Lukas Roy Svane Theisen
Lukas Roy Svane Theisen has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Henrik Niemann
Technical University of Denmark
3 shared publications - Ilmar Ferreira Santos
Technical University of Denmark
3 shared publications - Mogens Blanke
Automation and Control Group, Department of Electrical Engineering, Technical University of Denmark, Lyngby, Denmark
3 shared publications - Roberto Galeazzi
Department of Electrical and Photonics Engineering, Technical University of Denmark, Kongens Lyngby, Denmark
3 shared publications - Fabian G. Pierart
Department of Mechanical Engineering, College of Engineering, Universidad del Bío-Bío, Collao Avenue 1202, Concepción 4051381, Chile
1 shared publication Henrik Niemann
1 shared publication
Latest Publications
- 19 June 2026
- Published by The CACHE Foundation, Inc.
- Vol. 6, 1298-1305
Modelling of fouling dynamics in a falling-film evaporator
Fouling is a persistent issue in industrial heat-transfer equipment, increasing energy demand and reducing efficiency. This is also true in the dairy industry where falling-film evaporators are central to powder production. Most dynamic models, however, neglect gradual fouling, limiting predictive accuracy during extended operation. As a result, model-based control can become unreliable when fouling becomes significant. The dynamic models by Bojnourd et al. [1] are widely used but assume clean-surface operation. While this captures short-term thermal behavior, it cannot represent the progressive decline in heat-transfer performance caused by fouling. Díaz-Ovalle et al. [2] introduced a fouling-layer model that explicitly describes the growth of a fouling deposit over time. Building on this concept, the present work incorporates a simple dynamic fouling model for falling-film evaporators and validates it using industrial data from a four-effect evaporator using thermal vapor recompression. Two fouling-modelling strategies are evaluated: a mechanistic fouling layer model and an empirical model describing the observed loss in heat-transfer efficiency. The fouling layer model substantially reduces prediction error, demonstrating that it captures the dominant fouling behavior. Although the empirical model fits all observed discrepancies, it lacks predictive capability and therefore cannot be applied for model-based prediction or control.
- 19 June 2026
- Published by The CACHE Foundation, Inc.
- Vol. 6, 1298-1305
Modelling of fouling dynamics in a falling-film evaporator
Fouling is a persistent issue in industrial heat-transfer equipment, increasing energy demand and reducing efficiency. This is also true in the dairy industry where falling-film evaporators are central to powder production. Most dynamic models, however, neglect gradual fouling, limiting predictive accuracy during extended operation. As a result, model-based control can become unreliable when fouling becomes significant. The dynamic models by Bojnourd et al. [1] are widely used but assume clean-surface operation. While this captures short-term thermal behavior, it cannot represent the progressive decline in heat-transfer performance caused by fouling. Díaz-Ovalle et al. [2] introduced a fouling-layer model that explicitly describes the growth of a fouling deposit over time. Building on this concept, the present work incorporates a simple dynamic fouling model for falling-film evaporators and validates it using industrial data from a four-effect evaporator using thermal vapor recompression. Two fouling-modelling strategies are evaluated: a mechanistic fouling layer model and an empirical model describing the observed loss in heat-transfer efficiency. The fouling layer model substantially reduces prediction error, demonstrating that it captures the dominant fouling behavior. Although the empirical model fits all observed discrepancies, it lacks predictive capability and therefore cannot be applied for model-based prediction or control.
- Open Access
- 1 March 2016
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 70-71, 1150-1170
Modelling and identification for control of gas bearings
- 1 March 2016
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 70-71, 1150-1170
Open AccessModelling and identification for control of gas bearings
- Open Access
- 19 November 2015
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 659 (1) , 012017
Gas Bearing Control for Safe Operation in Critical Speed Regions - Experimental Verification
Gas bearings are popular for their high speed capabilities, low friction and clean operation, but require low clearances and suffer from poor damping properties. The poor damping properties cause high disturbance amplification near the natural frequencies. These become critical when the rotation speed coincides with a natural frequency. In these regions, even low mass unbalances can cause rub and damage the machine. To prevent rubbing, the variation of the rotation speed of machines supported by gas bearings has to be carefully conducted during run-ups and run-downs, by acceleration and deceleration patterns and avoidance of operation near the critical speeds, which is a limiting factor during operation, specially during run-downs. An approach for reducing the vibrations is by feedback controlled lubrication. This paper addresses the challenge of reducing vibrations in rotating machines supported by gas bearings to extend their operating range. Using H∞-design methods, active lubrication techniques are proposed to enhance the damping, which in turn reduces the vibrations to a desired safe level. The control design is validated experimentally on a laboratory test rig, and shown to allow safe shaft rotation speeds up to, in and above the two first critical speeds, which significantly extends the operating range.
- 19 November 2015
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 659 (1) , 012017
Open AccessGas Bearing Control for Safe Operation in Critical Speed Regions - Experimental Verification
Gas bearings are popular for their high speed capabilities, low friction and clean operation, but require low clearances and suffer from poor damping properties. The poor damping properties cause high disturbance amplification near the natural frequencies. These become critical when the rotation speed coincides with a natural frequency. In these regions, even low mass unbalances can cause rub and damage the machine. To prevent rubbing, the variation of the rotation speed of machines supported by gas bearings has to be carefully conducted during run-ups and run-downs, by acceleration and deceleration patterns and avoidance of operation near the critical speeds, which is a limiting factor during operation, specially during run-downs. An approach for reducing the vibrations is by feedback controlled lubrication. This paper addresses the challenge of reducing vibrations in rotating machines supported by gas bearings to extend their operating range. Using H∞-design methods, active lubrication techniques are proposed to enhance the damping, which in turn reduces the vibrations to a desired safe level. The control design is validated experimentally on a laboratory test rig, and shown to allow safe shaft rotation speeds up to, in and above the two first critical speeds, which significantly extends the operating range.
- Open Access
- 16 December 2014
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 570 (5)
Modelling of Rotor-gas bearings for Feedback Controller Design
- 16 December 2014
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 570 (5)
Open AccessModelling of Rotor-gas bearings for Feedback Controller Design
- 15 August 2014
- Published by Springer Nature
- p. 963-976
Experimental Grey Box Model Identification and Control of an Active Gas Bearing
- 15 August 2014
- Published by Springer Nature
- p. 963-976
Experimental Grey Box Model Identification and Control of an Active Gas Bearing
- Open Access
- 1 January 2013
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 46 (33) , 150-155
Unmanned Water Craft Identification and Adaptive Control in Low-Speed and Reversing Regions
- 1 January 2013
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 46 (33) , 150-155
Open AccessUnmanned Water Craft Identification and Adaptive Control in Low-Speed and Reversing Regions