Michael A. Bell
Research Subjects
Michael A. Bell has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
James C. Weaver
John A. Paulson School of Engineering and Applied Sciences, Science and Engineering Center, Allston, Massachusetts, USA
4 shared publications- Robert J. Wood
Harvard University
3 shared publications Robert J. Wood
John A. Paulson School of Engineering and Applied Sciences, Science and Engineering Center, Allston, Massachusetts, USA
2 shared publications- Benjamin Gorissen
Department of Mechanical Engineering KU Leuven 3001 Leuven Belgium
1 shared publication Carmel Majidi
Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh, PA, USA
1 shared publication- Derek A. Paley
University of Maryland
1 shared publication
Latest Publications
- 31 December 2021
- Published by SAGE Publications in Soft Robotics
- Vol. 9 (5) , 991-1000
An Ambidextrous STarfish-Inspired Exploration and Reconnaissance Robot (The ASTER-bot)
As more roboticists are turning to Nature for design inspiration, it is becoming increasingly apparent that multisystem-level investigations of biological processes can frequently lead to unexpected advances in the development of experimental research platforms. Inspired by these efforts, we present here a holistic approach to developing an autonomous starfish-inspired soft robot that embodies a number of key design, fabrication, and actuation principles. These key concepts include integrated and sequentially deployable magnetic tube feet for site-specific and reversible substrate attachment, individually addressable flexible arms, and highly efficient and self-contained fluidic engines. These individual features offer a level of synergistic motion control not previously seen in other starfish-inspired robots. For example, our bistable dome-like tube feet are capable of achieving high adhesion forces to ferrous surfaces and low removal forces. These tube feet are further integrated with a fluidic engine to drive the entire arm while maintaining the ability to accurately control the arm position with a 270° range of motion. Furthermore, the arm and fluidic engine are modular, allowing each of the five arms to be replaced in seconds or enabling the exploration of a variety of limb geometries. Through the incorporation of these different design elements, the ASTER-bot (named for its star-like body plan) is capable of locomotion on ferrous surfaces, above and below water, and on nonplanar surfaces. This article further describes the design, fabrication, and integration strategies and characterizes the energetic and locomotory performance of this pentaradial robotic prototype.
- 31 December 2021
- Published by SAGE Publications in Soft Robotics
- Vol. 9 (5) , 991-1000
An Ambidextrous STarfish-Inspired Exploration and Reconnaissance Robot (The ASTER-bot)
As more roboticists are turning to Nature for design inspiration, it is becoming increasingly apparent that multisystem-level investigations of biological processes can frequently lead to unexpected advances in the development of experimental research platforms. Inspired by these efforts, we present here a holistic approach to developing an autonomous starfish-inspired soft robot that embodies a number of key design, fabrication, and actuation principles. These key concepts include integrated and sequentially deployable magnetic tube feet for site-specific and reversible substrate attachment, individually addressable flexible arms, and highly efficient and self-contained fluidic engines. These individual features offer a level of synergistic motion control not previously seen in other starfish-inspired robots. For example, our bistable dome-like tube feet are capable of achieving high adhesion forces to ferrous surfaces and low removal forces. These tube feet are further integrated with a fluidic engine to drive the entire arm while maintaining the ability to accurately control the arm position with a 270° range of motion. Furthermore, the arm and fluidic engine are modular, allowing each of the five arms to be replaced in seconds or enabling the exploration of a variety of limb geometries. Through the incorporation of these different design elements, the ASTER-bot (named for its star-like body plan) is capable of locomotion on ferrous surfaces, above and below water, and on nonplanar surfaces. This article further describes the design, fabrication, and integration strategies and characterizes the energetic and locomotory performance of this pentaradial robotic prototype.
- 8 October 2021
- Published by Wiley in Advanced Materials Technologies
- Vol. 7 (1) , 2100605
Injection Molding of Soft Robots
To date, injection molding has not been a practical manufacturing method for soft robots due to machine costs, large volumes of liquid silicones required, and the inability to change materials quickly between shots. Injection molds are typically machined from metals to allow for high pressure and clamping forces, which further limits the ability to rapidly prototype soft robots when molds could cost thousands of dollars. To circumvent these issues, a low‐cost injection molding system and process are pioneered. In this article, the apparatus, design process, economics, and workflow are described using standard stereolithography and polyjet 3D printers to rapidly iterate on soft robot designs. The mold design process is further detailed to allow for proper material flow, clamping, alignment, and rapid curing times. Static mixing nozzle efficacy is characterized with common silicone materials compared to manual mixing and centrifugal planetary mixing. Lastly, a number of applications that could only be achieved through injection molding due to geometry, embedded components, or cure times are presented.
- 8 October 2021
- Published by Wiley in Advanced Materials Technologies
- Vol. 7 (1) , 2100605
Injection Molding of Soft Robots
To date, injection molding has not been a practical manufacturing method for soft robots due to machine costs, large volumes of liquid silicones required, and the inability to change materials quickly between shots. Injection molds are typically machined from metals to allow for high pressure and clamping forces, which further limits the ability to rapidly prototype soft robots when molds could cost thousands of dollars. To circumvent these issues, a low‐cost injection molding system and process are pioneered. In this article, the apparatus, design process, economics, and workflow are described using standard stereolithography and polyjet 3D printers to rapidly iterate on soft robot designs. The mold design process is further detailed to allow for proper material flow, clamping, alignment, and rapid curing times. Static mixing nozzle efficacy is characterized with common silicone materials compared to manual mixing and centrifugal planetary mixing. Lastly, a number of applications that could only be achieved through injection molding due to geometry, embedded components, or cure times are presented.
- Open Access
- 24 September 2021
- Published by Wiley in Advanced Intelligent Systems
- Vol. 4 (1) , 2100094
A Modular and Self‐Contained Fluidic Engine for Soft Actuators
Fluidic actuation in soft robots traditionally requires a complex assemblage of pumps, regulators, valves, and sensors, often resulting in large and bulky support systems. This added bulk can often hinder a robot's ability to be untethered, perform complex tasks, or bring challenges when it comes to maintenance or upgradeability. To address these limitations, herein, a simple and highly modular bidirectional soft robotic appendage is presented that integrates the pump, flow lines, and actuator into a compact, closed hydraulic system, which is driven by an integrated stepper motor, allowing for positional control and fast response times. The actuator can also be swapped in under five seconds, allowing for rapid reconfiguration. Each component has been thoroughly characterized to determine an overall electrical to mechanical efficiency of the system, and from these calculations, it is demonstrated that the actuator utilizes only 1/15th the required energy to achieve a specific bending angle, and is four‐fold more power‐efficient than similar‐sized soft actuators and pumping systems reported in the literature. The integrated actuator and fluidic engine construct presented here thus represents a major departure from previous soft actuator control platforms in that everything is simplified down to a single self‐contained unit, demonstrating unparalleled versatility and modularity.
- 24 September 2021
- Published by Wiley in Advanced Intelligent Systems
- Vol. 4 (1) , 2100094
Open AccessA Modular and Self‐Contained Fluidic Engine for Soft Actuators
Fluidic actuation in soft robots traditionally requires a complex assemblage of pumps, regulators, valves, and sensors, often resulting in large and bulky support systems. This added bulk can often hinder a robot's ability to be untethered, perform complex tasks, or bring challenges when it comes to maintenance or upgradeability. To address these limitations, herein, a simple and highly modular bidirectional soft robotic appendage is presented that integrates the pump, flow lines, and actuator into a compact, closed hydraulic system, which is driven by an integrated stepper motor, allowing for positional control and fast response times. The actuator can also be swapped in under five seconds, allowing for rapid reconfiguration. Each component has been thoroughly characterized to determine an overall electrical to mechanical efficiency of the system, and from these calculations, it is demonstrated that the actuator utilizes only 1/15th the required energy to achieve a specific bending angle, and is four‐fold more power‐efficient than similar‐sized soft actuators and pumping systems reported in the literature. The integrated actuator and fluidic engine construct presented here thus represents a major departure from previous soft actuator control platforms in that everything is simplified down to a single self‐contained unit, demonstrating unparalleled versatility and modularity.
- 3 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 4 (4) , 3348-3354
Design, Fabrication, and Characterization of an Untethered Amphibious Sea Urchin-Inspired Robot
Sea urchins can easily navigate a wide range of challenging environments through the coordinated action of thousands of individually addressable rigid protective spines and flexible, reversibly adhesive tube feet. To investigate the potential implementation of these unusual locomotory appendages in a robotic context, we describe here the design, fabrication, and characterization of an untethered sea urchin-inspired robot driven by fluidic soft actuators. Due to the intrinsic design and fabrication difficulties in attempting to replicate the complexity of an adult sea urchin, we instead focused our attention on the development of a design that closely mimicked the body plan of an anatomically much simpler post-larval juvenile urchin. Consistent with its biological counterpart, our robotic prototype contained five flexible tube feet and ten rigid spines that could be independently driven by soft tripod actuators. Through the incorporation of permanent magnets into the distal ends of the flexible tube feet, our sea urchin-inspired robot could easily navigate across ferrous surfaces while adopting gaits and defensive postures that were surprisingly similar to its biological analog.
- 3 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 4 (4) , 3348-3354
Design, Fabrication, and Characterization of an Untethered Amphibious Sea Urchin-Inspired Robot
Sea urchins can easily navigate a wide range of challenging environments through the coordinated action of thousands of individually addressable rigid protective spines and flexible, reversibly adhesive tube feet. To investigate the potential implementation of these unusual locomotory appendages in a robotic context, we describe here the design, fabrication, and characterization of an untethered sea urchin-inspired robot driven by fluidic soft actuators. Due to the intrinsic design and fabrication difficulties in attempting to replicate the complexity of an adult sea urchin, we instead focused our attention on the development of a design that closely mimicked the body plan of an anatomically much simpler post-larval juvenile urchin. Consistent with its biological counterpart, our robotic prototype contained five flexible tube feet and ten rigid spines that could be independently driven by soft tripod actuators. Through the incorporation of permanent magnets into the distal ends of the flexible tube feet, our sea urchin-inspired robot could easily navigate across ferrous surfaces while adopting gaits and defensive postures that were surprisingly similar to its biological analog.
- 28 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 3 (3) , 2222-2228
Echinoderm-Inspired Tube Feet for Robust Robot Locomotion and Adhesion
Movement in echinoderms is facilitated by the coordinated activity of thousands of individually addressable and reversibly adhesive tube feet. To investigate the potential applicability of these unique biological actuators as a locomotory structure for robotics applications, we describe here the design, fabrication, and evaluation of an elastomeric structural analogue. The synthetic tube feet were modeled as bistable deformable domes, containing an embedded magnet to facilitate the reversible attachment to ferromagnetic materials. Two unique robots were developed using the bistability of these domes - CircleBot, which is capable of rolling on ferrous surfaces using a pull and roll technique, and PlanarBot, which uses a programmed deflection direction in the domes to move in a plane.
- 28 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 3 (3) , 2222-2228
Echinoderm-Inspired Tube Feet for Robust Robot Locomotion and Adhesion
Movement in echinoderms is facilitated by the coordinated activity of thousands of individually addressable and reversibly adhesive tube feet. To investigate the potential applicability of these unique biological actuators as a locomotory structure for robotics applications, we describe here the design, fabrication, and evaluation of an elastomeric structural analogue. The synthetic tube feet were modeled as bistable deformable domes, containing an embedded magnet to facilitate the reversible attachment to ferromagnetic materials. Two unique robots were developed using the bistability of these domes - CircleBot, which is capable of rolling on ferrous surfaces using a pull and roll technique, and PlanarBot, which uses a programmed deflection direction in the domes to move in a plane.