Elham Jalilnejad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Elham Jalilnejad has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Adolfo Iulianelli
Institute of Membrane Technology of the National Research Council (CNR-ITM), Via P. Bucci 17C, 87036 Rende, Italy
3 shared publications Mehran Nalband
3 shared publications- Kamran Ghasemzadeh
Faculty of Chemical Engineering, Urmia University of Technology, Urmia 57166-93187, Iran
2 shared publications Afshin Amani
1 shared publication- Alireza Habibi
Faculty of Chemical and Petroleum Engineering, Razi University, Kermanshah, Iran
1 shared publication - Angelo Basile
Hydrogenia S.r.l., Via Roma, n. 8/2, 16121 Genoa, Italy
1 shared publication
Latest Publications
- Open Access
Performance Analysis of Silica Fluidized Bed Membrane Reactor for Hydrogen Production as a Green Process Using CFD Modelling
The main aim of this study deals with the potential evaluation of a fluidized bed membrane reactor (FBMR) for hydrogen production as a clean fuel carrier via methanol steam reforming reaction, comparing its performance with other reactors including packed bed membrane reactors (PBMR), fluidized bed reactors (FBR), and packed bed reactors (PBR). For this purpose, a two-dimensional, axisymmetric numerical model was developed using computational fluid dynamics (CFD) to simulate the reactor performances. Model accuracy was validated by comparing the simulation results for PBMR and PB with experimental data, showing an accurate agreement within them. The model was then employed to examine the effects of key operating parameters, including reaction temperature, pressure, steam-to-methanol molar ratio, and gas volumetric space velocity, on reactor performance in terms of methanol conversion, hydrogen yield, hydrogen recovery, and selectivity. At 573 K, 1 bar, a feed molar ratio of 3/1, and a space velocity of 9000 h−1, the PBMR reached the best results in terms of methanol conversion, hydrogen yield, hydrogen recovery, and hydrogen selectivity, such as 67.6%, 69.5%, 14.9%, and 97.1%, respectively. On the other hand, the FBMR demonstrated superior performance with respect to the latter reaching a methanol conversion of 98.3%, hydrogen yield of 95.8%, hydrogen recovery of 74.5%, and hydrogen selectivity of 97.4%. These findings indicate that the FBMR offers significantly better performance than the other reactor types studied in this work, making it a highly efficient method for hydrogen production through methanol steam reforming, and a promising pathway for clean energy generation.
Open AccessPerformance Analysis of Silica Fluidized Bed Membrane Reactor for Hydrogen Production as a Green Process Using CFD Modelling
The main aim of this study deals with the potential evaluation of a fluidized bed membrane reactor (FBMR) for hydrogen production as a clean fuel carrier via methanol steam reforming reaction, comparing its performance with other reactors including packed bed membrane reactors (PBMR), fluidized bed reactors (FBR), and packed bed reactors (PBR). For this purpose, a two-dimensional, axisymmetric numerical model was developed using computational fluid dynamics (CFD) to simulate the reactor performances. Model accuracy was validated by comparing the simulation results for PBMR and PB with experimental data, showing an accurate agreement within them. The model was then employed to examine the effects of key operating parameters, including reaction temperature, pressure, steam-to-methanol molar ratio, and gas volumetric space velocity, on reactor performance in terms of methanol conversion, hydrogen yield, hydrogen recovery, and selectivity. At 573 K, 1 bar, a feed molar ratio of 3/1, and a space velocity of 9000 h−1, the PBMR reached the best results in terms of methanol conversion, hydrogen yield, hydrogen recovery, and hydrogen selectivity, such as 67.6%, 69.5%, 14.9%, and 97.1%, respectively. On the other hand, the FBMR demonstrated superior performance with respect to the latter reaching a methanol conversion of 98.3%, hydrogen yield of 95.8%, hydrogen recovery of 74.5%, and hydrogen selectivity of 97.4%. These findings indicate that the FBMR offers significantly better performance than the other reactor types studied in this work, making it a highly efficient method for hydrogen production through methanol steam reforming, and a promising pathway for clean energy generation.
- Open Access
- 28 December 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-15
Synthesis, characterization, experimental design and process analysis of heavy metals adsorption on a wheat straw based amidoximated bioadsorbent
In this research, 3-(trimethoxysilyl)propyl methacrylate (MPS) silane agent was applied to modify the extracted wheat straw (WS) cellulose as a natural biopolymer. Polyacrylonitrile (PAN) was attached to the MPS-modified WS (MPS-WS) via in-situ polymerization to form PAN-WS biocomposite. AO-WS amidoximated biocomposite adsorbent was synthesized through amidoxime reaction and the effects of different parameters including agitation speed, metal ion concentration, and adsorbent dosage on its efficiency of Pb(II) removal were investigated using the Taguchi experimental design method. The adsorbent was characterized using FE-SEM, FTIR, XRD, and TGA. The FTIR results confirmed that the alkaline treatment removed the hemicellulose and lignin groups and that the silane agent successfully bonded to the WS cellulose. The thermal stability of WS was enhanced by the MPS-WS composite due to the attachment of acrylonitrile polymer chains. The ANOVA results indicated that increasing the adsorbent dosage and decreasing the pollutant’s initial concentration significantly improved the adsorption efficiency. The optimal conditions (an agitation speed = 400 rpm, C0 = 60 mg/L, an adsorbent amount = 0.1 g) yielded maximum adsorption capacity of 22.26 mg/g for the AO-WS bioadsorbent. The kinetic and isotherm studies revealed that the pseudo-second-order kinetic model and the Dubinin-Radushkevich isotherm fit the experimental data best.
- 28 December 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-15
Open AccessSynthesis, characterization, experimental design and process analysis of heavy metals adsorption on a wheat straw based amidoximated bioadsorbent
In this research, 3-(trimethoxysilyl)propyl methacrylate (MPS) silane agent was applied to modify the extracted wheat straw (WS) cellulose as a natural biopolymer. Polyacrylonitrile (PAN) was attached to the MPS-modified WS (MPS-WS) via in-situ polymerization to form PAN-WS biocomposite. AO-WS amidoximated biocomposite adsorbent was synthesized through amidoxime reaction and the effects of different parameters including agitation speed, metal ion concentration, and adsorbent dosage on its efficiency of Pb(II) removal were investigated using the Taguchi experimental design method. The adsorbent was characterized using FE-SEM, FTIR, XRD, and TGA. The FTIR results confirmed that the alkaline treatment removed the hemicellulose and lignin groups and that the silane agent successfully bonded to the WS cellulose. The thermal stability of WS was enhanced by the MPS-WS composite due to the attachment of acrylonitrile polymer chains. The ANOVA results indicated that increasing the adsorbent dosage and decreasing the pollutant’s initial concentration significantly improved the adsorption efficiency. The optimal conditions (an agitation speed = 400 rpm, C0 = 60 mg/L, an adsorbent amount = 0.1 g) yielded maximum adsorption capacity of 22.26 mg/g for the AO-WS bioadsorbent. The kinetic and isotherm studies revealed that the pseudo-second-order kinetic model and the Dubinin-Radushkevich isotherm fit the experimental data best.
- Open Access
- 16 February 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-16
Application of TOPSIS algorithm in describing bacterial cellulose-based composite hydrogel performance in incorporating methylene blue as a model drug
A multi-component hydrogel was developed using bacterial cellulose, alginate, and gelatin with the aid of glycerol as trihydric alcohol which participates in re-distribution of hydrogen bonds in the test system. FTIR, XRD, SEM, and TGA as instrumental techniques were used to structurally characterize the physical/chemical properties of the formed composite hydrogel. By using an exponential equation, swelling behavior of the hydrogel was evaluated. By incorporating a model drug (methylene blue—MB) in the formed hydrogel, experiments were directed to study release characteristics of the MB where the medium solution for the release was prepared at four different pHs. The maximum cumulative drug release at pH 2.8, 6, 7.4, and 9 were 42.8, 63, 80, and 84.5%, respectively. Data fitting process was carried out using five kinetic models (Korsmeyer-Peppas, Higuchi, Hopfenberg, zero-order, and first-order equations) and the preferred kinetic model at each pH was estimated by applying TOPSIS algorithmic technique. The adsorption capacity of the hydrogel in relation to MB was determined while thermodynamic properties of this relationship were quantified ( $$\Delta{\text{H}}_{\text{ad}}^{0}= \text{ } -\text{99.95 kJ} \, {\text{mo}}{\text{l}}^{-{1}}$$ and $$\Delta{\text{S}}_{\text{ad}}^{0}= -\text{0.237 kJ} \, {\text{mo}}{\text{l}}^{-{1}} {\text{K}}^{-{1}}$$ ). The results of the present study were in favor of the potential usage of the developed composite hydrogel in drug delivery systems.- 16 February 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-16
Open AccessApplication of TOPSIS algorithm in describing bacterial cellulose-based composite hydrogel performance in incorporating methylene blue as a model drug
A multi-component hydrogel was developed using bacterial cellulose, alginate, and gelatin with the aid of glycerol as trihydric alcohol which participates in re-distribution of hydrogen bonds in the test system. FTIR, XRD, SEM, and TGA as instrumental techniques were used to structurally characterize the physical/chemical properties of the formed composite hydrogel. By using an exponential equation, swelling behavior of the hydrogel was evaluated. By incorporating a model drug (methylene blue—MB) in the formed hydrogel, experiments were directed to study release characteristics of the MB where the medium solution for the release was prepared at four different pHs. The maximum cumulative drug release at pH 2.8, 6, 7.4, and 9 were 42.8, 63, 80, and 84.5%, respectively. Data fitting process was carried out using five kinetic models (Korsmeyer-Peppas, Higuchi, Hopfenberg, zero-order, and first-order equations) and the preferred kinetic model at each pH was estimated by applying TOPSIS algorithmic technique. The adsorption capacity of the hydrogel in relation to MB was determined while thermodynamic properties of this relationship were quantified ( $$\Delta{\text{H}}_{\text{ad}}^{0}= \text{ } -\text{99.95 kJ} \, {\text{mo}}{\text{l}}^{-{1}}$$ and $$\Delta{\text{S}}_{\text{ad}}^{0}= -\text{0.237 kJ} \, {\text{mo}}{\text{l}}^{-{1}} {\text{K}}^{-{1}}$$ ). The results of the present study were in favor of the potential usage of the developed composite hydrogel in drug delivery systems. - Open Access
Performance Comparison of Polymeric and Silica-Based Multi-Bed Pervaporation Membrane Reactors during Ethyl Levulinate Production
A detailed numerical study of ethyl levulinate (EtLA) production with levulinic acid (LA) and ethanol (Et) in a multi-bed traditional reactor (MB-TR) and a silica-based and polymeric multi-bed pervaporation membrane reactors (MB-PVMR) was conducted and the efficiency of each design was studied under different operation conditions. Due to water production in the EtLA production process, water removal by a pervaporation system may improve process performance. Our results showed that MB-PVMR had higher performance compared with MB-TR. In addition, the silica membrane was more effective in water removal compared with the polymeric membrane. Therefore, higher LA conversion was achievable by a silica-based multi-bed pervaporation membrane reactor (SMB-PVMR). All the results were evaluated for percentage of water removal and LA conversion, based on variations in the Et/LA molar ratio, feed molar flow, reaction zone temperature, and catalyst loading. The results showed that water removal was higher than 95% and LA conversion of about 95% was attained by SMB-PVMR.
Open AccessPerformance Comparison of Polymeric and Silica-Based Multi-Bed Pervaporation Membrane Reactors during Ethyl Levulinate Production
A detailed numerical study of ethyl levulinate (EtLA) production with levulinic acid (LA) and ethanol (Et) in a multi-bed traditional reactor (MB-TR) and a silica-based and polymeric multi-bed pervaporation membrane reactors (MB-PVMR) was conducted and the efficiency of each design was studied under different operation conditions. Due to water production in the EtLA production process, water removal by a pervaporation system may improve process performance. Our results showed that MB-PVMR had higher performance compared with MB-TR. In addition, the silica membrane was more effective in water removal compared with the polymeric membrane. Therefore, higher LA conversion was achievable by a silica-based multi-bed pervaporation membrane reactor (SMB-PVMR). All the results were evaluated for percentage of water removal and LA conversion, based on variations in the Et/LA molar ratio, feed molar flow, reaction zone temperature, and catalyst loading. The results showed that water removal was higher than 95% and LA conversion of about 95% was attained by SMB-PVMR.
- Open Access
A Theoretical Analysis on a Multi-Bed Pervaporation Membrane Reactor during Levulinic Acid Esterification Using the Computational Fluid Dynamic Method
Pervaporation is a peculiar membrane separation process, which is considered for integration with a variety of reactions in promising new applications. Pervaporation membrane reactors have some specific uses in sustainable chemistry, such as the esterification processes. This theoretical study based on the computational fluid dynamics method aims to evaluate the performance of a multi-bed pervaporation membrane reactor (including poly (vinyl alcohol) membrane) to produce ethyl levulinate as a significant fuel additive, coming from the esterification of levulinic acid. For comparison, an equivalent multi-bed traditional reactor is also studied at the same operating conditions of the aforementioned pervaporation membrane reactor. A computational fluid dynamics model was developed and validated by experimental literature data. The effects of reaction temperature, catalyst loading, feed molar ratio, and feed flow rate on the reactor’s performance in terms of levulinic acid conversion and water removal were hence studied. The simulations indicated that the multi-bed pervaporation membrane reactor results to be the best solution over the multi-bed traditional reactor, presenting the best simulation results at 343 K, 2 bar, catalyst loading 8.6 g, feed flow rate 7 mm3/s, and feed molar ratio 3 with levulinic acid conversion equal to 95.3% and 91.1% water removal.
Open AccessA Theoretical Analysis on a Multi-Bed Pervaporation Membrane Reactor during Levulinic Acid Esterification Using the Computational Fluid Dynamic Method
Pervaporation is a peculiar membrane separation process, which is considered for integration with a variety of reactions in promising new applications. Pervaporation membrane reactors have some specific uses in sustainable chemistry, such as the esterification processes. This theoretical study based on the computational fluid dynamics method aims to evaluate the performance of a multi-bed pervaporation membrane reactor (including poly (vinyl alcohol) membrane) to produce ethyl levulinate as a significant fuel additive, coming from the esterification of levulinic acid. For comparison, an equivalent multi-bed traditional reactor is also studied at the same operating conditions of the aforementioned pervaporation membrane reactor. A computational fluid dynamics model was developed and validated by experimental literature data. The effects of reaction temperature, catalyst loading, feed molar ratio, and feed flow rate on the reactor’s performance in terms of levulinic acid conversion and water removal were hence studied. The simulations indicated that the multi-bed pervaporation membrane reactor results to be the best solution over the multi-bed traditional reactor, presenting the best simulation results at 343 K, 2 bar, catalyst loading 8.6 g, feed flow rate 7 mm3/s, and feed molar ratio 3 with levulinic acid conversion equal to 95.3% and 91.1% water removal.
- 1 August 2020
- Published by Elsevier in Particuology
- Vol. 51, 91-108
Hydrodynamic behavior of an airlift reactor with net draft tube with different configurations: Numerical evaluation using CFD technique
- 1 August 2020
- Published by Elsevier in Particuology
- Vol. 51, 91-108
Hydrodynamic behavior of an airlift reactor with net draft tube with different configurations: Numerical evaluation using CFD technique
- 11 September 2019
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 17 (12)
3D CFD Simulation of Gas Hold-up and Mass Transfer in a Modified Airlift Reactor with Net Draft Tube
This paper documents CFD simulations of the gas hold-up (ɛg) and volumetric mass transfer coefficient (KLa) for three kinds of airlift reactors (ALRs) namely, conventional ALR, ALR with net draft tube (ALR-ndt), and packed-bed ALR with net draft tube (PBALR-ndt). The 3D two-fluid Eulerian-Eulerian model was adopted to predict the influence of superficial gas velocity on ɛgand KLa. The simulation results were consistent with the trends described previously in the experimental work regarding ɛgand KLa values and a good agreement was obtained (absolute error less than 20 %). Based on the simulation results, axial flow is the dominant flow in the conventional ALR while in ALR-ndt and PBALR-ndt radial flow streamlines are appeared in the reactors due to the presence of concentric net draft tube which improves their performance. The effective role of the net draft tube is proven since consequence of generation of small bubbles by passing through net draft tube is the entrainment of a larger percentage of gas bubbles from the riser into the downcomer which results in improvement of gas holdup and the KLa values. An exponential correlation is used for relating gas hold-up and mass transfer coefficient. Higher power obtained for ALR-ndt and PBALR-ndt (n ≈ 1.22) compared to ALR (n = 0.95) was indicative of high sensitivity of KLa value to gas hold-up in these reactors due to presence of the concentric net draft tube. The CFD modeling is considered to be an invaluable tool allowing us to analyze and visualize the impact of fluidic forces on hydrodynamic properties and consequently, reactor performance.
- 11 September 2019
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 17 (12)
3D CFD Simulation of Gas Hold-up and Mass Transfer in a Modified Airlift Reactor with Net Draft Tube
This paper documents CFD simulations of the gas hold-up (ɛg) and volumetric mass transfer coefficient (KLa) for three kinds of airlift reactors (ALRs) namely, conventional ALR, ALR with net draft tube (ALR-ndt), and packed-bed ALR with net draft tube (PBALR-ndt). The 3D two-fluid Eulerian-Eulerian model was adopted to predict the influence of superficial gas velocity on ɛgand KLa. The simulation results were consistent with the trends described previously in the experimental work regarding ɛgand KLa values and a good agreement was obtained (absolute error less than 20 %). Based on the simulation results, axial flow is the dominant flow in the conventional ALR while in ALR-ndt and PBALR-ndt radial flow streamlines are appeared in the reactors due to the presence of concentric net draft tube which improves their performance. The effective role of the net draft tube is proven since consequence of generation of small bubbles by passing through net draft tube is the entrainment of a larger percentage of gas bubbles from the riser into the downcomer which results in improvement of gas holdup and the KLa values. An exponential correlation is used for relating gas hold-up and mass transfer coefficient. Higher power obtained for ALR-ndt and PBALR-ndt (n ≈ 1.22) compared to ALR (n = 0.95) was indicative of high sensitivity of KLa value to gas hold-up in these reactors due to presence of the concentric net draft tube. The CFD modeling is considered to be an invaluable tool allowing us to analyze and visualize the impact of fluidic forces on hydrodynamic properties and consequently, reactor performance.
- Open Access
Recent Progresses in Application of Membrane Bioreactors in Production of Biohydrogen
Biohydrogen is a clean and viable energy carrier generated through various green and renewable energy sources such as biomass. This review focused on the application of membrane bioreactors (MBRs), emphasizing the combination of these devices with biological processes, for bio-derived hydrogen production. Direct biophotolysis, indirect biophotolysis, photo-fermentation, dark fermentation, and conventional techniques are discussed as the common methods of biohydrogen production. The anaerobic process membrane bioreactors (AnMBRs) technology is presented and discussed as a preferable choice for producing biohydrogen due to its low cost and the ability of overcoming problems posed by carbon emissions. General features of AnMBRs and operational parameters are comprehensively overviewed. Although MBRs are being used as a well-established and mature technology with many full-scale plants around the world, membrane fouling still remains a serious obstacle and a future challenge. Therefore, this review highlights the main benefits and drawbacks of MBRs application, also discussing the comparison between organic and inorganic membranes utilization to determine which may constitute the best solution for providing pure hydrogen. Nevertheless, research is still needed to overcome remaining barriers to practical applications such as low yields and production rates, and to identify biohydrogen as one of the most appealing renewable energies in the future.
Open AccessRecent Progresses in Application of Membrane Bioreactors in Production of Biohydrogen
Biohydrogen is a clean and viable energy carrier generated through various green and renewable energy sources such as biomass. This review focused on the application of membrane bioreactors (MBRs), emphasizing the combination of these devices with biological processes, for bio-derived hydrogen production. Direct biophotolysis, indirect biophotolysis, photo-fermentation, dark fermentation, and conventional techniques are discussed as the common methods of biohydrogen production. The anaerobic process membrane bioreactors (AnMBRs) technology is presented and discussed as a preferable choice for producing biohydrogen due to its low cost and the ability of overcoming problems posed by carbon emissions. General features of AnMBRs and operational parameters are comprehensively overviewed. Although MBRs are being used as a well-established and mature technology with many full-scale plants around the world, membrane fouling still remains a serious obstacle and a future challenge. Therefore, this review highlights the main benefits and drawbacks of MBRs application, also discussing the comparison between organic and inorganic membranes utilization to determine which may constitute the best solution for providing pure hydrogen. Nevertheless, research is still needed to overcome remaining barriers to practical applications such as low yields and production rates, and to identify biohydrogen as one of the most appealing renewable energies in the future.
- 11 December 2018
- Published by Springer Nature in Bioprocess and Biosystems Engineering
- Vol. 42 (3) , 485-497
Experimentation and CFD modeling of continuous degradation of formaldehyde by immobilized Ralstonia eutropha in a semi-pilot-scale plug flow bioreactor
This study focuses on continuous formaldehyde (FA) biodegradation by Ralstonia eutropha immobilized on polyurethane foam in a semi-pilot-scale plug flow packed-bed bioreactor. The stepwise increasing of the influent FA concentration from 43.9 to 1325.1 mg L−1 was studied in the bioreactor during 70 days of operation. A complete removal of FA was achieved for inlet concentration up to 425.5 mg L−1 and the initial specific biodegradation rate reached to its maximum value about 44.3 mg gcell−1 h−1 at 425.5 mg L−1. However, further increase of inlet concentration resulted in decrease of the biodegradation performance of the immobilized cells due to the inhibitory effect of FA on the enzymatic system involved in the biodegradation process. Based on kinetic modeling results, the Luong equation with the following constants could best describe the behavior of the bio-system: maximum specific FA biodegradation rate (qmax) of 124 mg gcell−1 h−1, half-saturation constant (KS) of 337.2 mg L−1, maximum degradable FA concentration (Smax) of 1582 mg L−1, and shape factor (n) of 1.49. Also, three-dimensional simulation of the bioreactor was performed using an integrated computational fluid dynamics (CFD) approach that takes into account both the biokinetic constants of the immobilized system as well as the fluid properties under steady-state condition. Eulerian computations successfully anticipated the concentration gradients through the reactor for different inlet FA concentrations, and uniform vertical velocity pathlines and non-dispersed plug flow inside the reactor were verified by the presented velocity distribution and flow streamlines.
- 11 December 2018
- Published by Springer Nature in Bioprocess and Biosystems Engineering
- Vol. 42 (3) , 485-497
Experimentation and CFD modeling of continuous degradation of formaldehyde by immobilized Ralstonia eutropha in a semi-pilot-scale plug flow bioreactor
This study focuses on continuous formaldehyde (FA) biodegradation by Ralstonia eutropha immobilized on polyurethane foam in a semi-pilot-scale plug flow packed-bed bioreactor. The stepwise increasing of the influent FA concentration from 43.9 to 1325.1 mg L−1 was studied in the bioreactor during 70 days of operation. A complete removal of FA was achieved for inlet concentration up to 425.5 mg L−1 and the initial specific biodegradation rate reached to its maximum value about 44.3 mg gcell−1 h−1 at 425.5 mg L−1. However, further increase of inlet concentration resulted in decrease of the biodegradation performance of the immobilized cells due to the inhibitory effect of FA on the enzymatic system involved in the biodegradation process. Based on kinetic modeling results, the Luong equation with the following constants could best describe the behavior of the bio-system: maximum specific FA biodegradation rate (qmax) of 124 mg gcell−1 h−1, half-saturation constant (KS) of 337.2 mg L−1, maximum degradable FA concentration (Smax) of 1582 mg L−1, and shape factor (n) of 1.49. Also, three-dimensional simulation of the bioreactor was performed using an integrated computational fluid dynamics (CFD) approach that takes into account both the biokinetic constants of the immobilized system as well as the fluid properties under steady-state condition. Eulerian computations successfully anticipated the concentration gradients through the reactor for different inlet FA concentrations, and uniform vertical velocity pathlines and non-dispersed plug flow inside the reactor were verified by the presented velocity distribution and flow streamlines.
- 25 May 2018
- Published by Taylor & Francis in Chemical Engineering Communications
- Vol. 205 (11) , 1537-1554
Fixed-bed column performance of methylene blue biosorption byLuffa cylindrica: statistical and mathematical modeling
This study aimed to investigate the adsorption capacity of Iranian Luffa cylindrica as a natural lignocellulosic adsorbent for biosorption of methylene blue (MB) using a fixed-bed column. The response surface methodology based on central composite design was used to evaluate the interactive effects of three major operating parameters (inlet MB concentration, Luffa dosage, and feed flow rate) on the dye removal percentage (response variable). The significance of the proposed quadratic model was validated by a high coefficient of determination (R2 = 0.995) and a low p value (−1, Luffa dosage 2.78 g, and feed flow rate 5 mL min−1, and the maximum MB removal efficiency was founded to be 51% (qmax = 21.4 mg g−1) at optimum conditions. The breakthrough curves were predicted by the Adams–Bohart and Thomas models using nonlinear regression analysis, whereas the experimental data fitted well with the Thomas model (R2 ≈ 0.96–0.98). Further surface modification studies enabled us to achieve the maximum MB removal efficiency of 77% (qmax = 46.58 mg g−1) with NaOH-modified Luffa, which is attributed to the intensification of the negatively charged surface of the base-modified adsorbent with hydroxyl groups. The nature of biosorbent–dye interactions was also evaluated by FTIR analysis. The highest desorption performance of MB from Luffa fibers was obtained with HCl solution reaching a desorbed amount of qdes = 130.5 mg in the column studies. The ion exchange is introduced as the dominant biosorption mechanism of MB onto Luffa fibers in this study.
- 25 May 2018
- Published by Taylor & Francis in Chemical Engineering Communications
- Vol. 205 (11) , 1537-1554
Fixed-bed column performance of methylene blue biosorption byLuffa cylindrica: statistical and mathematical modeling
This study aimed to investigate the adsorption capacity of Iranian Luffa cylindrica as a natural lignocellulosic adsorbent for biosorption of methylene blue (MB) using a fixed-bed column. The response surface methodology based on central composite design was used to evaluate the interactive effects of three major operating parameters (inlet MB concentration, Luffa dosage, and feed flow rate) on the dye removal percentage (response variable). The significance of the proposed quadratic model was validated by a high coefficient of determination (R2 = 0.995) and a low p value (−1, Luffa dosage 2.78 g, and feed flow rate 5 mL min−1, and the maximum MB removal efficiency was founded to be 51% (qmax = 21.4 mg g−1) at optimum conditions. The breakthrough curves were predicted by the Adams–Bohart and Thomas models using nonlinear regression analysis, whereas the experimental data fitted well with the Thomas model (R2 ≈ 0.96–0.98). Further surface modification studies enabled us to achieve the maximum MB removal efficiency of 77% (qmax = 46.58 mg g−1) with NaOH-modified Luffa, which is attributed to the intensification of the negatively charged surface of the base-modified adsorbent with hydroxyl groups. The nature of biosorbent–dye interactions was also evaluated by FTIR analysis. The highest desorption performance of MB from Luffa fibers was obtained with HCl solution reaching a desorbed amount of qdes = 130.5 mg in the column studies. The ion exchange is introduced as the dominant biosorption mechanism of MB onto Luffa fibers in this study.