near-rectangular shape with an amplitude of 45 kV, a pulsewidth of $1~\mu $ s, a frequency of 300 Hz, a rise time of 240 ns, and a fall time of 500 ns. This article also investigates the basis for the selection of the modulating resistor and the efficiency of this pulse power supply.
- 9 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53  (6) , 1250-1257
Research of High-Voltage Pulse Generator Based on Marx Circuit and Pulse Transformer
This article proposes the use of an all-solid-state Marx generator to drive a pulse transformer to output positive high-voltage pulses, reducing the stages of Marx generator and the insulation requirements, and improving the system reliability. The freewheeling circuit is designed in the Marx main circuit to avoid the saturation of transformer core so that it can work at the repetition frequency. At the same time, the charge on the capacitor load has a discharge circuit to reduce the pulse stretching. To verify the proposed scheme, a prototype is developed in this article. The Marx generator has 28 stages, which can output a 20-kV high-voltage pulse, pulse transformer with a ratio of 1:3. The experimental results show that when driving a 10-pF capacitive load, the proposed pulse power supply can output high-voltage pulses in a near-rectangular shape with an amplitude of 45 kV, a pulsewidth of $1~\mu $ s, a frequency of 300 Hz, a rise time of 240 ns, and a fall time of 500 ns. This article also investigates the basis for the selection of the modulating resistor and the efficiency of this pulse power supply.
- 15 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53  (5) , 988-995
Research on Pulse Power Supply Based on High-Gain Boost Circuit
With the continuous development of pulse power technology in fields such as biomedicine, there is an increasing demand for miniaturization of pulse power supplies. This article proposes a portable pulse power supply based on a high-gain boost circuit powered by lithium batteries. It significantly provides the gain of the boost circuit through the combination of inductance and capacitance, while reducing the turn ratio of the pulse transformer, minimizing the leakage inductance and volume of the transformer. The prototype built in this article can achieve a voltage output of 05 kV, and its frequency and pulsewidth can be continuously adjusted. The size of the main circuit is only $16\times 10\times 8$ cm. It can work normally and stably under both resistive loads and dielectric barrier discharge (DBD) loads. Compared with the pulse generator of a traditional boost circuit, the efficiency is improved by about 10%. The results show that compared with traditional pulse power supplies, the pulse generator based on the high-gain boost proposed in this article has significant advantages in portability and efficiency.
- 15 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53  (5) , 988-995
Research on Pulse Power Supply Based on High-Gain Boost Circuit
With the continuous development of pulse power technology in fields such as biomedicine, there is an increasing demand for miniaturization of pulse power supplies. This article proposes a portable pulse power supply based on a high-gain boost circuit powered by lithium batteries. It significantly provides the gain of the boost circuit through the combination of inductance and capacitance, while reducing the turn ratio of the pulse transformer, minimizing the leakage inductance and volume of the transformer. The prototype built in this article can achieve a voltage output of 05 kV, and its frequency and pulsewidth can be continuously adjusted. The size of the main circuit is only $16\times 10\times 8$ cm. It can work normally and stably under both resistive loads and dielectric barrier discharge (DBD) loads. Compared with the pulse generator of a traditional boost circuit, the efficiency is improved by about 10%. The results show that compared with traditional pulse power supplies, the pulse generator based on the high-gain boost proposed in this article has significant advantages in portability and efficiency.
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53  (3) , 389-397
The Spatial Resolution Effect of N2/O2 on Atmospheric Pressure Ar Plasma Jet
The atmospheric pressure low-temperature plasma jet (APPJ) can generate a wide variety of excited and active particles, with broad application prospects. Due to the strong spatiotemporal distribution characteristics of particles, the physical and chemical properties of plasma jets can be adjusted by changing the type and ratio of working gas, which is crucial for improving jet treatment efficiency and achieving specific treatment effects. This article innovatively analyzes the variations in the spatial distribution, intensity distribution, and activation region distribution of short-lived active substances that are crucial in the application of plasma jets under different gas backgrounds. Under the context of multiple variables, the physical characteristics of the plasma jets are comprehensively analyzed. The results show that the addition of N2 and O2 will weaken the discharge current and power, especially oxygen. After doping with 1% nitrogen, the jet length remains basically unchanged, but after doping with 1% oxygen, the jet length sharply decreases. Most active substances are concentrated at the nozzle of the jet pipe. The activation region of $\mathrm{OH}(\mathrm{A}^{2}\Sigma^{{+}}\to\mathrm{X}^{2}{\Pi})$ is significantly lower than that of $\mathrm{N}_{{2}}(\mathrm{C}^{3}\Pi_{\mathrm{u}}\to\mathrm{B}^{{3}}\Pi_{\mathrm{g}} )$. As the N2 content increases from 0% to 1%, the activation region of $\mathrm{OH}(\mathrm{A}^{{2}}\Sigma^{+}\to\mathrm{X}^{{2}}\Pi)$ decays from 17 to 12 mm and the activation region of $\mathrm{N}_{{2}}(\mathrm{C}^{{3}}{{\Pi}}_{\mathrm{u}}\to\mathrm{B}^{{3}}\Pi_{\mathrm{g}} )$ remains unchanged, but the intensity of $\mathrm{N}_{{2}}(\mathrm{C}^{{3}}\Pi_{\mathrm{u}}\to\mathrm{B}^{3}\Pi_{\mathrm{g}} )$ spectral line rises rapidly. As the O2 content increases from 0% to 0.1%, the activation region of $\mathrm{OH}(\mathrm{A}^{{2}}{{\Sigma}}^{{+}}\to\mathrm{X}^{{2}}{\Pi )}$ has decayed below 10 mm. The intensity of $\mathrm{N}_{{2}}(\mathrm{C}^{{3}}{{\Pi}}_{\mathrm{u}}\to\mathrm{B}^{{3}}\Pi_{\mathrm{g}} )$ spectral extremely reduced by 48%. The increase in N2 content will lead to an increase in vibration and rotation temperature, while O2 is the opposite. From the axial spatial distribution, the vibrational temperature does not change much, but the rotational temperature decreases with increasing distance from the electrodes and eventually reaches equilibrium with the room temperature of 295 K.
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53  (3) , 389-397
The Spatial Resolution Effect of N2/O2 on Atmospheric Pressure Ar Plasma Jet
The atmospheric pressure low-temperature plasma jet (APPJ) can generate a wide variety of excited and active particles, with broad application prospects. Due to the strong spatiotemporal distribution characteristics of particles, the physical and chemical properties of plasma jets can be adjusted by changing the type and ratio of working gas, which is crucial for improving jet treatment efficiency and achieving specific treatment effects. This article innovatively analyzes the variations in the spatial distribution, intensity distribution, and activation region distribution of short-lived active substances that are crucial in the application of plasma jets under different gas backgrounds. Under the context of multiple variables, the physical characteristics of the plasma jets are comprehensively analyzed. The results show that the addition of N2 and O2 will weaken the discharge current and power, especially oxygen. After doping with 1% nitrogen, the jet length remains basically unchanged, but after doping with 1% oxygen, the jet length sharply decreases. Most active substances are concentrated at the nozzle of the jet pipe. The activation region of $\mathrm{OH}(\mathrm{A}^{2}\Sigma^{{+}}\to\mathrm{X}^{2}{\Pi})$ is significantly lower than that of $\mathrm{N}_{{2}}(\mathrm{C}^{3}\Pi_{\mathrm{u}}\to\mathrm{B}^{{3}}\Pi_{\mathrm{g}} )$. As the N2 content increases from 0% to 1%, the activation region of $\mathrm{OH}(\mathrm{A}^{{2}}\Sigma^{+}\to\mathrm{X}^{{2}}\Pi)$ decays from 17 to 12 mm and the activation region of $\mathrm{N}_{{2}}(\mathrm{C}^{{3}}{{\Pi}}_{\mathrm{u}}\to\mathrm{B}^{{3}}\Pi_{\mathrm{g}} )$ remains unchanged, but the intensity of $\mathrm{N}_{{2}}(\mathrm{C}^{{3}}\Pi_{\mathrm{u}}\to\mathrm{B}^{3}\Pi_{\mathrm{g}} )$ spectral line rises rapidly. As the O2 content increases from 0% to 0.1%, the activation region of $\mathrm{OH}(\mathrm{A}^{{2}}{{\Sigma}}^{{+}}\to\mathrm{X}^{{2}}{\Pi )}$ has decayed below 10 mm. The intensity of $\mathrm{N}_{{2}}(\mathrm{C}^{{3}}{{\Pi}}_{\mathrm{u}}\to\mathrm{B}^{{3}}\Pi_{\mathrm{g}} )$ spectral extremely reduced by 48%. The increase in N2 content will lead to an increase in vibration and rotation temperature, while O2 is the opposite. From the axial spatial distribution, the vibrational temperature does not change much, but the rotational temperature decreases with increasing distance from the electrodes and eventually reaches equilibrium with the room temperature of 295 K.
- 30 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53  (4) , 487-496
A Compact Solid-State Bipolar Pulse Adder for Dielectric Barrier Discharges
To excite atmospheric pressure dielectric barrier discharges (DBDs) and to regulate the low-temperature plasma intensity, a compact all-solid-state bipolar pulse adder with nanosecond edges is developed. It uses two MOSFETs with their source terminals shorted to form a special half-bridge circuit, and each stage includes two such half-bridge circuits and one capacitor. One bipolar signal applied to both gates of these two MOSFETs can turn them on alternately. Combined with a magnetic isolated driver with primary windings in series, one bipolar signal from the primary side can drive many charging and discharging switches, which considerably reduces the number of required components in the drive circuits. A prototype was constructed and the test results were demonstrated. The designed bipolar pulse adder can generate repetitive bipolar square wave pulses with voltage up to $\pm$ 8 kV, a pulsewidth of 0.3 $\sim$ 500 $\mu$ s, and pulse edges of around 45 ns. The size of the power circuit in this bipolar pulse adder is 14.5 $\times$ 5 $\times$ 7 cm, which is very compact. All the voltage amplitude, pulsewidth, dead time, and repetition frequency of the bipolar pulses can be adjusted continuously. They all affect the plasma intensity of DBDs. Experiments show that increasing the voltage amplitude and repetition frequency can multiply the intensity of plasma. Adjusting pulsewidth and dead time can affect the number of remanent charges and be used as a precise adjustment of the intensity of particles. The power efficiency of 69.7% was realized.
- 30 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53  (4) , 487-496
A Compact Solid-State Bipolar Pulse Adder for Dielectric Barrier Discharges
To excite atmospheric pressure dielectric barrier discharges (DBDs) and to regulate the low-temperature plasma intensity, a compact all-solid-state bipolar pulse adder with nanosecond edges is developed. It uses two MOSFETs with their source terminals shorted to form a special half-bridge circuit, and each stage includes two such half-bridge circuits and one capacitor. One bipolar signal applied to both gates of these two MOSFETs can turn them on alternately. Combined with a magnetic isolated driver with primary windings in series, one bipolar signal from the primary side can drive many charging and discharging switches, which considerably reduces the number of required components in the drive circuits. A prototype was constructed and the test results were demonstrated. The designed bipolar pulse adder can generate repetitive bipolar square wave pulses with voltage up to $\pm$ 8 kV, a pulsewidth of 0.3 $\sim$ 500 $\mu$ s, and pulse edges of around 45 ns. The size of the power circuit in this bipolar pulse adder is 14.5 $\times$ 5 $\times$ 7 cm, which is very compact. All the voltage amplitude, pulsewidth, dead time, and repetition frequency of the bipolar pulses can be adjusted continuously. They all affect the plasma intensity of DBDs. Experiments show that increasing the voltage amplitude and repetition frequency can multiply the intensity of plasma. Adjusting pulsewidth and dead time can affect the number of remanent charges and be used as a precise adjustment of the intensity of particles. The power efficiency of 69.7% was realized.
- 17 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52  (11) , 5358-5365
Research on the Effect of Pulsed Discharge Plasma With g-C₃N₄ for Water Treatment
Plasma-assisted catalysts for water treatment have attracted increasing attention due to their high energy efficiency. In this article, graphite phase carbon nitride (g-C $_{{3}}$ N $_{4}$ ) is used as a catalyst for synergistic plasma discharge in water treatment. The discharge characteristics of g-C $_{{3}}$ N $_{{4}}$ , the generation of H $_{2}$ O $_{2}$ , and the changes in the physical and chemical properties of the catalyst before and after discharge have been studied. The results showed that after adding the catalyst, the current and power were slightly lower than those without the catalyst at the same voltage. However, the amount of H $_{2}$ O $_{2}$ produced is about twice that of the original under the same processing time. Furthermore, the physical properties of the catalyst showed a significant increase in the relative surface area of g-C $_{3}$ N $_{4}$ after discharge, while the pore volume of the catalyst also increased. Regarding chemical properties, the oxygen content of g-C $_{3}$ N $_{4}$ continues to increase after discharge, and the ratio of carbon and nitrogen elements also continues to increase. These changes suggest that the plasma generated by the discharge enhanced the catalytic effect of the g-C $_{3}$ N $_{4}$ . Finally, the treatment of the target pollutant shows that the addition of g-C $_{3}$ N $_{4}$ resulted in significantly higher degradation efficiency and energy efficiency compared to the absence of g-C $_{3}$ N $_{4}$ .
- 17 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52  (11) , 5358-5365
Research on the Effect of Pulsed Discharge Plasma With g-C₃N₄ for Water Treatment
Plasma-assisted catalysts for water treatment have attracted increasing attention due to their high energy efficiency. In this article, graphite phase carbon nitride (g-C $_{{3}}$ N $_{4}$ ) is used as a catalyst for synergistic plasma discharge in water treatment. The discharge characteristics of g-C $_{{3}}$ N $_{{4}}$ , the generation of H $_{2}$ O $_{2}$ , and the changes in the physical and chemical properties of the catalyst before and after discharge have been studied. The results showed that after adding the catalyst, the current and power were slightly lower than those without the catalyst at the same voltage. However, the amount of H $_{2}$ O $_{2}$ produced is about twice that of the original under the same processing time. Furthermore, the physical properties of the catalyst showed a significant increase in the relative surface area of g-C $_{3}$ N $_{4}$ after discharge, while the pore volume of the catalyst also increased. Regarding chemical properties, the oxygen content of g-C $_{3}$ N $_{4}$ continues to increase after discharge, and the ratio of carbon and nitrogen elements also continues to increase. These changes suggest that the plasma generated by the discharge enhanced the catalytic effect of the g-C $_{3}$ N $_{4}$ . Finally, the treatment of the target pollutant shows that the addition of g-C $_{3}$ N $_{4}$ resulted in significantly higher degradation efficiency and energy efficiency compared to the absence of g-C $_{3}$ N $_{4}$ .
- 25 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52  (8) , 3218-3227
A Bipolar Pulse Generator Without H-Bridge Controlled by a Magnetically Isolated Driver
Based on the widespread application of pulsed power technology in food safety and medicine, this article develops a bipolar pulsed power generator without an H-bridge controlled by a magnetically isolated driver. The main circuit of the developed pulse power supply adopts the positive-and negative-polarity Marx circuit cascade, which can output bipolar high-voltage pulses without any auxiliary circuits. Moreover, the main circuit has added anti-straight-through diodes. These diodes can truncate the short-circuit current generated when a straight-through short-circuit fault occurs in the circuit, safeguarding the switches and enhancing the power supply stability. In addition, the switching drive scheme uses a series core magnetic ring and the secondary-side windings in anti-parallel, requiring only two drive signals to achieve separate control of the four sets of switches in the bipolar pulse generator. According to the proposed main circuit structure and driving scheme, the simulation of the main circuit and driving circuit are conducted to lay a theoretical foundation for developing the prototype. Subsequently, a 20-stage prototype of a bipolar pulse generator is created. The experimental results show that the system can generate bipolar high-voltage pulses with a voltage amplitude of 0 $\sim$ $\pm$ 15 kV, a pulsewidth of 1–10 $\mu $ s, and a repetition frequency of 0–1 kHz. The interval time between positive and negative pulses can be flexibly adjusted.
- 25 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52  (8) , 3218-3227
A Bipolar Pulse Generator Without H-Bridge Controlled by a Magnetically Isolated Driver
Based on the widespread application of pulsed power technology in food safety and medicine, this article develops a bipolar pulsed power generator without an H-bridge controlled by a magnetically isolated driver. The main circuit of the developed pulse power supply adopts the positive-and negative-polarity Marx circuit cascade, which can output bipolar high-voltage pulses without any auxiliary circuits. Moreover, the main circuit has added anti-straight-through diodes. These diodes can truncate the short-circuit current generated when a straight-through short-circuit fault occurs in the circuit, safeguarding the switches and enhancing the power supply stability. In addition, the switching drive scheme uses a series core magnetic ring and the secondary-side windings in anti-parallel, requiring only two drive signals to achieve separate control of the four sets of switches in the bipolar pulse generator. According to the proposed main circuit structure and driving scheme, the simulation of the main circuit and driving circuit are conducted to lay a theoretical foundation for developing the prototype. Subsequently, a 20-stage prototype of a bipolar pulse generator is created. The experimental results show that the system can generate bipolar high-voltage pulses with a voltage amplitude of 0 $\sim$ $\pm$ 15 kV, a pulsewidth of 1–10 $\mu $ s, and a repetition frequency of 0–1 kHz. The interval time between positive and negative pulses can be flexibly adjusted.