ZSZahra Saadatizadeh

Zahra Saadatizadeh

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Zahra Saadatizadeh has a total of 22 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • High-Frequency Three-Port DC–DC Converter With Zero-Voltage Switching Operation

    by Zahra Saadatizadeh, Pedram Chavoshipour Heris, Alan Mantooth

    In this article, an isolated zero-voltage switching three-port dc–dc converter (TPC) using a planer transformer is proposed and operated for the frequency of 1 MHz. The proposed converter has a bidirectional operation. In the proposed converter, the main transformer is used to isolate low dc voltage ports from the high dc voltage port and to increase the voltage conversion ratio of the secondary side port, which supplies the load. The proposed converter is partially isolated TPC and has the advantage of galvanically isolation between one of the ports which are interfaced to the main load and the other two ports (input and storage-side ports) are nonisolated and common-grounded. The proposed converter is compared with other recent converters of the same type, and it is concluded that the proposed converter has achieved the capabilities of having an isolated structure with lower volume, interfacing three different dc voltages in the three dc ports, having the bidirectional operation, high-voltage gain, zero-voltage switching operation of all four switches, simple switching pattern, achieving simple controlling way for all ranges of duty cycles both step-up and step-down operations, utilizing a nonlinear digital controlling system, smaller size, higher operating frequency, higher efficiency, and high power density.


  • A Simple Switching-Event Dependent High-Frequency Sampling Method for Power Conversion System

    by Liyang Du, Hui Cao, Zahra Saadatizadeh, Yue Zhao, H. Alan Mantooth

    Precise current and voltage sensing are challenging for digital control in high-frequency power conversion systems. Given that the power electronics circuitry is triggered repetitively by power device switching events, a switching-time-dependent sampling method is proposed to realize an equivalent high-frequency signal sampling with a low-speed analog digital converter (ADC) and digital controller. Two sampling modes are developed in the proposed methods in terms of sampling rates lower and higher than the digital controller clock frequency, respectively. A fast and simple signal reconstruction method is designed to ensure the feasibility of a low-cost processor. A series-resonant dual-active-bridge is taken as an example for the theoretical analysis and experimental verification. The resonant current and Miller plateau voltage in the topology are sampled to verify the potential of the proposed method for online parameter recognition of dc–dc converters and device behavior monitoring of power devices.


  • Hybrid Si/SiC Switches: A Review of Control Objectives, Gate Driving Approaches and Packaging Solutions

    by Dereje Woldegiorgis, Maksudul Hossain, Zahra Saadatizadeh, Yuqi Wei, H. Alan Mantooth

    Hybrid Si/SiC switches are gaining increased attention for designing high-efficiency and high-power density energy conversion systems. They offer very good conduction and switching power loss performance compared to using only Si IGBT or SiC MOSFET devices as a result of combining the best properties of both devices. Several Si/SiC gate control strategies, gate driving approaches, and packaging considerations have been proposed in the literature. This paper presents a comprehensive review and performance comparison of the different Si/SiC gate control strategies, gate driver solutions and packaging approaches that are already proposed in literature. In addition, it aims to provide a general guideline for selecting the appropriate Si/SiC gate control approach that is suitable for different applications considering several Si/SiC switch design properties. It also aims to establish a general metrics for evaluating the performance of different Si/SiC gate driver solutions that are proposed in literature in order to help the designer choose a suitable gate driver solution for different applications. Moreover, it highlights future research and development needs of hybrid Si/SiC switches in terms of gate control techniques, gate driver approaches and packaging solutions in order to achieve further performance improvements and fully exploit their benefits.


  • Open Access

    Modular Expandable Multiinput Multioutput (MIMO) High Step-Up Transformerless DC–DC Converter

    by Zahra Saadatizadeh, Pedram Chavoshipour Heris, H. Alan Mantooth

    In this paper, a Multi-Input Multi-Output (MIMO) high step-up transformerless DC-DC converter is proposed. The proposed converter can expand the number of ports from both input and output terminals. Also, it has a modular structure using voltage multiplier cells (a switch, two diodes, a capacitor, and an inductor). The proposed converter is useful for a wide range of applications and has the merit of interfacing multiple hybrid voltage sources with each other to supply different loads with various voltage levels. All the output voltages of the output ports can be regulated at the same time by tuning separate controlling parameters. Since digital control has the benefit of (1) enhancing efficiency, (2) higher flexibility than analog electronics, (3) ease of use, (4) improving reliability and stability in hybrid energy conversion applications, this method of controlling implementation is adopted. The key contributions of this article would be 1) expandable modular MIMO converter with high performance for all range of duty cycles; 2) integration of hybrid energy sources and delivering to multiple loads; 3) nonlinear digital controlling approach to achieve fast transient response under the variation of input voltage sources and output loads, and 4) high voltage gain with low normalized power stress on switches. To simplify the analysis, first, single-input, dual-output (SIDO) mother-module, dual-input, three-output (DITO) and three-input, four-output (TIFO) developed modules are carefully analyzed and then, the MIMO structure is explained. To verify the theoretical results, a prototype of SIDO operation of the proposed converter with a digital controlling scheme is implemented for 30V input voltage /150V, 250V output voltages with the total power of 450W. Furthermore, experimental results of DITO operation with 30V and 40V input voltages/150V, 250V, 405V output voltages with the total power of 800W are extracted.


  • Open Access

    Expandable Non-Isolated Multi-Input Single-Output DC-DC Converter With High Voltage Gain and Zero-Ripple Input Currents

    by Zahra Saadatizadeh, Pedram Chavoshipour Heris, Xiaodong Liang, Ebrahim Babaei

    In this paper, an expandable non-isolated multi-input single-output DC-DC high voltage gain converter with the capability of cancelling input current ripples is proposed, which can be applied in photovoltaic (PV) systems. The proposed converter has several advantages including: 1) it provides a single voltage gain for the whole range of duty cycles; 2) the duty cycle’s operating range is not decreased when increasing the number of input stages; 3) it has a simple switching pattern, and all switches go on and off, simultaneously; 4) the current ripple of each input stage is eliminated for the whole range of duty cycles; 5) the output load has a common ground with all input voltage sources; and 6) the voltage stress on switches is low. In this paper, the proposed converter in a dual-input single-output (DISO) form is introduced at first, and its general form with multi-input single-output (MISO) is then analyzed. Following that, the voltage gain, voltage and current stresses on switches, diodes and capacitors, and input current ripple cancelling condition are calculated. Finally, experimental results are used to validate the calculated theoretical results.


  • Multi‐input multi‐phase transformerless large voltage conversion ratio DC/DC converter

    by Zahra Saadatizadeh, Pedram Chavoshipour Heris, Mehran Sabahi, Xiaodong Liang

    This paper proposes a two‐input transformerless DC‐DC converter. The proposed converter has large voltage conversion ratio with low‐voltage and current stress on semiconductors and low input current ripple. It can transfer energy as two‐phase converter with three and four input voltage sources to increase the availability of the input voltage of the converter. Despite the capability of extending the number of the input sources up to four, the range of operating duty cycle for the switches and the voltage conversion ratio are remained the same as the values for two‐input topology of the proposed converter. By increasing diode‐capacitor (D‐C) cells in upper and lower modules, not only the amount of transferred energy will be increased, but also the voltage stress on semiconductors would be decreased. In this paper, theoretical analysis for continuous current mode (CCM), analysis under discontinuous current mode (DCM), voltage gain and voltages and currents of all of the elements are calculated. Finally, the performance of the proposed converter is confirmed by implemented prototype which converts two 40‐V input voltages to output voltage of 600 V with the power of 400 W.


  • High‐voltage conversion ratio dual‐input DC–DC converter operating in a wide duty cycle range and canceling input current ripple

    by Pedram Chavoshipour Heris, Zahra Saadatizadeh, Mehran Sabahi, Xiaodong Liang

    This paper proposes a new nonisolated dual‐input, single‐output (DISO) DC–DC converter. In the proposed converter, by utilizing two three‐winding coupled inductors at the primary of each input ports, the capabilities of high‐voltage conversion ratio and elimination of input current ripple are achieved for all range of duty cycles (0 < D < 1). Therefore, the proposed converter is applicable in renewable energy systems. The voltage conversion ratio can be increased without selecting high duty cycles for the switches or by using a high number of components. Also, the voltage stresses on switches of the proposed converter are in low level. The proposed converter has simple switching pattern and the two switches turn on/off inversely. Unlike the interleaved converters, the proposed converter has a single conversion ratio for all adopted duty cycles of the switches (0 < D < 1). In this study, the proposed converter is analyzed and the required conditions for eliminating input current ripple, the voltage and current stress on the semiconductors, and the voltage gain are calculated. To confirm the theoretical results, experimental results are extracted for a 14‐V/19‐V input and 400‐V output voltages for the operating power of 350 W.


  • Open Access

    SIDO coupled inductor‐based high voltage conversion ratio DC–DC converter with three operations

    by Zahra Saadatizadeh, Pedram Chavoshipour Heris, Ebrahim Babaei, Frede Blaabjerg, Carlo Cecati

    Here, a single‐input, dual output (SIDO) coupled inductor‐based high voltage conversion ratio DC–DC converter is proposed. The proposed converter has the capability of operating as a SIDO converter in a way that the terminal of the input voltage source is exchangeable among the three ports. Therefore, there are three different operation modes for the proposed converter. The voltage conversion ratios of the high voltage ports over the low voltage port can be improved by increasing the turn ratio of the coupled inductors. The main advantage of the proposed converter is achieving high voltage gains with lower number of components for the whole range of duty cycles comparing to the conventional multi‐port high voltage gain converters. Moreover, two output voltages of the proposed converter can be simultaneously regulated on different constant levels with a good precision. In this study, the voltage conversion ratios, the inductors’ average currents, the voltage and current stress on the switches are calculated theoretically. Finally, an experimental prototype of 30 V input and 410, 260 V outputs with the power 510 W is implemented and the results are verifying the theoretical ones.


  • Open Access

    Single input, dual output high step‐up/down DC–DC converter with ripple‐free input current in the high current port and expandable number of output ports

    by Zahra Saadatizadeh, Ebrahim Babaei, Frede Blaabjerg, Carlo Cecati

    In this study, a non‐isolated three‐port high step‐up/step‐down DC–DC converter is proposed. The proposed converter has the capability of cancelling the input current ripple in the high current port, moreover, the voltage conversion ratios between the high voltage and low voltage are increased by coupled inductors. All the ports of the proposed converter have a common ground. In addition, any of the three ports can be used as an input voltage source, which can supply the other two ports. The number of DC voltage ports of the proposed converter can be more increased by using more inductor‐switch cells. In this study, the theoretical results of the proposed converter are obtained and the voltage conversion ratios of the output ports, the voltage and current stress on switches, average currents of inductors, and the required condition of cancelling input current ripple at the low voltage side are calculated for the proposed three‐port converter. The voltage gains of the developed converter with four ports are also calculated. Finally, the theoretical results are reconfirmed by the experimental results for 28 V input/150 and 460 V output ports.


  • Three-Port High Step-Up and High Step-Down DC-DC Converter With Zero Input Current Ripple

    by Zahra Saadatizadeh, Ebrahim Babaei, Frede Blaabjerg, Carlo Cecati

    In this paper, a non-isolated three-port DC-DC converter with high voltage conversion ratio is proposed. In the proposed converter, by changing the place of input voltage source between each of the three ports, three different single-input two-output operation modes are achieved. The input current ripple of the proposed converter is eliminated at the low voltage side for the whole range of duty cycles. The voltage conversion ratios of the proposed converter can be increased by increasing the turns ratio of second winding of coupled inductors. Moreover, the proposed converter has achieved proper output voltage regulations for all output ports, simultaneously. The proposed converter can be utilized in the renewable energy conversion systems such as in photovoltaic and fuel cells. In this study, the voltage conversion ratios of the output ports, the voltage stress on switches, the average currents of switches and inductors and the required condition for cancelling input current ripple at low voltage side are calculated theoretically. The theoretical results are verified and experimental results for 24 V input voltage and 304 V, 240 V output voltages with 400 W power are extracted for two different operation modes.