Ali Cherom Kheirabadi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Ali Cherom Kheirabadi has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Dominic Groulx
Mechanical Engineering, Dalhousie University, Halifax, NS B3H 4R2, Canada
3 shared publications Ryozo Nagamune
2 shared publicationsGabrielle Froese
1 shared publication- Ryozo Nagamune
Department of Mechanical Engineering, University of British Columbia, 6250 Applied Science Lane, Vancouver, BC V6T1Z4, Canada
1 shared publication - Shan Yu Ku
Department of Mechanical and Industrial Engineering, University of Toronto, Toronto, ON M5S 3G8, Canada
1 shared publication
Latest Publications
- 22 March 2022
- Published by Elsevier in Renewable Energy
- Vol. 190, 94-102
Optimal layout design of floating offshore wind farms
- 22 March 2022
- Published by Elsevier in Renewable Energy
- Vol. 190, 94-102
Optimal layout design of floating offshore wind farms
- 1 August 2021
- Published by Elsevier in Ocean Engineering
- Vol. 234
A low-fidelity dynamic wind farm model for simulating time-varying wind conditions and floating platform motion
- 1 August 2021
- Published by Elsevier in Ocean Engineering
- Vol. 234
A low-fidelity dynamic wind farm model for simulating time-varying wind conditions and floating platform motion
- Open Access
Distributed Economic Model Predictive Control -- Addressing Non-convexity Using Social Hierarchies
This paper introduces a novel concept for addressing non-convexity in the cost functions of distributed economic model predictive control (DEMPC) systems. Specifically, the proposed algorithm enables agents to self-organize into a hierarchy which determines the order in which control decisions are made. This concept is based on the formation of social hierarchies in nature. An additional feature of the algorithm is that it does not require stationary set-points that are known a priori. Rather, agents negotiate these targets in a truly distributed and scalable manner. Upon providing a detailed description of the algorithm, guarantees of convergence, recursive feasibility, and bounded closed-loop stability are also provided. Finally, the proposed algorithm is compared against a basic parallel distributed economic model predictive controller using an academic numerical example.
Open AccessDistributed Economic Model Predictive Control -- Addressing Non-convexity Using Social Hierarchies
This paper introduces a novel concept for addressing non-convexity in the cost functions of distributed economic model predictive control (DEMPC) systems. Specifically, the proposed algorithm enables agents to self-organize into a hierarchy which determines the order in which control decisions are made. This concept is based on the formation of social hierarchies in nature. An additional feature of the algorithm is that it does not require stationary set-points that are known a priori. Rather, agents negotiate these targets in a truly distributed and scalable manner. Upon providing a detailed description of the algorithm, guarantees of convergence, recursive feasibility, and bounded closed-loop stability are also provided. Finally, the proposed algorithm is compared against a basic parallel distributed economic model predictive controller using an academic numerical example.
- 13 May 2019
- Published by ASME International in Journal of Thermal Science and Engineering Applications
- Vol. 11 (6) , 1-38
The Effectiveness of the Unit Cell Method in Numerically Modeling and Designing Liquid Cooled Heatsinks
This study compares two numerical strategies for modeling flow and heat transfer through mini- and micro- channel heatsinks, the unit cell approximation and the full 3D model, with the objective of validating the former approach. Conjugate heat transfer and laminar flow through a 2×2 cm2 copper-water heatsink are modelled using the finite element package COMSOL Multiphysics 5.0. Parametric studies showed that as the heatsink channels widths were reduced, and the total number of channels increased, temperature and pressure predictions from both models converged to similar values. Relative differences as low as 5.4 and 1.6 % were attained at a channel width of 0.25 mm for maximum wall temperature and channel pressure drop, respectively. Due to its computational efficiency and tendency to conservatively overpredict temperatures relative to the full 3D method, the unit cell approximation is recommended for parametric design of heatsinks with channels widths smaller than 0.5 mm. The unit cell method is then used to design an optimal heatsink for server liquid cooling applications. The heatsink has been fabricated and tested experimentally and its thermal performance is compared with numerical predictions. The unit cell method underestimated the maximum wall temperature relative to experimental results by 3.0 to 14.5 % as the flowrate rose from 0.3 to 1.5 gal/min (1.1 to 5.7 L/min).
- 13 May 2019
- Published by ASME International in Journal of Thermal Science and Engineering Applications
- Vol. 11 (6) , 1-38
The Effectiveness of the Unit Cell Method in Numerically Modeling and Designing Liquid Cooled Heatsinks
This study compares two numerical strategies for modeling flow and heat transfer through mini- and micro- channel heatsinks, the unit cell approximation and the full 3D model, with the objective of validating the former approach. Conjugate heat transfer and laminar flow through a 2×2 cm2 copper-water heatsink are modelled using the finite element package COMSOL Multiphysics 5.0. Parametric studies showed that as the heatsink channels widths were reduced, and the total number of channels increased, temperature and pressure predictions from both models converged to similar values. Relative differences as low as 5.4 and 1.6 % were attained at a channel width of 0.25 mm for maximum wall temperature and channel pressure drop, respectively. Due to its computational efficiency and tendency to conservatively overpredict temperatures relative to the full 3D method, the unit cell approximation is recommended for parametric design of heatsinks with channels widths smaller than 0.5 mm. The unit cell method is then used to design an optimal heatsink for server liquid cooling applications. The heatsink has been fabricated and tested experimentally and its thermal performance is compared with numerical predictions. The unit cell method underestimated the maximum wall temperature relative to experimental results by 3.0 to 14.5 % as the flowrate rose from 0.3 to 1.5 gal/min (1.1 to 5.7 L/min).
- 1 January 2018
- Published by Elsevier in Applied Thermal Engineering
- Vol. 129, 1010-1025
Experimental evaluation of a thermal contact liquid cooling system for server electronics
- 1 January 2018
- Published by Elsevier in Applied Thermal Engineering
- Vol. 129, 1010-1025
Experimental evaluation of a thermal contact liquid cooling system for server electronics
- Top Cited Papers
- 1 July 2016
- Published by Elsevier in Applied Thermal Engineering
- Vol. 105, 622-638
Cooling of server electronics: A design review of existing technology
- 1 July 2016
- Published by Elsevier in Applied Thermal Engineering
- Vol. 105, 622-638
Top Cited PapersCooling of server electronics: A design review of existing technology