Giuseppe Addamo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Giuseppe Addamo has a total of 186 co-authors. Here are the top co-authors by number of shared publications:
- Giuseppe Virone
National Research Council of Italy, Institute of Electronics, Information Engineering and Telecommunication (CNR-IEIIT), Turin, Italy
27 shared publications - Oscar Antonio Peverini
Consiglio Nazionale delle Ricerche, Istituto di Elettronica e di Ingegneria dell'Informazione e delle Telecomunicazioni (CNR-IEIIT), Corso Duca degli Abruzzi, 24, 10129 Turin, Italy
21 shared publications - Fabio Paonessa
Consiglio Nazionale delle Ricerche (CNR), Institute of Electronics, Information and Telecommunications Engineering (IEIIT), Italy
13 shared publications - Mauro Lumia
IEIIT, National Research Council, 10129 Torino, Italy
11 shared publications - Diego Manfredi
Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Turin, Italy
8 shared publications - Flaviana Calignano
Department of Management and Production Engineering, Politecnico di Torino, 10129 Torino, Italy
6 shared publications
Latest Publications
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- p. 1-15
Integrated PCB-to-Waveguide Feed Element for Ka-Band Active Antennas in Dual-Circular Polarization
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- p. 1-15
Open AccessIntegrated PCB-to-Waveguide Feed Element for Ka-Band Active Antennas in Dual-Circular Polarization
- Open Access
Ka-Band Reflectarray with Cylindrical Dielectric Unit Cells: Optimized Additive Manufacturing and High-Permittivity Material Characterization
This paper discusses the design, manufacturing, and experimental characterization of a Ka-band fully dielectric reflectarray realized using Zetamix 7.5 ceramic material and additive manufacturing. Properly tuning the infill during the manufacturing process, it is possible to control the permittivity of the material, which can therefore be considered, to all intents and purposes, an additional degree of freedom for optimizing the unit cell and consequently the reflectarray performance. The optimal values of are determined through numerical analysis of the unit cell and experimental characterization of bricks manufactured with different printing parameters. Then, the unit cell is used to design a medium-sized reflectarray with an aperture of 207.4 and a thickness of 0.44, at the design frequency GHz. The full-wave simulations of the designed RA and experimental measurements of a prototype confirm the excellent performance of the antenna, which exhibits a broadband flat response from 28 to 31 GHz and an aperture efficiency exceeding 50%.Open AccessKa-Band Reflectarray with Cylindrical Dielectric Unit Cells: Optimized Additive Manufacturing and High-Permittivity Material Characterization
This paper discusses the design, manufacturing, and experimental characterization of a Ka-band fully dielectric reflectarray realized using Zetamix 7.5 ceramic material and additive manufacturing. Properly tuning the infill during the manufacturing process, it is possible to control the permittivity of the material, which can therefore be considered, to all intents and purposes, an additional degree of freedom for optimizing the unit cell and consequently the reflectarray performance. The optimal values of are determined through numerical analysis of the unit cell and experimental characterization of bricks manufactured with different printing parameters. Then, the unit cell is used to design a medium-sized reflectarray with an aperture of 207.4 and a thickness of 0.44, at the design frequency GHz. The full-wave simulations of the designed RA and experimental measurements of a prototype confirm the excellent performance of the antenna, which exhibits a broadband flat response from 28 to 31 GHz and an aperture efficiency exceeding 50%. - Open Access
- 1 June 2025
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 20 (06) , P06057
On beam characterization of ground-based CMB radio telescopes using UAV-mounted sources: application to the QUIJOTE TFGI and plans for LSPE-Strip
The Large Scale Polarization Explorer (LSPE) project, funded by the Italian Space Agency (ASI), includes the development of LSPE-Strip, a ground-based radio telescope for observing Cosmic Microwave Background (CMB) anisotropies. LSPE-Strip, nearing its construction phase, will operate from the Teide Observatory in Tenerife, employing 49 coherent polarimeters at 43 GHz to deliver critical data on CMB anisotropies and 6 channels at 95 GHz as atmospheric monitor. On-site characterization of such advanced instruments is crucial to detect possible systematic effects, such as gain fluctuations, beam distortions, and pointing errors, that can compromise performance by introducing spurious polarizations or radiation collection from unintended directions. To address these challenges, a drone-mounted Q-band test source for on-site characterization of LSPE-Strip's polarimeter array was developed. Modern Unmanned Aerial Vehicles (UAVs) offer a flexible approach for antenna pattern measurements, yet their use in high-frequency radio astronomy is not consolidated practice. In October 2022, a UAV-based measurement campaign was conducted with the TFGI instrument on the second QUIJOTE telescope in Tenerife, in collaboration with the Instituto de Astrofísica de Canarias. This pioneering effort aimed to validate UAV-based beam characterization methods and assess QUIJOTE's performance under operational conditions. Preliminary results demonstrated high measurement accuracy, leveraging QUIJOTE's dual-receiver configuration for beam validation. These findings provide valuable insights for optimizing UAV systems in preparation for LSPE-Strip's future characterization.
- 1 June 2025
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 20 (06) , P06057
Open AccessOn beam characterization of ground-based CMB radio telescopes using UAV-mounted sources: application to the QUIJOTE TFGI and plans for LSPE-Strip
The Large Scale Polarization Explorer (LSPE) project, funded by the Italian Space Agency (ASI), includes the development of LSPE-Strip, a ground-based radio telescope for observing Cosmic Microwave Background (CMB) anisotropies. LSPE-Strip, nearing its construction phase, will operate from the Teide Observatory in Tenerife, employing 49 coherent polarimeters at 43 GHz to deliver critical data on CMB anisotropies and 6 channels at 95 GHz as atmospheric monitor. On-site characterization of such advanced instruments is crucial to detect possible systematic effects, such as gain fluctuations, beam distortions, and pointing errors, that can compromise performance by introducing spurious polarizations or radiation collection from unintended directions. To address these challenges, a drone-mounted Q-band test source for on-site characterization of LSPE-Strip's polarimeter array was developed. Modern Unmanned Aerial Vehicles (UAVs) offer a flexible approach for antenna pattern measurements, yet their use in high-frequency radio astronomy is not consolidated practice. In October 2022, a UAV-based measurement campaign was conducted with the TFGI instrument on the second QUIJOTE telescope in Tenerife, in collaboration with the Instituto de Astrofísica de Canarias. This pioneering effort aimed to validate UAV-based beam characterization methods and assess QUIJOTE's performance under operational conditions. Preliminary results demonstrated high measurement accuracy, leveraging QUIJOTE's dual-receiver configuration for beam validation. These findings provide valuable insights for optimizing UAV systems in preparation for LSPE-Strip's future characterization.
- Open Access
- 3 May 2025
- Published by MDPI AG in Electronics
- Vol. 14 (9) , 1865
Investigation into Applicability of 3D-Printed Composite Polymers with Enhanced Mechanical Properties in the Development of Microwave Components
Additive manufacturing is currently regarded as one of the enabling technologies for Space Economy since it allows for the reduction of lead time and costs of payloads and platforms. Typically, metal-based additive manufacturing technologies are considered for the development of microwave components for Space applications since they exhibit the best trade-off in radio-frequency performance, benefits, and withstanding adverse environmental conditions. In this view, composite polymers may further increase the benefits arising from the 3D printing of microwave components since lighter parts with the required thermal, mechanical, and RF performances can be placed on board satellites. This paper explores the feasibility of 3D-printed composite polymers, including Ultem and PEEK reinforced with carbon fiber, for the development of microwave waveguide devices intended for Space applications. To this end, three different manufacturing routes were investigated by selecting a specific composite polymer, the corresponding manufacturing system and post-processing, and the necessary metal-plating technique. Hence, relevant radio-frequency test vehicles operating at 10 ÷ 14 GHz were designed, manufactured, and tested. The experimental results prove that waveguide components operating in X and Ku bands can be developed through the material extrusion of PEEK reinforced with carbon fiber, which is subsequently metalized by means of a two-stage electroless/electroplating process.
- 3 May 2025
- Published by MDPI AG in Electronics
- Vol. 14 (9) , 1865
Open AccessInvestigation into Applicability of 3D-Printed Composite Polymers with Enhanced Mechanical Properties in the Development of Microwave Components
Additive manufacturing is currently regarded as one of the enabling technologies for Space Economy since it allows for the reduction of lead time and costs of payloads and platforms. Typically, metal-based additive manufacturing technologies are considered for the development of microwave components for Space applications since they exhibit the best trade-off in radio-frequency performance, benefits, and withstanding adverse environmental conditions. In this view, composite polymers may further increase the benefits arising from the 3D printing of microwave components since lighter parts with the required thermal, mechanical, and RF performances can be placed on board satellites. This paper explores the feasibility of 3D-printed composite polymers, including Ultem and PEEK reinforced with carbon fiber, for the development of microwave waveguide devices intended for Space applications. To this end, three different manufacturing routes were investigated by selecting a specific composite polymer, the corresponding manufacturing system and post-processing, and the necessary metal-plating technique. Hence, relevant radio-frequency test vehicles operating at 10 ÷ 14 GHz were designed, manufactured, and tested. The experimental results prove that waveguide components operating in X and Ku bands can be developed through the material extrusion of PEEK reinforced with carbon fiber, which is subsequently metalized by means of a two-stage electroless/electroplating process.
- Open Access
Feasibility Study on Additive Manufacturing of Feed Horn Operating in D-Band
This paper presents the outcomes of a feasibility study on the manufacturing of D-band horn antennas through the Low Power Bed Fusion process. Different prototypes have been realized and tested, showing nice results in terms of the co-polarization component. On the other hand, a spurious cross-polarization component is present in the radiation pattern even in the principal planes, limiting the device to single-polarization applications. A mechanical study of the realized devices has been conducted on the horn internal channel to understand the reasons for this issue, and, subsequently, to address where to improve the manufacturing process.
Open AccessFeasibility Study on Additive Manufacturing of Feed Horn Operating in D-Band
This paper presents the outcomes of a feasibility study on the manufacturing of D-band horn antennas through the Low Power Bed Fusion process. Different prototypes have been realized and tested, showing nice results in terms of the co-polarization component. On the other hand, a spurious cross-polarization component is present in the radiation pattern even in the principal planes, limiting the device to single-polarization applications. A mechanical study of the realized devices has been conducted on the horn internal channel to understand the reasons for this issue, and, subsequently, to address where to improve the manufacturing process.
- Open Access
- 10 December 2024
- Published by MDPI AG in Preprints.org
Feasibility Study on AM Manufacturing of Feed Horn Operating in D-Band
This paper presents the outcomes of a feasibility study on the manufacturing of D-band horn antenna through Low Power Bed Fusion process. Different prototypes have been realized and tested showing nice results in terms of co-polarization component. On the other hand, a spurious cross-polarization component is present in the radiation pattern even in the principal planes, limiting the device to single polarization applications. A mechanical study of the realized devices has been conducted on the horn internal channel to understand the reasons of this issue and, subsequently, to address where improving the manufacturing process.
- 10 December 2024
- Published by MDPI AG in Preprints.org
Open AccessFeasibility Study on AM Manufacturing of Feed Horn Operating in D-Band
This paper presents the outcomes of a feasibility study on the manufacturing of D-band horn antenna through Low Power Bed Fusion process. Different prototypes have been realized and tested showing nice results in terms of co-polarization component. On the other hand, a spurious cross-polarization component is present in the radiation pattern even in the principal planes, limiting the device to single polarization applications. A mechanical study of the realized devices has been conducted on the horn internal channel to understand the reasons of this issue and, subsequently, to address where improving the manufacturing process.
- Open Access
- 9 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-13
Electromagnetics-Aware Path for UAV-Based Near-Field Antenna Measurements Implemented With a High Dynamic Range SDR
An electromagnetics-aware path for drone-based near-field antenna measurements is implemented in an outdoor experimentation. This technique allows to significantly reduce the scan duration with respect to a standard half-wavelength near-field scanning, using knowledge of the antenna under test electrical size only. The validity of our approach is corroborated with planar outdoor near-field measurements performed with an untethered drone transmitting at 750 MHz. To deal with the absence of phase coherence, the phase information is retrieved from a reference antenna, while a software-defined radio having four super-heterodyne receiving channels is used to properly sample the high-dynamic signals resulting from the large scanning surface.
- 9 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-13
Open AccessElectromagnetics-Aware Path for UAV-Based Near-Field Antenna Measurements Implemented With a High Dynamic Range SDR
An electromagnetics-aware path for drone-based near-field antenna measurements is implemented in an outdoor experimentation. This technique allows to significantly reduce the scan duration with respect to a standard half-wavelength near-field scanning, using knowledge of the antenna under test electrical size only. The validity of our approach is corroborated with planar outdoor near-field measurements performed with an untethered drone transmitting at 750 MHz. To deal with the absence of phase coherence, the phase information is retrieved from a reference antenna, while a software-defined radio having four super-heterodyne receiving channels is used to properly sample the high-dynamic signals resulting from the large scanning surface.
- Open Access
- 3 September 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (17) , 7825
Ridged Apertures for LEO Direct Radiating Arrays in Ka-Band
This paper presents an extensive performance analysis of open-ended waveguide elements for direct radiating arrays with a high scan angle (±50° /60°). The evaluated designs are based on square and hexagonal apertures loaded with ridges. Both square and triangular lattices are considered in the framework of Ka-band downlink design requirements for future LEO mega-constellations. The parameter space defined by the monomodal condition has been explored to find an optimum value for each structure. The analyses carried out with both infinite and finite full-wave models in terms of active reflection coefficient, scan loss and cross-polar discrimination are in good agreement.
- 3 September 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (17) , 7825
Open AccessRidged Apertures for LEO Direct Radiating Arrays in Ka-Band
This paper presents an extensive performance analysis of open-ended waveguide elements for direct radiating arrays with a high scan angle (±50° /60°). The evaluated designs are based on square and hexagonal apertures loaded with ridges. Both square and triangular lattices are considered in the framework of Ka-band downlink design requirements for future LEO mega-constellations. The parameter space defined by the monomodal condition has been explored to find an optimum value for each structure. The analyses carried out with both infinite and finite full-wave models in terms of active reflection coefficient, scan loss and cross-polar discrimination are in good agreement.
- Open Access
- 2 July 2024
- Published by MDPI AG in Preprints.org
Open-ended Ridged Waveguide Elements for LEO Direct Radiating Arrays in Ka-band
This paper presents an extensive performance analysis of open-ended waveguide elements for direct radiating arrays with high scan angle (± 50º/60º). The evaluated designs are based on square and hexagonal apertures loaded with ridges. Both square and triangular lattices are considered in the framework of Ka-band downlink design requirements for future LEO mega-constellations. The parameter space defined by the monomodal condition has been explored to find an optimum value for each structure. The analyses are validated with both infinite and finite full-wave models in terms of active reflection coefficient, scan loss and cross-polar discrimination.
- 2 July 2024
- Published by MDPI AG in Preprints.org
Open AccessOpen-ended Ridged Waveguide Elements for LEO Direct Radiating Arrays in Ka-band
This paper presents an extensive performance analysis of open-ended waveguide elements for direct radiating arrays with high scan angle (± 50º/60º). The evaluated designs are based on square and hexagonal apertures loaded with ridges. Both square and triangular lattices are considered in the framework of Ka-band downlink design requirements for future LEO mega-constellations. The parameter space defined by the monomodal condition has been explored to find an optimum value for each structure. The analyses are validated with both infinite and finite full-wave models in terms of active reflection coefficient, scan loss and cross-polar discrimination.
- Open Access
- 9 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 72
List of Reviewers
- 9 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 72
Open AccessList of Reviewers