Huai-Cong Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Huai-Cong Liu has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
Ju Lee
Department of Electrical Engineering, Hanyang University, Seoul, Korea
14 shared publications- Sooyoung Cho
Department of Electrical Engineering, Hanyang University, Seoul, South Korea
9 shared publications - Ju Lee
Hanyang University
6 shared publications - Hyung-Woo Lee
Department of Railway Vehicle System Engineering, Korea National University of Transportation, 157, Cheoldobangmulgwan-ro, Uiwang-si 16106, Republic of Korea
5 shared publications - Geochul Jeong
Department of Electrical Engineering, Hanyang University, Seoul, South Korea
4 shared publications - Hyun-Seok Hong
Department of Electrical Engineering, Hanyang University, Seoul, South Korea
4 shared publications
Latest Publications
- 30 June 2019
- Published by The Korean Magnetics Society in Journal of Magnetics
- Vol. 24 (2) , 240-245
Effect of Material Characteristics on PMDC Motors based on the Grade of Electrical Steel Sheet
In this study, the effect of the material characteristics of electrical steel sheet on permanent magnet direct current (PMDC) motors is investigated using finite-element analysis. The motor design and test results are examined and verified through fabrication. The characterizations of brushless direct current (BLDC) motors according to the materials used in their cores have been actively studied. On the other hand, the effect of material characteristics on a PMDC motor consisting of brushes and commutators has not been studied as much. In the case of the PMDC motors, electrical steel sheets are infrequently used because this motor is relatively smaller than the BLDC motor. However, the iron loss characteristics, which are proportional to the frequency and the magnetic flux density, affect the efficiency even in small motors. Further, the output of the motor changes owing to saturation due to iron loss. The outcome presented in this study provides core materials selection guidelines to improve motor efficiency.
- 30 June 2019
- Published by The Korean Magnetics Society in Journal of Magnetics
- Vol. 24 (2) , 240-245
Effect of Material Characteristics on PMDC Motors based on the Grade of Electrical Steel Sheet
In this study, the effect of the material characteristics of electrical steel sheet on permanent magnet direct current (PMDC) motors is investigated using finite-element analysis. The motor design and test results are examined and verified through fabrication. The characterizations of brushless direct current (BLDC) motors according to the materials used in their cores have been actively studied. On the other hand, the effect of material characteristics on a PMDC motor consisting of brushes and commutators has not been studied as much. In the case of the PMDC motors, electrical steel sheets are infrequently used because this motor is relatively smaller than the BLDC motor. However, the iron loss characteristics, which are proportional to the frequency and the magnetic flux density, affect the efficiency even in small motors. Further, the output of the motor changes owing to saturation due to iron loss. The outcome presented in this study provides core materials selection guidelines to improve motor efficiency.
- 27 November 2018
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 48 (3) , 1421-1428
Design of a Double-Path Magnetic Circuit Structure Hybrid Fuel Injector Considering Demagnetization Characteristics
- 27 November 2018
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 48 (3) , 1421-1428
Design of a Double-Path Magnetic Circuit Structure Hybrid Fuel Injector Considering Demagnetization Characteristics
- 27 November 2018
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 48 (3) , 1386-1394
Design and Analysis of an IE4 Class Line-Start Synchronous Reluctance Motor Considering Total Loss and Starting Performance
- 27 November 2018
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 48 (3) , 1386-1394
Design and Analysis of an IE4 Class Line-Start Synchronous Reluctance Motor Considering Total Loss and Starting Performance
- 24 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 54 (11) , 1-5
Optimal Design of an Ultra-Premium-Efficiency PMA-Synchronous Reluctance Motor With the Winding Method and Stator Parameters to Reduce Flux Leakage and Minimize Torque Pulsations
In this paper, the optimal design for a permanent magnet-assisted synchronous reluctance motor (PMA-SynRM) is proposed in terms of efficiency, maximum torque, and minimum torque pulsations. Design variables, objective functions, and constraints are selected for this optimal design, which is divided into two steps. Step I utilizes the pole/slot combination of the PMA-SynRM and winding methods. The chosen 4-pole/36-slot model with distributed winding maximizes the rated efficiency. In Step II, the optimal design of the stator parameters is obtained using the response surface method and the precise torque and torque ripple are calculated using the finite-element analysis (FEA). The proposed stator slot openings are minimized to minimize the air-gap flux leakage, and consequently, realize a smooth electromagnetic torque. Finally, a few FEA results are validated by experimental results.
- 24 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 54 (11) , 1-5
Optimal Design of an Ultra-Premium-Efficiency PMA-Synchronous Reluctance Motor With the Winding Method and Stator Parameters to Reduce Flux Leakage and Minimize Torque Pulsations
In this paper, the optimal design for a permanent magnet-assisted synchronous reluctance motor (PMA-SynRM) is proposed in terms of efficiency, maximum torque, and minimum torque pulsations. Design variables, objective functions, and constraints are selected for this optimal design, which is divided into two steps. Step I utilizes the pole/slot combination of the PMA-SynRM and winding methods. The chosen 4-pole/36-slot model with distributed winding maximizes the rated efficiency. In Step II, the optimal design of the stator parameters is obtained using the response surface method and the precise torque and torque ripple are calculated using the finite-element analysis (FEA). The proposed stator slot openings are minimized to minimize the air-gap flux leakage, and consequently, realize a smooth electromagnetic torque. Finally, a few FEA results are validated by experimental results.
- 18 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 55 (2) , 1-4
Optimal Slot Design of IPMSM in Railway With Independently Rotating Wheelsets
This paper proposes a quasi-semi-closed (QSC) slot design method for an open-slot-type interior permanent magnet synchronous motor (IPMSM) for independently rotating wheelsets necessary to reduce the total harmonic distortion of no-load back-electromotive force and the torque ripple in the IPMSM. Four different slot-opening models were selected--the basic model, hairpin coil model, magnetic-wedge model, and QSC-slot model--and 2-D finite-element analysis was performed under open-circuit and load operations for each of the four models. Next, the relationships among the cogging torque, the torque ripple, and the saturation phenomenon in the core were analyzed. In addition, the manufacturing process, manufacturing cost, fill factor, end-winding resistance, copper loss, and efficiency were investigated. The experimental results verify the accuracy of the proposed method.
- 18 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 55 (2) , 1-4
Optimal Slot Design of IPMSM in Railway With Independently Rotating Wheelsets
This paper proposes a quasi-semi-closed (QSC) slot design method for an open-slot-type interior permanent magnet synchronous motor (IPMSM) for independently rotating wheelsets necessary to reduce the total harmonic distortion of no-load back-electromotive force and the torque ripple in the IPMSM. Four different slot-opening models were selected--the basic model, hairpin coil model, magnetic-wedge model, and QSC-slot model--and 2-D finite-element analysis was performed under open-circuit and load operations for each of the four models. Next, the relationships among the cogging torque, the torque ripple, and the saturation phenomenon in the core were analyzed. In addition, the manufacturing process, manufacturing cost, fill factor, end-winding resistance, copper loss, and efficiency were investigated. The experimental results verify the accuracy of the proposed method.
- 13 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 54 (11) , 1-5
Design, Modeling, and Analysis of a Railway Traction Motor With Independently Rotating Wheelsets
A conventional railway vehicle adopts the rigid-axle wheelset (RW) due to its inherently characteristics of automatic restoration capability without additional actuators or control. RW allows the railway vehicle to run to the center of the rail. However, there is no restoring force in independently rotating wheelsets (IRWs), if only traction torque control is applied as in RW. As a result, excessive wear and noise between the rail and the wheel are generated, and in severe cases a derailment may occur. In order for IRWs to generate restoring force, an active control strategy is needed that controls the left and right wheel torques independently. Because of this control characteristic, unlike the conventional traction motor of RW, fast torque response and precise torque control performance are required. In this paper, the design and modeling of an IRW traction motor were accomplished considering active restoring force control. A quasi-semi-closed slot structure is proposed to improve the power density and restoring torque control performance. In the next step, control simulation was performed using a static interior permanent magnet synchronous motor model considering slot harmonics. The validity of the proposed methods was verified through experiments using a dynamo.
- 13 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 54 (11) , 1-5
Design, Modeling, and Analysis of a Railway Traction Motor With Independently Rotating Wheelsets
A conventional railway vehicle adopts the rigid-axle wheelset (RW) due to its inherently characteristics of automatic restoration capability without additional actuators or control. RW allows the railway vehicle to run to the center of the rail. However, there is no restoring force in independently rotating wheelsets (IRWs), if only traction torque control is applied as in RW. As a result, excessive wear and noise between the rail and the wheel are generated, and in severe cases a derailment may occur. In order for IRWs to generate restoring force, an active control strategy is needed that controls the left and right wheel torques independently. Because of this control characteristic, unlike the conventional traction motor of RW, fast torque response and precise torque control performance are required. In this paper, the design and modeling of an IRW traction motor were accomplished considering active restoring force control. A quasi-semi-closed slot structure is proposed to improve the power density and restoring torque control performance. In the next step, control simulation was performed using a static interior permanent magnet synchronous motor model considering slot harmonics. The validity of the proposed methods was verified through experiments using a dynamo.
- 2 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 65 (4) , 3104-3114
Optimum Design of an IE4 Line-Start Synchronous Reluctance Motor Considering Manufacturing Process Loss Effect
As a kind of direct-on-line motor, super premium efficiency (IE4) line-start synchronous reluctance motors (LS-SynRMs) were developed recently and are now used in many applications, including fans, pumps, and compressors. This paper presents an optimum design and comparative study of LS-SynRMs with additional losses and impact during the manufacturing process (electrical steel cutting/punching damage as well as squirrel-cage die-casting with bubble effects). The work results indicate that the LS-SynRM design with the “manufacturing process loss” effect should be considered and compensated for the design in order to achieve an IE4 class efficiency and ensure synchronization. Furthermore, the LS-SynRM rotor with multilayer flux barriers and rotor slots is investigated in detail. The influences of optimum design geometrical parameters (flux barriers thickness, segments thickness, length of rotor slots, etc.) on the performances of the basic model and optimum design model are evaluated with finite-element analysis (FEA) results. For more accurate results, the effects of saturation, saliency ratio, inductance difference, and the change in the B-H/B-P curve in damaged motor core edges are considered. Meanwhile, in the squirrel cage, the porosity rate distributions are considered. The copper loss, iron loss, starting torque, power factor, efficiency, and synchronization ability are investigated. The experimental results verify the accuracy of the process presented in this paper.
- 2 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 65 (4) , 3104-3114
Optimum Design of an IE4 Line-Start Synchronous Reluctance Motor Considering Manufacturing Process Loss Effect
As a kind of direct-on-line motor, super premium efficiency (IE4) line-start synchronous reluctance motors (LS-SynRMs) were developed recently and are now used in many applications, including fans, pumps, and compressors. This paper presents an optimum design and comparative study of LS-SynRMs with additional losses and impact during the manufacturing process (electrical steel cutting/punching damage as well as squirrel-cage die-casting with bubble effects). The work results indicate that the LS-SynRM design with the “manufacturing process loss” effect should be considered and compensated for the design in order to achieve an IE4 class efficiency and ensure synchronization. Furthermore, the LS-SynRM rotor with multilayer flux barriers and rotor slots is investigated in detail. The influences of optimum design geometrical parameters (flux barriers thickness, segments thickness, length of rotor slots, etc.) on the performances of the basic model and optimum design model are evaluated with finite-element analysis (FEA) results. For more accurate results, the effects of saturation, saliency ratio, inductance difference, and the change in the B-H/B-P curve in damaged motor core edges are considered. Meanwhile, in the squirrel cage, the porosity rate distributions are considered. The copper loss, iron loss, starting torque, power factor, efficiency, and synchronization ability are investigated. The experimental results verify the accuracy of the process presented in this paper.
- 24 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 53 (11) , 1-5
Eddy Current Brake With a Two-Layer Structure: Calculation and Characterization of Braking Performance
This paper presents a new method for calculating the braking force of a drum-type eddy current brake with a two-layer structure. The drum-type eddy current brake should have a structure that improves the braking force by applying a material with high conductivity inside the drum because the eddy current loss generated from the drum is used as the braking force. In addition, because the eddy current brake operates at various speeds while braking the vehicle, it is necessary to grasp the braking force according to the speed. Furthermore, because the material of the drum is composed of non-laminated iron having conductivity, the skin effect and the armature reaction phenomenon appear, and the skin depth and the air-gap flux density are different depending on the braking speed. In this paper, the value of the eddy current loss of the eddy current brake with a copper coating inside the drum is newly presented and compared with the finite-element analysis results. In addition, the change in the speed-torque curve according to the conductivity value of the drum and inner coating material are shown. Finally, an experiment was conducted to compare and verify the characteristic curve of the eddy current brake obtained from the newly derived equations.
- 24 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 53 (11) , 1-5
Eddy Current Brake With a Two-Layer Structure: Calculation and Characterization of Braking Performance
This paper presents a new method for calculating the braking force of a drum-type eddy current brake with a two-layer structure. The drum-type eddy current brake should have a structure that improves the braking force by applying a material with high conductivity inside the drum because the eddy current loss generated from the drum is used as the braking force. In addition, because the eddy current brake operates at various speeds while braking the vehicle, it is necessary to grasp the braking force according to the speed. Furthermore, because the material of the drum is composed of non-laminated iron having conductivity, the skin effect and the armature reaction phenomenon appear, and the skin depth and the air-gap flux density are different depending on the braking speed. In this paper, the value of the eddy current loss of the eddy current brake with a copper coating inside the drum is newly presented and compared with the finite-element analysis results. In addition, the change in the speed-torque curve according to the conductivity value of the drum and inner coating material are shown. Finally, an experiment was conducted to compare and verify the characteristic curve of the eddy current brake obtained from the newly derived equations.
- 23 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 53 (11) , 1-5
Design and Analysis of a Double-Layer Magnetic Circuit Structure for High-Force Density Hybrid Fuel Injector
This paper proposes the design and analysis of a double-layer magnetic circuit structure for a high-force density hybrid fuel injector. In general, fuel injector models have disadvantages such as a significant leakage flux and magnetic saturation; therefore, a finite-element method is used to detail the model design and reduce the leakage flux from the electromagnet pole to the lead pipe. This change can help improve the fuel injector performance. In addition, a permanent magnet (PM) is inserted to increase the force density. Moreover, the no-load performance and demagnetization characteristic of the injector are analyzed according to the injector's working environment. The optimized hybrid fuel injector model with a PM shows substantially improved performance compared to a conventional design.
- 23 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 53 (11) , 1-5
Design and Analysis of a Double-Layer Magnetic Circuit Structure for High-Force Density Hybrid Fuel Injector
This paper proposes the design and analysis of a double-layer magnetic circuit structure for a high-force density hybrid fuel injector. In general, fuel injector models have disadvantages such as a significant leakage flux and magnetic saturation; therefore, a finite-element method is used to detail the model design and reduce the leakage flux from the electromagnet pole to the lead pipe. This change can help improve the fuel injector performance. In addition, a permanent magnet (PM) is inserted to increase the force density. Moreover, the no-load performance and demagnetization characteristic of the injector are analyzed according to the injector's working environment. The optimized hybrid fuel injector model with a PM shows substantially improved performance compared to a conventional design.