Xuesong Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Xuesong Li has a total of 194 co-authors. Here are the top co-authors by number of shared publications:
Fangzhu Qing
20 shared publications- Fangzhu Qing
University of Electronic Science and Technology of China
12 shared publications Changqing Shen
State Key Laboratory of Electronic Thin Films and Integrated Devices, University of Electronic Science and Technology of China, Chengdu, China
10 shared publicationsYuting Hou
School of Integrated Circuit Science and Engineering (Exemplary School of Microelectronics) University of Electronic Science and Technology of China Chengdu 611731 China
6 shared publicationsXiaomeng Guo
University of Electronic Science and Technology of China
5 shared publicationsCongcong Ning
School of Integrated Circuit Science and Engineering (Exemplary School of Microelectronics)
4 shared publications
Latest Publications
- Open Access
- 24 September 2026
- Published by Elsevier in SSRN Electronic Journal
Meter-per-Minute Roll-to-Roll CVD Growth of Graphene by Pressure-Modulation with Cu Pre-Oxidation and Hydrogen-Free Chemistry
Roll-to-roll (R2R) chemical vapor deposition (CVD) has been pursued as a key enabling technology for continuous graphene production, yet its progress has long been constrained by a trade-off between growth rate and film quality. In atmospheric-pressure CVD, the carbon flux available for growth is limited because excessive methane flow promotes gas-phase side reactions that introduce defects. Low-pressure CVD suppresses these side reactions and improves transport, but at very low pressures the absolute CH4 partial pressure may be insufficient to adequate growth rates. Here we address this trade-off by systematically investigating the pressure-dependent growth behavior across the 5~760 Torr range in an industrial-scale R2R-CVD system, and develop a synergistic strategy combining Cu pre-oxidation with hydrogen-free precursor chemistry. The combined strategy yields high-quality continuous R2R monolayer graphene, with monolayer coverage > 90% and ID/IG < 5% at 1 m/min, and ~80% monolayer with ID/IG ~20% at 2 m/min. This work establishes a scalable route to meter-per-minute graphene production by decoupling the constraints on growth mode, defect suppression, and carbon delivery.
- 24 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMeter-per-Minute Roll-to-Roll CVD Growth of Graphene by Pressure-Modulation with Cu Pre-Oxidation and Hydrogen-Free Chemistry
Roll-to-roll (R2R) chemical vapor deposition (CVD) has been pursued as a key enabling technology for continuous graphene production, yet its progress has long been constrained by a trade-off between growth rate and film quality. In atmospheric-pressure CVD, the carbon flux available for growth is limited because excessive methane flow promotes gas-phase side reactions that introduce defects. Low-pressure CVD suppresses these side reactions and improves transport, but at very low pressures the absolute CH4 partial pressure may be insufficient to adequate growth rates. Here we address this trade-off by systematically investigating the pressure-dependent growth behavior across the 5~760 Torr range in an industrial-scale R2R-CVD system, and develop a synergistic strategy combining Cu pre-oxidation with hydrogen-free precursor chemistry. The combined strategy yields high-quality continuous R2R monolayer graphene, with monolayer coverage > 90% and ID/IG < 5% at 1 m/min, and ~80% monolayer with ID/IG ~20% at 2 m/min. This work establishes a scalable route to meter-per-minute graphene production by decoupling the constraints on growth mode, defect suppression, and carbon delivery.
- 3 July 2026
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 9 (28) , 13648
Correction to “Gradient-Reduced Graphene Oxide Aerogel with UltraBroadband Absorption from Microwave to Terahertz Bands”
- 3 July 2026
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 9 (28) , 13648
Correction to “Gradient-Reduced Graphene Oxide Aerogel with UltraBroadband Absorption from Microwave to Terahertz Bands”
- Open Access
- 1 May 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3243 (1)
Correlation Between Crystallinity and Transfer Integrity of CVD Graphene
Chemical vapor deposition (CVD) on copper substrates has emerged as a promising method for synthesizing large-area graphene films with controllable crystallographic orientation. However, variations in the crystalline structure of the copper substrate can significantly affect the growth behavior of graphene and its integrity after transfer. To investigate this effect, a series of CVD growth and transfer experiments were conducted on single-crystal and polycrystalline copper foils. In this paper, the crystallographic orientation, grain boundary distribution, and surface morphology of the copper substrates were characterized by scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). Raman spectroscopy was used to evaluate the defect density, strain distribution, and carrier doping level of graphene films both before and after transfer. The results show that single-crystal copper foils promote the growth of highly oriented graphene with low defect density. Nevertheless, the large, continuous domains formed on these substrates are more susceptible to stress concentration during transfer, leading to reduced film continuity. In contrast, graphene grown on polycrystalline copper exhibits higher defect density and random orientations, yet the abundant grain boundaries can facilitate stress relaxation, and help preserve to maintain overall film integrity after transfer. This study highlights the interplay between substrate crystallinity, graphene orientation, and transfer-induced stress, providing insights for optimizing single-crystal graphene transfer processes to balance orientation uniformity with membrane completeness.
- 1 May 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3243 (1)
Open AccessCorrelation Between Crystallinity and Transfer Integrity of CVD Graphene
Chemical vapor deposition (CVD) on copper substrates has emerged as a promising method for synthesizing large-area graphene films with controllable crystallographic orientation. However, variations in the crystalline structure of the copper substrate can significantly affect the growth behavior of graphene and its integrity after transfer. To investigate this effect, a series of CVD growth and transfer experiments were conducted on single-crystal and polycrystalline copper foils. In this paper, the crystallographic orientation, grain boundary distribution, and surface morphology of the copper substrates were characterized by scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). Raman spectroscopy was used to evaluate the defect density, strain distribution, and carrier doping level of graphene films both before and after transfer. The results show that single-crystal copper foils promote the growth of highly oriented graphene with low defect density. Nevertheless, the large, continuous domains formed on these substrates are more susceptible to stress concentration during transfer, leading to reduced film continuity. In contrast, graphene grown on polycrystalline copper exhibits higher defect density and random orientations, yet the abundant grain boundaries can facilitate stress relaxation, and help preserve to maintain overall film integrity after transfer. This study highlights the interplay between substrate crystallinity, graphene orientation, and transfer-induced stress, providing insights for optimizing single-crystal graphene transfer processes to balance orientation uniformity with membrane completeness.
- 1 May 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
Automation-Compatible Graphene Transfer Enabled by a Reinforced-Concrete Inspired Mesh-Vaseline Support Film
The growth of graphene on Cu via chemical vapor deposition has been well established for producing large-area high-quality graphene films, with subsequent transfer to target substrates being an essential step for most applications. While various transfer techniques have been explored, true industrial adoption remains limited. This is primarily because the strong adhesion between graphene and its growth substrate makes it difficult to maintain film integrity by mechanical peeling methods, though they are compatible with industrial operation. Conversely, traditional chemical etching methods, while preserving integrity, rely on highly flexible carrier films to ensure conformal contact with the target substrate. This required flexibility renders the films fragile and difficult to handle, posing a significant challenge for automation and spatial alignment. Here, we report a mesh-embedded Vaseline structure, inspired by reinforced concrete, as a robust carrier film for graphene transfer. The Vaseline acts as an adhesive layer, ensuring conformal contact to preserve graphene's integrity, while also being easily removable. The embedded mesh provides a self-supporting framework, enabling straightforward handling and compatibility with industrial automation. We demonstrate successful graphene transfer onto SiO2/Si wafers and curved surfaces with excellent integrity and cleanliness, and present a semiautomated transfer production line. Leveraging the precise spatial control afforded by the self-supporting carrier film, we further achieve, for the first time in a wet-transfer process, the fabrication of bilayer graphene with precisely controlled twist angles using CVD-grown domains, a capability previously accessible only through small-area manual assembly techniques. This work highlights the potential for scalable mass production and extends readily to other two-dimensional materials such as hexagonal boron nitride. By transforming the transfer process from handling fragile, floating films to manipulating a robust, self-supporting composite, our method bridges the gap between lab-scale demonstration and industry-scale automation.
- 1 May 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
Automation-Compatible Graphene Transfer Enabled by a Reinforced-Concrete Inspired Mesh-Vaseline Support Film
The growth of graphene on Cu via chemical vapor deposition has been well established for producing large-area high-quality graphene films, with subsequent transfer to target substrates being an essential step for most applications. While various transfer techniques have been explored, true industrial adoption remains limited. This is primarily because the strong adhesion between graphene and its growth substrate makes it difficult to maintain film integrity by mechanical peeling methods, though they are compatible with industrial operation. Conversely, traditional chemical etching methods, while preserving integrity, rely on highly flexible carrier films to ensure conformal contact with the target substrate. This required flexibility renders the films fragile and difficult to handle, posing a significant challenge for automation and spatial alignment. Here, we report a mesh-embedded Vaseline structure, inspired by reinforced concrete, as a robust carrier film for graphene transfer. The Vaseline acts as an adhesive layer, ensuring conformal contact to preserve graphene's integrity, while also being easily removable. The embedded mesh provides a self-supporting framework, enabling straightforward handling and compatibility with industrial automation. We demonstrate successful graphene transfer onto SiO2/Si wafers and curved surfaces with excellent integrity and cleanliness, and present a semiautomated transfer production line. Leveraging the precise spatial control afforded by the self-supporting carrier film, we further achieve, for the first time in a wet-transfer process, the fabrication of bilayer graphene with precisely controlled twist angles using CVD-grown domains, a capability previously accessible only through small-area manual assembly techniques. This work highlights the potential for scalable mass production and extends readily to other two-dimensional materials such as hexagonal boron nitride. By transforming the transfer process from handling fragile, floating films to manipulating a robust, self-supporting composite, our method bridges the gap between lab-scale demonstration and industry-scale automation.
- 23 April 2026
- Published by Springer Nature in Science China Technological Sciences
- Vol. 69 (5) , 1520207
Industrial-scale roll-to-roll graphene fabrication: Nucleation control for high-speed, low-defect growth at atmospheric pressure
- 23 April 2026
- Published by Springer Nature in Science China Technological Sciences
- Vol. 69 (5) , 1520207
Industrial-scale roll-to-roll graphene fabrication: Nucleation control for high-speed, low-defect growth at atmospheric pressure
- 2 March 2026
- Published by Springer Nature in Science China Materials
- Vol. 69 (6) , 3472-3480
Isotope-engineered hexagonal boron nitride films synthesized by plasma-enhanced chemical vapor deposition method from elemental boron and nitrogen precursors
- 2 March 2026
- Published by Springer Nature in Science China Materials
- Vol. 69 (6) , 3472-3480
Isotope-engineered hexagonal boron nitride films synthesized by plasma-enhanced chemical vapor deposition method from elemental boron and nitrogen precursors
- 16 February 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (7) , 11764-11773
Layer-Dependent Thermal Conductivity of Graphene toward Thermal Management Applications
Graphene has attracted considerable attention due to its exceptional thermal properties and potential applications in advanced thermal management systems. As the number of graphene layers increases, the cross-sectional area available for heat flow grows while the intrinsic in-plane thermal conductivity of each layer decreases because of enhanced interlayer scattering. The competing factors between the number of conducting channels and their interaction make understanding graphene's layer-dependent thermal conductivity essential for optimizing the thermal performance of graphene-based devices. In this study, the thermal conductivity of graphene with different layer numbers was measured by using a nanoscale thermal bridge method. Monolayer graphene exhibited a thermal conductivity up to 3100 W/m K, while the thermal conductivity further declined with layer number and stabilized beyond four layers. By evaluating the effective heat dissipation capability, a nonmonotonic dependence on graphene layer number was identified, with a critical regime appearing between 2 and 6 layers. The behavior was explained by a dual-path transport model, where both phononic and electronic heat carriers are considered. This layer-dependent reduction in thermal conductivity was attributed to phonon transport with an electronic heat-transport channel alongside. These findings provide insights into layer-dependent heat transfer in graphene and offer guidance for graphene-based thermal management and thermal design.
- 16 February 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (7) , 11764-11773
Layer-Dependent Thermal Conductivity of Graphene toward Thermal Management Applications
Graphene has attracted considerable attention due to its exceptional thermal properties and potential applications in advanced thermal management systems. As the number of graphene layers increases, the cross-sectional area available for heat flow grows while the intrinsic in-plane thermal conductivity of each layer decreases because of enhanced interlayer scattering. The competing factors between the number of conducting channels and their interaction make understanding graphene's layer-dependent thermal conductivity essential for optimizing the thermal performance of graphene-based devices. In this study, the thermal conductivity of graphene with different layer numbers was measured by using a nanoscale thermal bridge method. Monolayer graphene exhibited a thermal conductivity up to 3100 W/m K, while the thermal conductivity further declined with layer number and stabilized beyond four layers. By evaluating the effective heat dissipation capability, a nonmonotonic dependence on graphene layer number was identified, with a critical regime appearing between 2 and 6 layers. The behavior was explained by a dual-path transport model, where both phononic and electronic heat carriers are considered. This layer-dependent reduction in thermal conductivity was attributed to phonon transport with an electronic heat-transport channel alongside. These findings provide insights into layer-dependent heat transfer in graphene and offer guidance for graphene-based thermal management and thermal design.
- 23 May 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (22) , 32782-32789
Harnessing Graphene Plasmons by Accessing the Retardation Regime
Plasmons in graphene are highly tunable, mainly by leveraging the carrier density and Drude scattering. Here, we introduce another scheme, i.e., accessing the retardation regime (originated from the finite speed of light), to engineer the lifetime and dispersion of plasmons in graphene in the terahertz regime. We find that the retardation regime can be approached by reducing plasmon momentum in artificially stacked multilayer graphene systems with large Drude weight, and this can significantly increase the plasmon lifetime. In addition, an explicit theoretical model along with finite-element simulation was given, consistent with the experimental findings. Our work opens another avenue to manipulate terahertz plasmons in graphene.
- 23 May 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (22) , 32782-32789
Harnessing Graphene Plasmons by Accessing the Retardation Regime
Plasmons in graphene are highly tunable, mainly by leveraging the carrier density and Drude scattering. Here, we introduce another scheme, i.e., accessing the retardation regime (originated from the finite speed of light), to engineer the lifetime and dispersion of plasmons in graphene in the terahertz regime. We find that the retardation regime can be approached by reducing plasmon momentum in artificially stacked multilayer graphene systems with large Drude weight, and this can significantly increase the plasmon lifetime. In addition, an explicit theoretical model along with finite-element simulation was given, consistent with the experimental findings. Our work opens another avenue to manipulate terahertz plasmons in graphene.