Claudia A. Capeletto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Claudia A. Capeletto has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Claudia Sayer
Universidade Federal de Santa Catarina, Brasil
4 shared publications - Pedro Henrique Hermes de Araújo
Universidade Federal de Santa Catarina, Brazil
4 shared publications - Adriano da Silva
Federal University of Santa Catarina
2 shared publications - Viviana Cocco Mariani
Department of Electrical Engineering, Federal University of Paraná, Curitiba, Brazil
2 shared publications - Éliton Fontana
Department of Chemical Engineering, Sector of Technology Federal University of Paraná Curitiba Brazil
2 shared publications - Amabille Petza Kloc
Department of Biochemical and Chemical Engineering, Laboratory of Thermodynamics, TU Dortmund University, Emil-Figge-Str. 70, Dortmund D-44227, Germany
1 shared publication
Latest Publications
- 1 December 2019
- Published by Elsevier in Fluid Phase Equilibria
- Vol. 502
Phase equilibrium measurements and thermodynamic modeling of {CO2 + diethyl succinate + cosolvent} systems
- 1 December 2019
- Published by Elsevier in Fluid Phase Equilibria
- Vol. 502
Phase equilibrium measurements and thermodynamic modeling of {CO2 + diethyl succinate + cosolvent} systems
- 4 January 2017
- Published by Wiley in AIChE Journal
- Vol. 63 (6) , 2128-2140
Mathematical modeling of molecular weight distribution in miniemulsion polymerization with oil‐soluble initiator
A mathematical model for the study of reaction kinetics and molecular weight distributions in miniemulsion polymerization systems with oil‐soluble initiators is presented. The mathematical model allows the computation of the evolution of the complete molecular weight distribution with chain lengths of up to 105 mers in miniemulsion polymerization by direct integration in reasonable computational time. Also, no restriction in the kinetic regime is needed, as the model is able to represent both compartmentalized and pseud‐bulk systems. The model was validated with experimental results for methyl methacrylate and styrene homopolymerizations, with two different oil‐soluble initiators, and adequately represented both the kinetics and molecular weight distributions of these systems. © 2017 American Institute of Chemical Engineers AIChE J, 63: 2128–2140, 2017
- 4 January 2017
- Published by Wiley in AIChE Journal
- Vol. 63 (6) , 2128-2140
Mathematical modeling of molecular weight distribution in miniemulsion polymerization with oil‐soluble initiator
A mathematical model for the study of reaction kinetics and molecular weight distributions in miniemulsion polymerization systems with oil‐soluble initiators is presented. The mathematical model allows the computation of the evolution of the complete molecular weight distribution with chain lengths of up to 105 mers in miniemulsion polymerization by direct integration in reasonable computational time. Also, no restriction in the kinetic regime is needed, as the model is able to represent both compartmentalized and pseud‐bulk systems. The model was validated with experimental results for methyl methacrylate and styrene homopolymerizations, with two different oil‐soluble initiators, and adequately represented both the kinetics and molecular weight distributions of these systems. © 2017 American Institute of Chemical Engineers AIChE J, 63: 2128–2140, 2017
- 1 May 2016
- Published by Elsevier in Chemical Engineering and Processing - Process Intensification
- Vol. 103, 80-86
Post-modification of preformed polymer latex
- 1 May 2016
- Published by Elsevier in Chemical Engineering and Processing - Process Intensification
- Vol. 103, 80-86
Post-modification of preformed polymer latex
- 1 February 2015
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 81, 829-845
Numerical analysis of mixed convection in partially open cavities heated from below
- 1 February 2015
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 81, 829-845
Numerical analysis of mixed convection in partially open cavities heated from below
- 25 September 2014
- Published by Wiley in Macromolecular Symposia
- Vol. 343 (1) , 31-38
Synthesis of Core‐Shell Particles with Low Molecular Weight Alkanes by Miniemulsion Polymerization
Summary: Miniemulsion polymerization technique was used to obtain core‐shell nanoparticles with a core of low molecular weight alkanes and a polystyrene shell. Reactions were performed at 80°C for 5 hours using benzoyl peroxide as oil‐soluble initiator. The effect of different alkane types, namely n‐hexadecane, n‐octane and n‐heptane, and initiator concentrations on reaction rates, particle sizes, molecular weights and particles morphology were evaluated. When shorter chain alkanes as n‐heptane and n‐octane were used it was observed lower reaction rates, higher particle sizes and less sharp particle morphology than in reactions with hexadecane in which well formed core‐shell particles were obtained. These results were assigned to the plasticizing effect and higher water‐solubility of n‐octane and n‐heptane, responsible for decreasing the gel effect and favoring the diffusional degradation.
- 25 September 2014
- Published by Wiley in Macromolecular Symposia
- Vol. 343 (1) , 31-38
Synthesis of Core‐Shell Particles with Low Molecular Weight Alkanes by Miniemulsion Polymerization
Summary: Miniemulsion polymerization technique was used to obtain core‐shell nanoparticles with a core of low molecular weight alkanes and a polystyrene shell. Reactions were performed at 80°C for 5 hours using benzoyl peroxide as oil‐soluble initiator. The effect of different alkane types, namely n‐hexadecane, n‐octane and n‐heptane, and initiator concentrations on reaction rates, particle sizes, molecular weights and particles morphology were evaluated. When shorter chain alkanes as n‐heptane and n‐octane were used it was observed lower reaction rates, higher particle sizes and less sharp particle morphology than in reactions with hexadecane in which well formed core‐shell particles were obtained. These results were assigned to the plasticizing effect and higher water‐solubility of n‐octane and n‐heptane, responsible for decreasing the gel effect and favoring the diffusional degradation.
- 1 June 2013
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 61, 525-542
Three-dimensional analysis of natural convection in a partially-open cavity with internal heat source
- 1 June 2013
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 61, 525-542
Three-dimensional analysis of natural convection in a partially-open cavity with internal heat source
- 1 September 2012
- Published by Wiley in Macromolecular Symposia
- Vol. 319 (1) , 54-63
Styrene Miniemulsion Polymerization: Incorporation of N-Alkanes
- 1 September 2012
- Published by Wiley in Macromolecular Symposia
- Vol. 319 (1) , 54-63
Styrene Miniemulsion Polymerization: Incorporation of N-Alkanes