Dianhai Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Dianhai Zhang has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Chang-Seop Koh
Chungbuk National University
11 shared publications - Yanli Zhang
Shenyang University of Technology
10 shared publications - Ziyan Ren
School of Electrical Engineering, Shenyang University of Technology, Liaoning, China
9 shared publications Kaimeng Shi
School of Electrical Engineering, Shenyang University of Technology, Liaoning, China
7 shared publications- Dezhi Chen
Shenyang University of Technology
5 shared publications Ziyan Ren
Shenyang University of Technology
5 shared publications
Latest Publications
- 11 February 2026
- Published by Springer Nature
- p. 379-393
Vectorization and Parameter Identification Method of Analytical Preisach Model
- 11 February 2026
- Published by Springer Nature
- p. 379-393
Vectorization and Parameter Identification Method of Analytical Preisach Model
- 18 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 61 (11) , 1-8
Accurate Prediction of Eddy Current Losses in SMC Cores Considering Skin Effect and Contact Deformation Based on Analytical Calculation
An analytical method for predicting high-frequency eddy current losses in soft magnetic composites (SMC) cores by combining mesoscopic and macroscopic perspectives is proposed, bridging the link between mesoscopic structural features and macroscopic electromagnetic response. Existing methods lack a quantitative mapping (particle strain stress and contact conductive network) between mesoscopic structures (particle strain, inter-particle contact) and eddy current losses, and macroscopic models fail to capture the skin effect under high-frequency excitation. To address this problem, first, a strain-dependent conductivity model is proposed, which incorporates the particle compaction stages (separation, contact, and connection stages). Second, analytical expressions are proposed to predict high-frequency intra-particle and inter-particle eddy current losses, taking into account the skin effect. Finally, the practicality and effectiveness of the method is verified by comparing experimental results.
- 18 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 61 (11) , 1-8
Accurate Prediction of Eddy Current Losses in SMC Cores Considering Skin Effect and Contact Deformation Based on Analytical Calculation
An analytical method for predicting high-frequency eddy current losses in soft magnetic composites (SMC) cores by combining mesoscopic and macroscopic perspectives is proposed, bridging the link between mesoscopic structural features and macroscopic electromagnetic response. Existing methods lack a quantitative mapping (particle strain stress and contact conductive network) between mesoscopic structures (particle strain, inter-particle contact) and eddy current losses, and macroscopic models fail to capture the skin effect under high-frequency excitation. To address this problem, first, a strain-dependent conductivity model is proposed, which incorporates the particle compaction stages (separation, contact, and connection stages). Second, analytical expressions are proposed to predict high-frequency intra-particle and inter-particle eddy current losses, taking into account the skin effect. Finally, the practicality and effectiveness of the method is verified by comparing experimental results.
- Open Access
Literature Reviews of Topology Optimal Design Methods and Applications in Magnetic Devices
With the evolution of magnetic devices toward structural innovation and high reliability, the traditional design methods, such as size optimization and shape optimization, are limited by preset structural forms, making it challenging to generate novel structures and topologies. Topology-optimized design methods can achieve an optimal distribution of constituent materials of magnetic devices by optimizing the objective performance subject to certain constraints, and can provide greater freedom for designers. Based on the above background, this paper firstly investigates the principles of deterministic topology optimization methods, and introduces the latest specific applications in magnetic devices. It also demonstrates the advantages of topology optimization technology in enhancing operating performance, fostering structural innovation, and improving material utilization in magnetic devices. To manage uncertainties in design and manufacturing processes of magnetic devices, this paper analyzes uncertainty topology optimization methods, respectively, reliability and robustness-based topology optimization algorithms. To facilitate manufacturing, this paper summarizes the filter strategy for the new structure obtained by topology optimization. Finally, the problems faced by the topology optimization method in the field of magnetic devices are discussed, and a future development direction is projected.
Open AccessLiterature Reviews of Topology Optimal Design Methods and Applications in Magnetic Devices
With the evolution of magnetic devices toward structural innovation and high reliability, the traditional design methods, such as size optimization and shape optimization, are limited by preset structural forms, making it challenging to generate novel structures and topologies. Topology-optimized design methods can achieve an optimal distribution of constituent materials of magnetic devices by optimizing the objective performance subject to certain constraints, and can provide greater freedom for designers. Based on the above background, this paper firstly investigates the principles of deterministic topology optimization methods, and introduces the latest specific applications in magnetic devices. It also demonstrates the advantages of topology optimization technology in enhancing operating performance, fostering structural innovation, and improving material utilization in magnetic devices. To manage uncertainties in design and manufacturing processes of magnetic devices, this paper analyzes uncertainty topology optimization methods, respectively, reliability and robustness-based topology optimization algorithms. To facilitate manufacturing, this paper summarizes the filter strategy for the new structure obtained by topology optimization. Finally, the problems faced by the topology optimization method in the field of magnetic devices are discussed, and a future development direction is projected.
- 25 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 60 (11) , 1-8
Semi-Analytical Method for Evaluating Magnetic Properties of SMC Based on Homogenization Model
A semi-analytical method is presented in this article for evaluating the magnetic properties of soft magnetic composites (SMCs), and the quantitative structure-activity relationship between microstructural parameters and macroscopic magnetic properties of SMCs is investigated. First, a new homogenization model is developed with the objective of characterizing the microstructure of SMC. The concepts of insulating layer, pore, and surface roughness structure are introduced. Meanwhile, the thickness of the insulating layer is calculated using the least square, the mass density and volume fraction of the particles are determined using a discrete element method (DEM), and the surface roughness of the particles is characterized using a periodic square waveform. Then, by analyzing the relationship between the microstructural parameters and magnetic properties, analytical expressions are derived to realize the evaluation of the macroscopic permeability and eddy current loss of the SMC. Finally, the SMC-prepared samples are tested by the dc magnetization method and ring sample method, respectively, to verify the reliability of the proposed semi-analytical method by comparing the experimental and evaluation results.
- 25 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 60 (11) , 1-8
Semi-Analytical Method for Evaluating Magnetic Properties of SMC Based on Homogenization Model
A semi-analytical method is presented in this article for evaluating the magnetic properties of soft magnetic composites (SMCs), and the quantitative structure-activity relationship between microstructural parameters and macroscopic magnetic properties of SMCs is investigated. First, a new homogenization model is developed with the objective of characterizing the microstructure of SMC. The concepts of insulating layer, pore, and surface roughness structure are introduced. Meanwhile, the thickness of the insulating layer is calculated using the least square, the mass density and volume fraction of the particles are determined using a discrete element method (DEM), and the surface roughness of the particles is characterized using a periodic square waveform. Then, by analyzing the relationship between the microstructural parameters and magnetic properties, analytical expressions are derived to realize the evaluation of the macroscopic permeability and eddy current loss of the SMC. Finally, the SMC-prepared samples are tested by the dc magnetization method and ring sample method, respectively, to verify the reliability of the proposed semi-analytical method by comparing the experimental and evaluation results.
- 1 April 2024
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 597
An improved dynamic magnetic hysteresis model in soft magnetic composites
- 1 April 2024
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 597
An improved dynamic magnetic hysteresis model in soft magnetic composites
- 20 January 2024
- Published by Springer Nature
- p. 367-377
Level Set Method Assisted Topology Optimization of Permanent Magnet Synchronous Machine
- 20 January 2024
- Published by Springer Nature
- p. 367-377
Level Set Method Assisted Topology Optimization of Permanent Magnet Synchronous Machine
- 26 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 60 (2) , 1-8
Effect of Particles Size on Eddy-Current Loss of Soft Magnetic Composites Using Combined DEM and FEM
A method is proposed in this article to study the effect of particle size distribution on eddy-current loss from the microstructure model of soft magnetic composite (SMC). Unlike the previous ones, the microstructural model in this article is constructed based on the simulation data of the powder densification process. The simulation process uses the discrete element method (DEM), and the construction process is completed by the proposed 3-D reconstruction program. The generated model is analyzed by the finite element method (FEM) to investigate the differences between the eddy-current loss of SMCs with multiple particle size distributions. The analysis separates the eddy-current loss into intra-particle and inter-particle ones at the microscopic level, and an equation applicable to the calculation of eddy-current loss is proposed accordingly. For the eddy-current loss inside the particles, when the frequency increases so that the skin depth is smaller than the average particle size, the loss is no longer the square of the frequency. The experimental results show that the equation can accurately calculate the eddy-current loss under different particle size distributions. Moreover, the degree of intermetallic insulation of the particles plays a crucial role in regulating the eddy-current loss, especially for smaller particle-size SMCs.
- 26 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 60 (2) , 1-8
Effect of Particles Size on Eddy-Current Loss of Soft Magnetic Composites Using Combined DEM and FEM
A method is proposed in this article to study the effect of particle size distribution on eddy-current loss from the microstructure model of soft magnetic composite (SMC). Unlike the previous ones, the microstructural model in this article is constructed based on the simulation data of the powder densification process. The simulation process uses the discrete element method (DEM), and the construction process is completed by the proposed 3-D reconstruction program. The generated model is analyzed by the finite element method (FEM) to investigate the differences between the eddy-current loss of SMCs with multiple particle size distributions. The analysis separates the eddy-current loss into intra-particle and inter-particle ones at the microscopic level, and an equation applicable to the calculation of eddy-current loss is proposed accordingly. For the eddy-current loss inside the particles, when the frequency increases so that the skin depth is smaller than the average particle size, the loss is no longer the square of the frequency. The experimental results show that the equation can accurately calculate the eddy-current loss under different particle size distributions. Moreover, the degree of intermetallic insulation of the particles plays a crucial role in regulating the eddy-current loss, especially for smaller particle-size SMCs.
- 30 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (5) , 1-4
Evaluation of Equivalent Permeability of Soft Magnetic Composites Considering Manufacturing Process
A method for evaluating the equivalent permeability of soft magnetic composites is presented. Firstly, a new microstructural characterization model of soft magnetic composites is proposed, which introduces the concepts of pores and gaps. The effect of these two structures on the magnetic properties of composites is analyzed, and an analytical model is derived from the microstructural parameters. Secondly, the compaction process is numerically simulated by discrete element method and powder particle 3D reconstruction technique. The microstructure models of soft magnetic composites under different compaction conditions are established. Finally, the magnetic field characteristics of the microstructure model are analyzed by finite element method, and the equivalent permeability is accurately evaluated. The correctness and feasibility of the simulation method proposed in this paper is verified by comparing with the measured results.
- 30 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 59 (5) , 1-4
Evaluation of Equivalent Permeability of Soft Magnetic Composites Considering Manufacturing Process
A method for evaluating the equivalent permeability of soft magnetic composites is presented. Firstly, a new microstructural characterization model of soft magnetic composites is proposed, which introduces the concepts of pores and gaps. The effect of these two structures on the magnetic properties of composites is analyzed, and an analytical model is derived from the microstructural parameters. Secondly, the compaction process is numerically simulated by discrete element method and powder particle 3D reconstruction technique. The microstructure models of soft magnetic composites under different compaction conditions are established. Finally, the magnetic field characteristics of the microstructure model are analyzed by finite element method, and the equivalent permeability is accurately evaluated. The correctness and feasibility of the simulation method proposed in this paper is verified by comparing with the measured results.
- 24 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Determination of Equivalent Permeability of Soft Magnetic Composites Considering Manufacturing Process
A novel evaluation method of the equivalent permeability of soft magnetic composites (SMC) is proposed, referring to the pressing mechanism. Firstly, the microstructure of the SMC is analyzed, and the region between ferromagnetic particles is divided into gaps and pores. An analytical calculation method for two permeability boundaries is derived when the non-ferromagnetic region is completely occupied by gaps or pores. Finally, the accurate homogenized permeability can be determined in terms of composites density and the ratio of gaps and pores which is affected by the manufacturing process parameters during preparation. The proposed method can tentatively predict the magnetic properties of composites, thereby helping select appropriate processing parameters.
- 24 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Determination of Equivalent Permeability of Soft Magnetic Composites Considering Manufacturing Process
A novel evaluation method of the equivalent permeability of soft magnetic composites (SMC) is proposed, referring to the pressing mechanism. Firstly, the microstructure of the SMC is analyzed, and the region between ferromagnetic particles is divided into gaps and pores. An analytical calculation method for two permeability boundaries is derived when the non-ferromagnetic region is completely occupied by gaps or pores. Finally, the accurate homogenized permeability can be determined in terms of composites density and the ratio of gaps and pores which is affected by the manufacturing process parameters during preparation. The proposed method can tentatively predict the magnetic properties of composites, thereby helping select appropriate processing parameters.