Fidel Gamboa
Research Subjects
Fidel Gamboa has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Andres Ivan Oliva
Facultad de Ingeniería Universidad Autónoma de Yucatán Mérida Yucatán Mexico
4 shared publications - Francis Aviles
Materials Department, Centro de Investigacin Cientfica de Yucatn, Mrida, Mexico
3 shared publications - Israel Perez
Department of Physics and Engineering Physics University of Saskatchewan Saskatoon SK Canada
3 shared publications - José Luis Enríquez-Carrejo
Departamento de Física y Matemáticas, Instituto de Ingeniería y Tecnología, Universidad Autónoma de Ciudad Juárez, Juárez, Chihuahua, México
3 shared publications - Israel Perez
Applied Physics Department, Cinvestav Unidad Mérida, Km 6 Ant., Carretera a Progreso, A.P. 73, C.P. 97310, Mérida, Yucatán, Mexico
2 shared publications - Juan Carlos Mixteco-Sánchez
Natural and Exact Sciences Department, University of Guadalajara, Ameca 46600, Mexico
2 shared publications
Latest Publications
- 1 January 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (2) , 025320
Design and implementation of a controlled heater system for the investigation of thermoresistive properties of polymer nanocomposites
The design and implementation of a controlled technique for heating polymer nanocomposites is here presented. The device consists on a heating system controlled by a program developed and implemented in LabVIEW, which is able to precisely increase the temperature within a range of 25 °C–100 °C. The temperatures of both the heating system and the nanocomposite sample were simultaneously captured and serve as inputs to properly control the energy supply to the system. The experimental setup shows excellent uniformity, reproducibility and control of the sample temperature, being of paramount importance for the evaluation of the thermoresistive properties of the nanocomposites. As a proof of concept, the exploration of thermoresistive response of polymer nanocomposites filled with graphene sheets was carried out. Preliminary registers of thermal coefficients of resistance in the order of values reported for similar materials demonstrate the effectiveness of the implemented setup. The presented system adequately performed as an accessible and low-cost option to explore thermoresistive properties of polymeric nanocomposite samples in film geometry.
- 1 January 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (2) , 025320
Design and implementation of a controlled heater system for the investigation of thermoresistive properties of polymer nanocomposites
The design and implementation of a controlled technique for heating polymer nanocomposites is here presented. The device consists on a heating system controlled by a program developed and implemented in LabVIEW, which is able to precisely increase the temperature within a range of 25 °C–100 °C. The temperatures of both the heating system and the nanocomposite sample were simultaneously captured and serve as inputs to properly control the energy supply to the system. The experimental setup shows excellent uniformity, reproducibility and control of the sample temperature, being of paramount importance for the evaluation of the thermoresistive properties of the nanocomposites. As a proof of concept, the exploration of thermoresistive response of polymer nanocomposites filled with graphene sheets was carried out. Preliminary registers of thermal coefficients of resistance in the order of values reported for similar materials demonstrate the effectiveness of the implemented setup. The presented system adequately performed as an accessible and low-cost option to explore thermoresistive properties of polymeric nanocomposite samples in film geometry.
- Open Access
- 31 August 2025
- Published by Universidad Nacional Autonoma de Mexico in Journal of Applied Research and Technology
- Vol. 23 (4) , 362-370
Assessing the effect of LiClO4 electrolyte on the electrochemical properties of indium tin oxide thin films
In this research, we used a combination of experimental techniques to shed some light on the effect of lithium perchlorate (LiClO(4)) on the electrochemical and physical properties of indium tin oxide (ITO) films. For this, we studied the effect of ITO films immersed in a LiClO(4)/PC+EC solution. Chronoamperometry, along with transmissivity measurements, shows that ITO undergoes optical changes as a function of voltage changes. However, as the number of cycles increases, the transmissivity decreases significantly due to ITO degradation. Cyclic voltammetry reveals the presence of reduction and oxidation processes, suggesting ITO reduction and possible ion trapping. X-ray diffraction does not show compelling signs of lithium insertion or the presence of other phases. Finally, X-ray photoelectron spectroscopy is used to evaluate the oxidation states and chemical bonding. The analysis reveals the presence of indium oxide, suggesting that the surface is mainly ITO, in agreement with XRD studies.
- 31 August 2025
- Published by Universidad Nacional Autonoma de Mexico in Journal of Applied Research and Technology
- Vol. 23 (4) , 362-370
Open AccessAssessing the effect of LiClO4 electrolyte on the electrochemical properties of indium tin oxide thin films
In this research, we used a combination of experimental techniques to shed some light on the effect of lithium perchlorate (LiClO(4)) on the electrochemical and physical properties of indium tin oxide (ITO) films. For this, we studied the effect of ITO films immersed in a LiClO(4)/PC+EC solution. Chronoamperometry, along with transmissivity measurements, shows that ITO undergoes optical changes as a function of voltage changes. However, as the number of cycles increases, the transmissivity decreases significantly due to ITO degradation. Cyclic voltammetry reveals the presence of reduction and oxidation processes, suggesting ITO reduction and possible ion trapping. X-ray diffraction does not show compelling signs of lithium insertion or the presence of other phases. Finally, X-ray photoelectron spectroscopy is used to evaluate the oxidation states and chemical bonding. The analysis reveals the presence of indium oxide, suggesting that the surface is mainly ITO, in agreement with XRD studies.
- 1 March 2022
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 156 (9) , 094701
Role of lithium intercalation in fluorine-doped tin oxide thin films: Ab initio calculations and experiment
Using a combination of experimental techniques and density functional theory (DFT) calculations, the influence of lithium insertion on the electronic and electrochemical properties of fluorine-doped SnO2 (FTO) is assessed. For this purpose, we investigate the electrochromic behavior of a commercial FTO electrode embedded in a solution of lithium perclorate (LiClO4). The electrochromic properties are evaluated by UV–vis spectroscopy, cyclic voltammetry, and chronoamperometry. These tests show that FTO exhibits electrochromism with a respectable coloration efficiency (η = 47.9 cm2/C at 637 nm). DFT study indicates that lithium remains ionized in the lattice, raising the Fermi level about 0.7 eV deep into the conduction band. X-ray photoelectron spectroscopy (XPS) is used to study chemical bonding and oxidation states. XPS analysis of the Sn 3d core levels reveals that lithium insertion in FTO induces a shift of 350 meV in the Sn 3d states, suggesting that lithium is incorporated into the SnO2 lattice.
- 1 March 2022
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 156 (9) , 094701
Role of lithium intercalation in fluorine-doped tin oxide thin films: Ab initio calculations and experiment
Using a combination of experimental techniques and density functional theory (DFT) calculations, the influence of lithium insertion on the electronic and electrochemical properties of fluorine-doped SnO2 (FTO) is assessed. For this purpose, we investigate the electrochromic behavior of a commercial FTO electrode embedded in a solution of lithium perclorate (LiClO4). The electrochromic properties are evaluated by UV–vis spectroscopy, cyclic voltammetry, and chronoamperometry. These tests show that FTO exhibits electrochromism with a respectable coloration efficiency (η = 47.9 cm2/C at 637 nm). DFT study indicates that lithium remains ionized in the lattice, raising the Fermi level about 0.7 eV deep into the conduction band. X-ray photoelectron spectroscopy (XPS) is used to study chemical bonding and oxidation states. XPS analysis of the Sn 3d core levels reveals that lithium insertion in FTO induces a shift of 350 meV in the Sn 3d states, suggesting that lithium is incorporated into the SnO2 lattice.
- 30 September 2020
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 29 (11) , 115021
Electro-mechanical properties of thermoplastic polyurethane films and tubes modified by hybrid carbon nanostructures for pressure sensing
Electrical and piezoresistive properties of hybrid nanocomposite films and tubes made of a segmented aliphatic polyurethane modified with multilayer graphene sheets (MLGSs), multiwall carbon nanotubes (MWCNTs), and hybrid mixtures of both, were investigated. Hybrid nanocomposites were fabricated at a total weight concentration ( Φ T ) of 5 wt.%, with relative weight concentration of MLGSs with respect to MWCNTs ( Φ R ) of 25%, 50% and 75%. The electrical conductivity of these films is dominated by the MWCNT network, observing electrical MLGS-MWCNT collaborative effects only for Φ R = 25%. Dielectric impedance spectroscopy indicates that the nanocomposites display capacitive effects at frequencies higher than tens of Hz, which is explained by interfacial polarization. The burst pressure and circumferential stiffness of internally pressurized tubes fabricated from these films is slightly higher for tubes containing only MWCNTs. The strain fields in the pressurized tubes, determined by digital image correlation, showed localized strain gradients, and the piezoresistive response of the electro-conductive tubes was nonlinear. The highest pressure sensitivity factor (4.59 kPa −1 ) was obtained for hybrid nanocomposite tubes with Φ R = 25%.
- 30 September 2020
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 29 (11) , 115021
Electro-mechanical properties of thermoplastic polyurethane films and tubes modified by hybrid carbon nanostructures for pressure sensing
Electrical and piezoresistive properties of hybrid nanocomposite films and tubes made of a segmented aliphatic polyurethane modified with multilayer graphene sheets (MLGSs), multiwall carbon nanotubes (MWCNTs), and hybrid mixtures of both, were investigated. Hybrid nanocomposites were fabricated at a total weight concentration ( Φ T ) of 5 wt.%, with relative weight concentration of MLGSs with respect to MWCNTs ( Φ R ) of 25%, 50% and 75%. The electrical conductivity of these films is dominated by the MWCNT network, observing electrical MLGS-MWCNT collaborative effects only for Φ R = 25%. Dielectric impedance spectroscopy indicates that the nanocomposites display capacitive effects at frequencies higher than tens of Hz, which is explained by interfacial polarization. The burst pressure and circumferential stiffness of internally pressurized tubes fabricated from these films is slightly higher for tubes containing only MWCNTs. The strain fields in the pressurized tubes, determined by digital image correlation, showed localized strain gradients, and the piezoresistive response of the electro-conductive tubes was nonlinear. The highest pressure sensitivity factor (4.59 kPa −1 ) was obtained for hybrid nanocomposite tubes with Φ R = 25%.
- 1 October 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 54 (3) , 2205-2221
Electrophoretic deposition of carbon nanotubes onto glass fibers for self-sensing relaxation-induced piezoresistivity of monofilament composites
- 1 October 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 54 (3) , 2205-2221
Electrophoretic deposition of carbon nanotubes onto glass fibers for self-sensing relaxation-induced piezoresistivity of monofilament composites
- 1 July 2017
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 712, 303-310
Evidence for structural transition in crystalline tantalum pentoxide films grown by RF magnetron sputtering
- 1 July 2017
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 712, 303-310
Evidence for structural transition in crystalline tantalum pentoxide films grown by RF magnetron sputtering
- 15 February 2016
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 27 (4) , 045002
A vibrating reed apparatus to measure the natural frequency of multilayered thin films
An apparatus for measuring the natural frequency of sub-micrometric layered films in cantilever beam configuration is presented. The instrument comprises a specially designed test rig with a sample holder, an electronic excitation source, a vibration sensor and an automated software for the excitation and data recollection. The beam is excited by means of an air pulse and the oscillation amplitude of its free end is measured through a laser diode-photosensor arrangement. The instrument provides a very low uncertainty (~1 mHz, for frequencies of the order of tens Hz) for repeated sequential tests and the major source of uncertainty (~0.2 Hz, corresponding to a coefficient of variation of 0.18%) arises from the difficulty of placing the sample in an exactly identical location upon clamping. This high sensitivity renders the capability of measuring very small frequency shifts upon deposition of sub-micrometric films over thicker substrates. In order to assess the reliability of the apparatus, cantilever beams of 125 μm thick neat Kapton (substrate) and thin layered films of Au/Kapton and Al/Au/Kapton of 200–250 nm film thickness were fabricated and their natural frequency and damping factor were measured. Calculations of the natural frequency of such beams by finite element analysis further support the accuracy of the experimental measurements.
- 15 February 2016
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 27 (4) , 045002
A vibrating reed apparatus to measure the natural frequency of multilayered thin films
An apparatus for measuring the natural frequency of sub-micrometric layered films in cantilever beam configuration is presented. The instrument comprises a specially designed test rig with a sample holder, an electronic excitation source, a vibration sensor and an automated software for the excitation and data recollection. The beam is excited by means of an air pulse and the oscillation amplitude of its free end is measured through a laser diode-photosensor arrangement. The instrument provides a very low uncertainty (~1 mHz, for frequencies of the order of tens Hz) for repeated sequential tests and the major source of uncertainty (~0.2 Hz, corresponding to a coefficient of variation of 0.18%) arises from the difficulty of placing the sample in an exactly identical location upon clamping. This high sensitivity renders the capability of measuring very small frequency shifts upon deposition of sub-micrometric films over thicker substrates. In order to assess the reliability of the apparatus, cantilever beams of 125 μm thick neat Kapton (substrate) and thin layered films of Au/Kapton and Al/Au/Kapton of 200–250 nm film thickness were fabricated and their natural frequency and damping factor were measured. Calculations of the natural frequency of such beams by finite element analysis further support the accuracy of the experimental measurements.
- Open AccessIn situ comparison of the critical current density in $Y Ba_2 Cu_3 O_{7-δ}$ thin films measured by the screening technique under two criteriaIn this investigation we report the determination of the critical current density $J_c$ flowing in a $\mathrm{Y}\mathrm{Ba}_2\mathrm{Cu}_3\mathrm{O}_{7-\delta}$ superconducting thin film. Estimation of $J_c$ was carried out by an inductive technique, the so-called screening technique, in which both the imaginary part of the fundamental harmonic of susceptibility $\chi''_1$ and third harmonic voltage $V_3$ criteria were considered for the determination of the full penetration field. In order to verify the reliability of this technique under two criteria, we investigated the homogeneity of $J_c$ via transport measurements conducted on four microbridges patterned in the same film. Based on the transport method we found that both techniques yield similar results in the determination of $J_c$ for temperatures close to critical temperature $T_c$. However, at temperatures relatively far from $T_c$, the $V_3$ criterion showed a better agreement with the transport data. Furthermore, using both criteria, we propose a methodology to estimate in situ the coil factor associated with the $V_3$ criterion, avoiding in this way the need of implementing an additional technique.Open AccessIn situ comparison of the critical current density in $Y Ba_2 Cu_3 O_{7-δ}$ thin films measured by the screening technique under two criteriaIn this investigation we report the determination of the critical current density $J_c$ flowing in a $\mathrm{Y}\mathrm{Ba}_2\mathrm{Cu}_3\mathrm{O}_{7-\delta}$ superconducting thin film. Estimation of $J_c$ was carried out by an inductive technique, the so-called screening technique, in which both the imaginary part of the fundamental harmonic of susceptibility $\chi''_1$ and third harmonic voltage $V_3$ criteria were considered for the determination of the full penetration field. In order to verify the reliability of this technique under two criteria, we investigated the homogeneity of $J_c$ via transport measurements conducted on four microbridges patterned in the same film. Based on the transport method we found that both techniques yield similar results in the determination of $J_c$ for temperatures close to critical temperature $T_c$. However, at temperatures relatively far from $T_c$, the $V_3$ criterion showed a better agreement with the transport data. Furthermore, using both criteria, we propose a methodology to estimate in situ the coil factor associated with the $V_3$ criterion, avoiding in this way the need of implementing an additional technique.
- 14 March 2012
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 23 (4)
Vibration modeling and testing of bilayer beams for determination of film elastic modulus
- 14 March 2012
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 23 (4)
Vibration modeling and testing of bilayer beams for determination of film elastic modulus
- 8 October 2010
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 470 (22) , 2061-2066
Study of higher-order harmonics of complex ac susceptibility in YBa2Cu3O7−δ thin films by the mutual inductive method
- 8 October 2010
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 470 (22) , 2061-2066
Study of higher-order harmonics of complex ac susceptibility in YBa2Cu3O7−δ thin films by the mutual inductive method