Jessica M. Andriolo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jessica M. Andriolo has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
Jack L. Skinner
7 shared publications- Amos Taiswa
Department of Mechanical Engineering, Montana Technological University, 1300 W Park St, Butte, Montana 59701, United States
2 shared publications - Erik M. Grumstrup
Montana State University
2 shared publications - Jack L. Skinner
Montana Tech Nanotechnology Laboratory, Montana Technological University, Butte, USA
2 shared publications McKenzie L. Joseph
Montana Tech Nanotechnology Laboratory, Montana Technological University 2 , Butte, Montana 59701
2 shared publicationsAmos Taiswa
1 shared publication
Latest Publications
- 3 February 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 43 (2)
Photoluminescence lifetime of perovskites on modified substrates
Lead halide perovskites have gained attention for their potential in optoelectronic applications, including photovoltaics and light-emitting devices, due to their remarkable optical and electronic properties. However, performance of these materials is highly dependent on morphological properties of the underlying substrates. In this study, the effects of substrate modifications on the photoluminescence lifetimes of CsPbBr₃ perovskites deposited on TiO2 substrates that were annealed at various temperatures were investigated. TiO2 substrates were characterized using glancing-angle x-ray diffraction and spectroscopic ellipsometry to assess changes in crystallinity and surface roughness. Time-correlated single photon counting spectroscopy was employed to measure the photoluminescent lifetimes of the perovskites. Scanning electron microscopy and x-ray diffraction were used to determine morphology and crystallinity. Results show a clear relationship between substrate annealing temperature and the photoluminescent lifetime of perovskite microcrystals. Substrates annealed at temperatures below 300 °C exhibited increased surface roughness with increased annealing temperature (22.4 Ȧ at room temperature and 48.05 Ȧ at 300 °C) and correspondingly shorter photoluminescent lifetimes (3.5 ns at room temperature and 0.4 ns at 300 °C) suggesting more rapid charge carrier recombination. In contrast, substrates annealed at 350 °C exhibited the longest lifetimes at 4.19 ns indicating a decrease in trap-mediated nonradiative recombination. Substrates annealed at 400 °C showed a further increase in crystallinity but did not extend the lifetime beyond that seen at 350 °C, suggesting an optimal balance between surface roughness and crystallization. These findings provide insights into the role of morphological substrate modifications in optimizing the optoelectronic properties of perovskite materials.
- 3 February 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 43 (2)
Photoluminescence lifetime of perovskites on modified substrates
Lead halide perovskites have gained attention for their potential in optoelectronic applications, including photovoltaics and light-emitting devices, due to their remarkable optical and electronic properties. However, performance of these materials is highly dependent on morphological properties of the underlying substrates. In this study, the effects of substrate modifications on the photoluminescence lifetimes of CsPbBr₃ perovskites deposited on TiO2 substrates that were annealed at various temperatures were investigated. TiO2 substrates were characterized using glancing-angle x-ray diffraction and spectroscopic ellipsometry to assess changes in crystallinity and surface roughness. Time-correlated single photon counting spectroscopy was employed to measure the photoluminescent lifetimes of the perovskites. Scanning electron microscopy and x-ray diffraction were used to determine morphology and crystallinity. Results show a clear relationship between substrate annealing temperature and the photoluminescent lifetime of perovskite microcrystals. Substrates annealed at temperatures below 300 °C exhibited increased surface roughness with increased annealing temperature (22.4 Ȧ at room temperature and 48.05 Ȧ at 300 °C) and correspondingly shorter photoluminescent lifetimes (3.5 ns at room temperature and 0.4 ns at 300 °C) suggesting more rapid charge carrier recombination. In contrast, substrates annealed at 350 °C exhibited the longest lifetimes at 4.19 ns indicating a decrease in trap-mediated nonradiative recombination. Substrates annealed at 400 °C showed a further increase in crystallinity but did not extend the lifetime beyond that seen at 350 °C, suggesting an optimal balance between surface roughness and crystallization. These findings provide insights into the role of morphological substrate modifications in optimizing the optoelectronic properties of perovskite materials.
- Open Access
- 12 September 2024
- Published by Springer Nature in MRS Advances
- Vol. 9 (16) , 1284-1291
High strain rate behavior of polycaprolactone reinforced with aramid nanofiber for insight into dynamic behavior
Self-healing materials are repairable and extend product lifetimes but are limited in application due to their mechanical properties such as low yield strength. Here, we examined the dynamic mechanical performance of an elastomeric polymer composite containing aramid nanofibers. These studies provided an economically feasible foundation to understand the reinforcement concentration and resultant mechanical properties that would result should aramid nanofibers be used to reinforce a self-healing polymer that requires complex synthesis methods and expensive reactants. The elastomeric polymer used was polycaprolactone containing various weight percent aramid nanofibers. Dynamic mechanical testing of these samples was performed using a split-Hopkinson pressure bar system that enabled quantification of polymer softening and aramid nanofiber reinforcement. Dynamic flow stress and strain rates were also calculated with these data. Crystallinity and thermal softening effects of solvent dissolution of polycaprolactone are explored to further characterize the performance of aramid nanofibers as a fiber in composite materials. Graphical abstract
- 12 September 2024
- Published by Springer Nature in MRS Advances
- Vol. 9 (16) , 1284-1291
Open AccessHigh strain rate behavior of polycaprolactone reinforced with aramid nanofiber for insight into dynamic behavior
Self-healing materials are repairable and extend product lifetimes but are limited in application due to their mechanical properties such as low yield strength. Here, we examined the dynamic mechanical performance of an elastomeric polymer composite containing aramid nanofibers. These studies provided an economically feasible foundation to understand the reinforcement concentration and resultant mechanical properties that would result should aramid nanofibers be used to reinforce a self-healing polymer that requires complex synthesis methods and expensive reactants. The elastomeric polymer used was polycaprolactone containing various weight percent aramid nanofibers. Dynamic mechanical testing of these samples was performed using a split-Hopkinson pressure bar system that enabled quantification of polymer softening and aramid nanofiber reinforcement. Dynamic flow stress and strain rates were also calculated with these data. Crystallinity and thermal softening effects of solvent dissolution of polycaprolactone are explored to further characterize the performance of aramid nanofibers as a fiber in composite materials. Graphical abstract
- 23 August 2024
- Published by Elsevier in Biomass and Bioenergy
- Vol. 189
Role of solvent in selective hydrodeoxygenation of monomeric phenols
- 23 August 2024
- Published by Elsevier in Biomass and Bioenergy
- Vol. 189
Role of solvent in selective hydrodeoxygenation of monomeric phenols
- Open Access
- 6 June 2024
- Published by Springer Nature in Discover Nano
- Vol. 19 (1) , 1-11
Highly controlled multiplex electrospinning
Applications of electrospinning (ES) range from fabrication of biomedical devices and tissue regeneration scaffolds to light manipulation and energy conversion, and even to deposition of materials that act as growth platforms for nanoscale catalysis. One major limitation to wide adoption of ES is stochastic fiber deposition resulting from the chaotic motion of the polymer stream as is approaches the deposition surface. In the past, fabrication of structures or materials with precisely determined mesoscale morphology has been accomplished through modification of electrode shape, use of multi-dimensional electrodes or pins, deposition onto weaving looms, hand-held electrospinning devices that allow the user to guide deposition, or electric field manipulation by lensing elements or apertures. In this work, we demonstrate an ES system that contains multiple high voltage power supplies that are independently controlled through a control algorithm implemented in LabVIEW. The end result is what we term “multiplex ES” where multiple independently controlled high-voltage signals are combined by the ES fiber to result in unique deposition control. COMSOL Multiphysics® software was used to model the electric field produced in this novel ES system. Using the multi-power supply system, we demonstrate fabrication of woven fiber materials that do not require complex deposition surfaces. Time-varied sinusoidal wave inputs were used to create electrospun torus shapes. The outer diameter of the tori was found, through parametric analysis, to be rather insensitive to frequency used during deposition, while inner diameter was inversely related to frequency, resulting in overall width of the tori increasing with frequency. Multiplex ES has a high-frequency cutoff based on the time response of the high voltage electrical circuit. These time constants were measured and minimized through the addition of parallel resistors that decreased impedance of the system and improved the high-frequency cutoff by up to 63%.
- 6 June 2024
- Published by Springer Nature in Discover Nano
- Vol. 19 (1) , 1-11
Open AccessHighly controlled multiplex electrospinning
Applications of electrospinning (ES) range from fabrication of biomedical devices and tissue regeneration scaffolds to light manipulation and energy conversion, and even to deposition of materials that act as growth platforms for nanoscale catalysis. One major limitation to wide adoption of ES is stochastic fiber deposition resulting from the chaotic motion of the polymer stream as is approaches the deposition surface. In the past, fabrication of structures or materials with precisely determined mesoscale morphology has been accomplished through modification of electrode shape, use of multi-dimensional electrodes or pins, deposition onto weaving looms, hand-held electrospinning devices that allow the user to guide deposition, or electric field manipulation by lensing elements or apertures. In this work, we demonstrate an ES system that contains multiple high voltage power supplies that are independently controlled through a control algorithm implemented in LabVIEW. The end result is what we term “multiplex ES” where multiple independently controlled high-voltage signals are combined by the ES fiber to result in unique deposition control. COMSOL Multiphysics® software was used to model the electric field produced in this novel ES system. Using the multi-power supply system, we demonstrate fabrication of woven fiber materials that do not require complex deposition surfaces. Time-varied sinusoidal wave inputs were used to create electrospun torus shapes. The outer diameter of the tori was found, through parametric analysis, to be rather insensitive to frequency used during deposition, while inner diameter was inversely related to frequency, resulting in overall width of the tori increasing with frequency. Multiplex ES has a high-frequency cutoff based on the time response of the high voltage electrical circuit. These time constants were measured and minimized through the addition of parallel resistors that decreased impedance of the system and improved the high-frequency cutoff by up to 63%.
- Open Access
Quorum Quenching Nanofibers for Anti-Biofouling Applications
Biofilms, complex microbial communities, adept at forming on diverse surfaces within environments, such as membrane technologies, ship hulls, medical devices, and clinical infections, pose persistent challenges. While various biofilm prevention methods, including antimicrobial coatings, physical barriers, and bacteriophage utilization, have been devised for engineered systems, their efficacy fluctuates based on application type and microbial species. Consequently, there remains a pressing need for the development of highly targeted and efficient biofilm control strategies tailored to specific applications remains a pressing need. In our investigation, we disrupt microbial cell-to-cell communication in Pseudomonas aeruginosa through the application of anti-quorum sensing (anti-QS) furanone C-30 molecules. The incorporation of these molecules onto electrospun surfaces yielded substantial reductions of 69% in petri dish assays and 58% on mixed cellulose ester (MCE) membranes in a dead-end nanofiltration system, showcasing the potent anti-biofouling impact. Notably, the functionalization of MCE surfaces with anti-QS molecules resulted in a remarkable 16.7% improvement in filtration output. These findings underscore the potential of this targeted approach to mitigate biofilm formation, offering a technical foundation for advancing tailored strategies in the ongoing pursuit of effective and application-specific biofilm control measures.
Open AccessQuorum Quenching Nanofibers for Anti-Biofouling Applications
Biofilms, complex microbial communities, adept at forming on diverse surfaces within environments, such as membrane technologies, ship hulls, medical devices, and clinical infections, pose persistent challenges. While various biofilm prevention methods, including antimicrobial coatings, physical barriers, and bacteriophage utilization, have been devised for engineered systems, their efficacy fluctuates based on application type and microbial species. Consequently, there remains a pressing need for the development of highly targeted and efficient biofilm control strategies tailored to specific applications remains a pressing need. In our investigation, we disrupt microbial cell-to-cell communication in Pseudomonas aeruginosa through the application of anti-quorum sensing (anti-QS) furanone C-30 molecules. The incorporation of these molecules onto electrospun surfaces yielded substantial reductions of 69% in petri dish assays and 58% on mixed cellulose ester (MCE) membranes in a dead-end nanofiltration system, showcasing the potent anti-biofouling impact. Notably, the functionalization of MCE surfaces with anti-QS molecules resulted in a remarkable 16.7% improvement in filtration output. These findings underscore the potential of this targeted approach to mitigate biofilm formation, offering a technical foundation for advancing tailored strategies in the ongoing pursuit of effective and application-specific biofilm control measures.
- Open Access
- 25 November 2023
- Published by Elsevier in Separation and Purification Technology
- Vol. 332
Electrospun controlled release anti-quorum sensing filter for biofouling prevention in MCE membranes
- 25 November 2023
- Published by Elsevier in Separation and Purification Technology
- Vol. 332
Open AccessElectrospun controlled release anti-quorum sensing filter for biofouling prevention in MCE membranes
- Open Access
- 16 March 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (12) , 15478-15485
Ultrafast Charge Injection in Silver-Modified Graphitic Carbon Nitride
Graphitic carbon nitride (gCN) is a promising organic platform for driving light-activated charge-transfer reactions in a number of valuable photocatalytic cycles. A primary limitation of gCN as a photocatalyst is its short excited-state lifetime, which is mediated by a high density of trap and defect sites that result in rapid excited-state decay and low photocatalytic efficiency. To enhance the catalytic activity, gCN is often functionalized with a metal co-catalyst; however, the mechanism by which metal co-catalysts enhance the reactivity has not been clearly established. In this work, the excited-state dynamics of gCN and silver-modified gCN are compared using ultrafast transient absorption and time-resolved photoluminescence spectroscopies. In silver-modified gCN, an ultrafast spectral shift in the silver plasmon resonance provides direct spectral evidence of electron transfer from gCN to the silver nanoparticles. The electron-transfer rate is competitive with other non-radiative relaxation pathways, with electron-transfer yields approaching 50%, thus providing an effective strategy for mitigating losses associated with defects and trap sites.
- 16 March 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (12) , 15478-15485
Open AccessUltrafast Charge Injection in Silver-Modified Graphitic Carbon Nitride
Graphitic carbon nitride (gCN) is a promising organic platform for driving light-activated charge-transfer reactions in a number of valuable photocatalytic cycles. A primary limitation of gCN as a photocatalyst is its short excited-state lifetime, which is mediated by a high density of trap and defect sites that result in rapid excited-state decay and low photocatalytic efficiency. To enhance the catalytic activity, gCN is often functionalized with a metal co-catalyst; however, the mechanism by which metal co-catalysts enhance the reactivity has not been clearly established. In this work, the excited-state dynamics of gCN and silver-modified gCN are compared using ultrafast transient absorption and time-resolved photoluminescence spectroscopies. In silver-modified gCN, an ultrafast spectral shift in the silver plasmon resonance provides direct spectral evidence of electron transfer from gCN to the silver nanoparticles. The electron-transfer rate is competitive with other non-radiative relaxation pathways, with electron-transfer yields approaching 50%, thus providing an effective strategy for mitigating losses associated with defects and trap sites.
- 25 July 2022
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry B
- Vol. 126 (30) , 5667-5677
Carbon Nanoparticle-Induced Changes to Lipid Monolayer Structure at Water–Air Interfaces
Surface specific vibrational spectroscopy experiments together with surface tension measurements and spectroscopic ellipsometry data were used to characterize the effects of soluble carbon particulates on compressed and partially compressed lipid monolayers adsorbed to the water-air interface. The lipid monolayers consisted of 1,2-dimyristoyl-sn-glycero-3-phosphocholine (DPPC), and measurements were made for both tightly packed monolayers (40 Å2/molecule) and monolayers in their liquid condensed state (55 Å2/molecule). Langmuir trough data show that very small amounts of PHF (0.0075 mg/mL or 6.4 × 10-6 M) decrease lipid film compressibility. This finding supports a cooperative adsorption mechanism whereby the soluble PHFs are drawn to the surface and associate with the insoluble DPPC monolayer. Excess free energies (ΔGmixE) were positive, consistent with the cooperative adsorption mechanism, and although the excess free energies are small (≤1 kJ/mol), adsorbed PHF has measurable effects on monolayer structure. Further support for the cooperative adsorption mechanism at the water-air interface comes from vibrational sum frequency generation (VSFG) experiments. Low PHF concentrations (≤0.06 mg/mL) increase DPPC acyl chain ordering in liquid condensed lipid films and decrease DPPC acyl chain ordering and film thickness in tightly packed lipid films.
- 25 July 2022
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry B
- Vol. 126 (30) , 5667-5677
Carbon Nanoparticle-Induced Changes to Lipid Monolayer Structure at Water–Air Interfaces
Surface specific vibrational spectroscopy experiments together with surface tension measurements and spectroscopic ellipsometry data were used to characterize the effects of soluble carbon particulates on compressed and partially compressed lipid monolayers adsorbed to the water-air interface. The lipid monolayers consisted of 1,2-dimyristoyl-sn-glycero-3-phosphocholine (DPPC), and measurements were made for both tightly packed monolayers (40 Å2/molecule) and monolayers in their liquid condensed state (55 Å2/molecule). Langmuir trough data show that very small amounts of PHF (0.0075 mg/mL or 6.4 × 10-6 M) decrease lipid film compressibility. This finding supports a cooperative adsorption mechanism whereby the soluble PHFs are drawn to the surface and associate with the insoluble DPPC monolayer. Excess free energies (ΔGmixE) were positive, consistent with the cooperative adsorption mechanism, and although the excess free energies are small (≤1 kJ/mol), adsorbed PHF has measurable effects on monolayer structure. Further support for the cooperative adsorption mechanism at the water-air interface comes from vibrational sum frequency generation (VSFG) experiments. Low PHF concentrations (≤0.06 mg/mL) increase DPPC acyl chain ordering in liquid condensed lipid films and decrease DPPC acyl chain ordering and film thickness in tightly packed lipid films.
- 1 November 2019
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 37 (6) , 062002
Combined electrostatic and air driven electrospinning for biomedical applications
Micro-to-nanoscale polymer fiber mats have shown promise across many fields of research, especially in biomedical applications. Electrospinning (ES) is one popular technique used to create high surface-area-to-volume polymer fiber mats. In this work, a portable electrospinning device that utilizes the combined capabilities of electrostatic and air driven technologies was developed for use in biomedical applications. Unlike existing portable electrospinning devices, the combined electrostatic and air driven (EStAD) system contains a completely enclosed electric field, allowing safe and predictable deposition onto flat as well as complex surfaces. Such features also prevent damage to electrospun materials during deposition. Here, biomedically relevant electrospun materials were made using the EStAD device to demonstrate feasibility as compared to a traditional table-top electrospinner that has produced such materials in the past. Results showed successful deposition and use of antibacterial and biomedically relevant nanoparticle release fiber bandages. The versatile nature of the EStAD device will allow the deposition of these materials safely and predictably on charged and uncharged surfaces that are flat or complex, further broadening the applications of ES and providing ease of access to nanomanufacturing of electrospun materials.
- 1 November 2019
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 37 (6) , 062002
Combined electrostatic and air driven electrospinning for biomedical applications
Micro-to-nanoscale polymer fiber mats have shown promise across many fields of research, especially in biomedical applications. Electrospinning (ES) is one popular technique used to create high surface-area-to-volume polymer fiber mats. In this work, a portable electrospinning device that utilizes the combined capabilities of electrostatic and air driven technologies was developed for use in biomedical applications. Unlike existing portable electrospinning devices, the combined electrostatic and air driven (EStAD) system contains a completely enclosed electric field, allowing safe and predictable deposition onto flat as well as complex surfaces. Such features also prevent damage to electrospun materials during deposition. Here, biomedically relevant electrospun materials were made using the EStAD device to demonstrate feasibility as compared to a traditional table-top electrospinner that has produced such materials in the past. Results showed successful deposition and use of antibacterial and biomedically relevant nanoparticle release fiber bandages. The versatile nature of the EStAD device will allow the deposition of these materials safely and predictably on charged and uncharged surfaces that are flat or complex, further broadening the applications of ES and providing ease of access to nanomanufacturing of electrospun materials.
- Open Access
- 1 November 2019
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 37 (6) , 062601
Bulk and localized plasmonic heating in nanogold doped polymers
Colloidal gold (Auc) nanoparticles (GNPs) and nanorods (GNRs) were incorporated into polymer blend films and electrospun fibers to utilize the nanoparticle plasmonic response for localized heating of the polymer. In this work, mathematical modeling was used to describe the GNP distribution and heat/melt profile surrounding each GNP in the polymer blend, demonstrating that a bulk temperature change of only 0.2 °C results in a 20-nm-diameter melted polymer sphere around the GNP. In addition, it was shown that by reducing the radius of polymer material around the GNP through the use of electrospinning fibers in place of thin film deposition, heating of the bulk material increased by 72%. Bulk heating of polymer blend films containing either GNPs or GNRs was mapped using an infrared camera system with light-emitting diodes (LEDs) at 530 and 810 nm. The change in temperature observed in the thin films was used to calculate the photothermal energy conversion efficiency of the respective nanogold doped polymer thin films. Significantly, GNR-doped film efficiencies recorded were up to 6.6 times (558.6% increase) that of the polymer blend-only film when interrogated at 810 nm, while the GNP-doped film efficiency increased by 1.8 times (75.7% increase) under the 530 nm LED.
- 1 November 2019
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 37 (6) , 062601
Open AccessBulk and localized plasmonic heating in nanogold doped polymers
Colloidal gold (Auc) nanoparticles (GNPs) and nanorods (GNRs) were incorporated into polymer blend films and electrospun fibers to utilize the nanoparticle plasmonic response for localized heating of the polymer. In this work, mathematical modeling was used to describe the GNP distribution and heat/melt profile surrounding each GNP in the polymer blend, demonstrating that a bulk temperature change of only 0.2 °C results in a 20-nm-diameter melted polymer sphere around the GNP. In addition, it was shown that by reducing the radius of polymer material around the GNP through the use of electrospinning fibers in place of thin film deposition, heating of the bulk material increased by 72%. Bulk heating of polymer blend films containing either GNPs or GNRs was mapped using an infrared camera system with light-emitting diodes (LEDs) at 530 and 810 nm. The change in temperature observed in the thin films was used to calculate the photothermal energy conversion efficiency of the respective nanogold doped polymer thin films. Significantly, GNR-doped film efficiencies recorded were up to 6.6 times (558.6% increase) that of the polymer blend-only film when interrogated at 810 nm, while the GNP-doped film efficiency increased by 1.8 times (75.7% increase) under the 530 nm LED.