John P. Prineas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
John P. Prineas has a total of 305 co-authors. Here are the top co-authors by number of shared publications:
G. Khitrova
University of Arizona
24 shared publicationsC. Ell
University of Arizona
21 shared publicationsH. M. Gibbs
University of Arizona
17 shared publications- Jonathon T. Olesberg
Department of Chemistry and Optical Science and Technology Center, University of Iowa, Iowa City, IA, USA
17 shared publications H.M. Gibbs
15 shared publicationsS. W. Koch
Philipps-Univ. Marburg (Germany)
14 shared publications
Latest Publications
- 18 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. PP (00189197) , 1
Next Generation 1024x1024 Individually Addressable Mid-Infrared LED Arrays Based on Cascaded W-Superlattice Emitters
Mid-infrared light-emitting diodes (IRLEDs) offer high modulation bandwidth, high apparent radiance, and analog grayscale operation, making them attractive for large-area patterned emitters and high-speed illumination systems. However, their practical use in dense arrays has been limited by low wall-plug efficiency and thermal performance. Here we demonstrate a 1024×1024, 24 μm pitch mid-infrared IRLED array based on a 16-stage cascaded W-superlattice emitter, quadrupling the pixel count of prior 512×512 arrays. Improvements in superlattice design, backside roughening, and hybridization enabled >99% operability, with apparent temperatures of >1300 K for the full array, ≈1700 K in a quadrant, and >2000 K in process evaluation chips (PEC) devices, and wall-plug efficiencies up to ~1% at low injection. Advances in system control electronics and nanosecond-scale pixel response enabled >400 Hz frame rates with 11-bit radiance resolution. System performance is primarily limited by thermal droop under high drive, but synchronous operation enabled full-array output to 300 K with 2500 K apparent temperature for ~1% of pixels with enhanced cooling and active thermal management. These results establish large-format IRLED emitter arrays as a scalable platform for high-speed infrared illumination and pattern generation and show a path toward further performance gains through improved wall-plug efficiency and thermal control.
- 18 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. PP (00189197) , 1
Next Generation 1024x1024 Individually Addressable Mid-Infrared LED Arrays Based on Cascaded W-Superlattice Emitters
Mid-infrared light-emitting diodes (IRLEDs) offer high modulation bandwidth, high apparent radiance, and analog grayscale operation, making them attractive for large-area patterned emitters and high-speed illumination systems. However, their practical use in dense arrays has been limited by low wall-plug efficiency and thermal performance. Here we demonstrate a 1024×1024, 24 μm pitch mid-infrared IRLED array based on a 16-stage cascaded W-superlattice emitter, quadrupling the pixel count of prior 512×512 arrays. Improvements in superlattice design, backside roughening, and hybridization enabled >99% operability, with apparent temperatures of >1300 K for the full array, ≈1700 K in a quadrant, and >2000 K in process evaluation chips (PEC) devices, and wall-plug efficiencies up to ~1% at low injection. Advances in system control electronics and nanosecond-scale pixel response enabled >400 Hz frame rates with 11-bit radiance resolution. System performance is primarily limited by thermal droop under high drive, but synchronous operation enabled full-array output to 300 K with 2500 K apparent temperature for ~1% of pixels with enhanced cooling and active thermal management. These results establish large-format IRLED emitter arrays as a scalable platform for high-speed infrared illumination and pattern generation and show a path toward further performance gains through improved wall-plug efficiency and thermal control.
- Open Access
- 9 January 2026
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 20 (3) , 2872-2880
Engineering Nanohole-Etched Quantum Dots for Telecom-Band Single-Photon Generation
Bright and high-purity single-photon sources at telecom wavelengths are essential for scalable quantum networks. Nanohole-etched GaSb/AlGaSb quantum dots (QDs) are an emerging platform for telecom-band emitters, offering freedom from strain-induced decoherence and indium-related nuclear spin noise of conventional InGaAs QDs. Here, we present a comprehensive optical spectroscopy study that reveals correlations between nanohole morphology, exciton recombination dynamics, and single-photon performance in GaSb QDs. Shallow nanoholes lead to ultrafast charge transfer that limits optical coherence, whereas deeper nanoholes yield clean neutral-exciton emission with a high bright-to-dark state branching ratio (98 ± 1%), indicating favorable conditions for efficient photon generation. Under pulsed quasi-resonant excitation, these QDs exhibit significantly enhanced single-photon purity with g(2)(0) = 0.029 ± 0.011, compared to above-band excitation (g(2)(0) = 0.18 ± 0.05). Polarization-resolved measurements across tens of QDs further reveal ultrasmall fine-structure splitting of the neutral exciton (11 ± 5 μeV), relevant for entangled-photon generation at telecom wavelengths. These results highlight the potential of GaSb QDs for high-performance quantum emitters and scalable spin-photon interfaces in the telecom band.
- 9 January 2026
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 20 (3) , 2872-2880
Open AccessEngineering Nanohole-Etched Quantum Dots for Telecom-Band Single-Photon Generation
Bright and high-purity single-photon sources at telecom wavelengths are essential for scalable quantum networks. Nanohole-etched GaSb/AlGaSb quantum dots (QDs) are an emerging platform for telecom-band emitters, offering freedom from strain-induced decoherence and indium-related nuclear spin noise of conventional InGaAs QDs. Here, we present a comprehensive optical spectroscopy study that reveals correlations between nanohole morphology, exciton recombination dynamics, and single-photon performance in GaSb QDs. Shallow nanoholes lead to ultrafast charge transfer that limits optical coherence, whereas deeper nanoholes yield clean neutral-exciton emission with a high bright-to-dark state branching ratio (98 ± 1%), indicating favorable conditions for efficient photon generation. Under pulsed quasi-resonant excitation, these QDs exhibit significantly enhanced single-photon purity with g(2)(0) = 0.029 ± 0.011, compared to above-band excitation (g(2)(0) = 0.18 ± 0.05). Polarization-resolved measurements across tens of QDs further reveal ultrasmall fine-structure splitting of the neutral exciton (11 ± 5 μeV), relevant for entangled-photon generation at telecom wavelengths. These results highlight the potential of GaSb QDs for high-performance quantum emitters and scalable spin-photon interfaces in the telecom band.
- 1 December 2025
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 15 (12) , 3274
Complex oxide thin films towards surface-phonon-polariton-based infrared optoelectronics [Invited]
Infrared nanophotonics offers enormous potential for enhancing infrared optoelectronic technologies, due to the ability to confine light to deeply sub-wavelength dimensions. One of the limitations of traditional nanophotonics approaches is the inherent losses present in the plasmonic materials that are conventionally used. Surface phonon polaritons offer a lower-loss alternative but are more difficult to integrate with conventional III-V-based semiconductors used for infrared optoelectronics. In this work, we examine the properties of complex oxides, which can be grown directly onto III-V semiconductors for the purpose of infrared light detection. We grow films of both SrTiO 3 and BaTiO 3 on GaAs using pulsed laser deposition, and examine their properties using a combination of X-ray diffraction, atomic force microscopy, transmission electron microscopy, and infrared reflectance spectroscopy. We find that the films grown exhibit good crystallinity with smooth, uniform surfaces, and with occasional minor misoriented grains. Their optical properties indicate higher losses than perfect single crystal substrates, but by less than a factor of two, with phonon Q factors of 18-60, which is favorable when compared with plasmonic materials. We then conduct numerical simulations, which show that these films can be used to create surface phonon polariton infrared detectors that outperform similar metallic gratings by a factor of four. Our results show that the integration of oxide materials with conventional semiconductors is a viable route to improving infrared detector technology, competitive with other nanophotonics approaches.
- 1 December 2025
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 15 (12) , 3274
Complex oxide thin films towards surface-phonon-polariton-based infrared optoelectronics [Invited]
Infrared nanophotonics offers enormous potential for enhancing infrared optoelectronic technologies, due to the ability to confine light to deeply sub-wavelength dimensions. One of the limitations of traditional nanophotonics approaches is the inherent losses present in the plasmonic materials that are conventionally used. Surface phonon polaritons offer a lower-loss alternative but are more difficult to integrate with conventional III-V-based semiconductors used for infrared optoelectronics. In this work, we examine the properties of complex oxides, which can be grown directly onto III-V semiconductors for the purpose of infrared light detection. We grow films of both SrTiO 3 and BaTiO 3 on GaAs using pulsed laser deposition, and examine their properties using a combination of X-ray diffraction, atomic force microscopy, transmission electron microscopy, and infrared reflectance spectroscopy. We find that the films grown exhibit good crystallinity with smooth, uniform surfaces, and with occasional minor misoriented grains. Their optical properties indicate higher losses than perfect single crystal substrates, but by less than a factor of two, with phonon Q factors of 18-60, which is favorable when compared with plasmonic materials. We then conduct numerical simulations, which show that these films can be used to create surface phonon polariton infrared detectors that outperform similar metallic gratings by a factor of four. Our results show that the integration of oxide materials with conventional semiconductors is a viable route to improving infrared detector technology, competitive with other nanophotonics approaches.
- 4 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 61 (4) , 1-8
Color Crosstalk in Two-Color Mid-Infrared LEDs With and Without Cavity Enhancement
Mid-infrared (3–$5~\mu $ m) LEDs have assumed greater importance optical gas sensors and have been explored for use in midinfrared LED arrays, in both cases to replace thermal pixels. Compared to thermal pixels, mid-infrared LEDs have near instantaneous settling times, achieve higher radiance, can have multi-spectral output, and are safer. Multispectral output creates the possibility of emission into narrowed bands for either sensing multiple gas species or creating dual emission thermal pixel arrays. However, their adoption for these applications is hindered by spectral crosstalk from emission tails at room temperature, and additionally by low efficiency, problematic in dense LED arrays with strict power density requirements. This work explores three approaches to designing two-color mid-infrared LED arrays, targeting reduced spectral crosstalk and lower power requirements: 1) monolithic two-color LEDs; 2) monolithic two-color cavity LEDs; and 3) filtered single-color cavity LEDs combined spatially. Performance metrics, such as power-to-temperature efficiency and radiance-to-crosstalk ratios, are compared across designs. Incorporation of cavities narrows emission, improves spectral radiance by 5–$10\times $ and overlap with the emission band, lowers power requirements by ~2–$3\times $ , and can reduce crosstalk. In-band to cross-band radiance ratio is generally limited to around 10–$1000\times $ for monolithic two-color devices; two single color devices allow external filtering which improves the ratio to$10^{5}$ –$10^{7}$ . Results provide a framework for use of mid-infrared LEDs in multi-gas sensing and two-color mid-infrared LED arrays.- 4 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 61 (4) , 1-8
Color Crosstalk in Two-Color Mid-Infrared LEDs With and Without Cavity Enhancement
Mid-infrared (3–$5~\mu $ m) LEDs have assumed greater importance optical gas sensors and have been explored for use in midinfrared LED arrays, in both cases to replace thermal pixels. Compared to thermal pixels, mid-infrared LEDs have near instantaneous settling times, achieve higher radiance, can have multi-spectral output, and are safer. Multispectral output creates the possibility of emission into narrowed bands for either sensing multiple gas species or creating dual emission thermal pixel arrays. However, their adoption for these applications is hindered by spectral crosstalk from emission tails at room temperature, and additionally by low efficiency, problematic in dense LED arrays with strict power density requirements. This work explores three approaches to designing two-color mid-infrared LED arrays, targeting reduced spectral crosstalk and lower power requirements: 1) monolithic two-color LEDs; 2) monolithic two-color cavity LEDs; and 3) filtered single-color cavity LEDs combined spatially. Performance metrics, such as power-to-temperature efficiency and radiance-to-crosstalk ratios, are compared across designs. Incorporation of cavities narrows emission, improves spectral radiance by 5–$10\times $ and overlap with the emission band, lowers power requirements by ~2–$3\times $ , and can reduce crosstalk. In-band to cross-band radiance ratio is generally limited to around 10–$1000\times $ for monolithic two-color devices; two single color devices allow external filtering which improves the ratio to$10^{5}$ –$10^{7}$ . Results provide a framework for use of mid-infrared LEDs in multi-gas sensing and two-color mid-infrared LED arrays.- Open Access
- 8 May 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (18)
Microcavity enhancement vs Auger recombination in variable thickness type-II superlattices in resonant cavity mid-infrared light emitting diodes
In this study, we investigate the tradespace between the improvement of mid-infrared light-emitting diode efficiency through microcavity enhancement vs reduction of Auger recombination for different W-superlattice thicknesses. Several sample designs are modeled and then grown and fabricated to test the tradespace at different W-superlattice thicknesses down to the quantum well limit. In a half-cavity, with a single reflector from the top metal contact, intermediate thickness W-superlattices gave the highest efficiencies, outperforming those in the W-quantum well limit across the entire measured current range. Experimentally, we report wallplug efficiencies of 0.4% for a room temperature 3.2 μm device. W-superlattices of intermediate thickness were also found to be optimal for a full-cavity device with a bottom distributed Bragg reflector added. The resonant full cavity did strongly improve the peak spectral radiance, with a measured increase of four to five times for a 3.6 μm device, and a value that is >250 times larger than previously reported.
- 8 May 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (18)
Open AccessMicrocavity enhancement vs Auger recombination in variable thickness type-II superlattices in resonant cavity mid-infrared light emitting diodes
In this study, we investigate the tradespace between the improvement of mid-infrared light-emitting diode efficiency through microcavity enhancement vs reduction of Auger recombination for different W-superlattice thicknesses. Several sample designs are modeled and then grown and fabricated to test the tradespace at different W-superlattice thicknesses down to the quantum well limit. In a half-cavity, with a single reflector from the top metal contact, intermediate thickness W-superlattices gave the highest efficiencies, outperforming those in the W-quantum well limit across the entire measured current range. Experimentally, we report wallplug efficiencies of 0.4% for a room temperature 3.2 μm device. W-superlattices of intermediate thickness were also found to be optimal for a full-cavity device with a bottom distributed Bragg reflector added. The resonant full cavity did strongly improve the peak spectral radiance, with a measured increase of four to five times for a 3.6 μm device, and a value that is >250 times larger than previously reported.
- 17 March 2023
- Published by SPIE-Intl Soc Optical Eng
- Vol. PC12430, 34
Cascaded mid-infrared LEDs in resonant structures
As the efficiency of mid-infrared LEDs has advanced, they have assumed increasing importance in sensitive gas optical sensors, most prominently for methane and carbon, and LED arrays for defense-related projection systems. While cascading and superlattice quantum design has advanced efficiency, a key limiting mechanism in these devices is heavy loss from total internal reflection due to the very high index of refraction (~3.8). Here we report on the substantial enhancement of spectral radiance in one- and two-color LED emitters using a microcavity approach, and enhancement in overall radiance of single color emitters using micropillar structured devices.
- 17 March 2023
- Published by SPIE-Intl Soc Optical Eng
- Vol. PC12430, 34
Cascaded mid-infrared LEDs in resonant structures
As the efficiency of mid-infrared LEDs has advanced, they have assumed increasing importance in sensitive gas optical sensors, most prominently for methane and carbon, and LED arrays for defense-related projection systems. While cascading and superlattice quantum design has advanced efficiency, a key limiting mechanism in these devices is heavy loss from total internal reflection due to the very high index of refraction (~3.8). Here we report on the substantial enhancement of spectral radiance in one- and two-color LED emitters using a microcavity approach, and enhancement in overall radiance of single color emitters using micropillar structured devices.
- Open Access
- 11 October 2022
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 12 (11) , 4261-4267
Measurement of recombination mechanisms in mid-infrared W-superlattices
- 11 October 2022
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 12 (11) , 4261-4267
Open AccessMeasurement of recombination mechanisms in mid-infrared W-superlattices
- 15 February 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 118 (7) , 071105
High-power mid-wave infrared LED using W-superlattices and textured surfaces
Efficient mid-infrared light output has been obtained by incorporating a W-superlattice into a cascaded mid-infrared LED structure and by thinning and roughening of the emission side of the structure. At cryogenic temperatures, a radiance of ∼13.4 W/cm2-sr is achieved. Compared to the best published InAs/GaSb mid-IR LED, the maximum radiance is improved by ∼2.0×, while the wallplug efficiency improvement at the maximum radiance is improved >10×. For room temperature measurements on an un-thinned 400 μm diameter diode, the radiance (light output power) for a quasi-continuous wave and 1% duty cycle were ∼ 0.48 W/cm2-sr (2.4 mW) and ∼1.35 W/cm2-sr (6.8 mW), respectively. When compared to previous room temperature 4.2 μm LEDs, at a 1% duty cycle, this LED has optical powers that are 3× brighter. When compared to thermal emitters used in gas sensors, in the quasi-continuous wave, this LED uses ∼100× less energy per measurement.
- 15 February 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 118 (7) , 071105
High-power mid-wave infrared LED using W-superlattices and textured surfaces
Efficient mid-infrared light output has been obtained by incorporating a W-superlattice into a cascaded mid-infrared LED structure and by thinning and roughening of the emission side of the structure. At cryogenic temperatures, a radiance of ∼13.4 W/cm2-sr is achieved. Compared to the best published InAs/GaSb mid-IR LED, the maximum radiance is improved by ∼2.0×, while the wallplug efficiency improvement at the maximum radiance is improved >10×. For room temperature measurements on an un-thinned 400 μm diameter diode, the radiance (light output power) for a quasi-continuous wave and 1% duty cycle were ∼ 0.48 W/cm2-sr (2.4 mW) and ∼1.35 W/cm2-sr (6.8 mW), respectively. When compared to previous room temperature 4.2 μm LEDs, at a 1% duty cycle, this LED has optical powers that are 3× brighter. When compared to thermal emitters used in gas sensors, in the quasi-continuous wave, this LED uses ∼100× less energy per measurement.
- Open Access
- 10 February 2021
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 11 (3) , 719-728
Enhanced radiative and thermal properties from surface encapsulation of InAs nanowires
In this work, photoluminescence (PL), quantum efficiency and carrier dynamics are investigated in indium arsenide (InAs) nanowires (NWs) with various surface treatments, including a molecular beam epitaxy (MBE)-grown semiconductor shell passivation, sulfur-passivation, alumina (Al2O3) coating by atomic layer deposition (ALD) and polydimethylsiloxane (PDMS) spin-coating. The ALD-dielectric layer-coated InAs core-shell NWs show a maximum 13-fold increase in PL intensity. In contrast to the previous reports, this enhancement is found to be due to increased radiative rate from an enhanced Purcell factor, better thermal conductance and higher carrier injection within the NWs instead of improved surface quality. Numeric simulations confirm the experimentally observed increased radiative rate. Further improvements are suggested with even thicker capped InAs NWs. Carrier lifetime in surface-treated NWs is extended and shows long-term stability, critical for practical devices.
- 10 February 2021
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 11 (3) , 719-728
Open AccessEnhanced radiative and thermal properties from surface encapsulation of InAs nanowires
In this work, photoluminescence (PL), quantum efficiency and carrier dynamics are investigated in indium arsenide (InAs) nanowires (NWs) with various surface treatments, including a molecular beam epitaxy (MBE)-grown semiconductor shell passivation, sulfur-passivation, alumina (Al2O3) coating by atomic layer deposition (ALD) and polydimethylsiloxane (PDMS) spin-coating. The ALD-dielectric layer-coated InAs core-shell NWs show a maximum 13-fold increase in PL intensity. In contrast to the previous reports, this enhancement is found to be due to increased radiative rate from an enhanced Purcell factor, better thermal conductance and higher carrier injection within the NWs instead of improved surface quality. Numeric simulations confirm the experimentally observed increased radiative rate. Further improvements are suggested with even thicker capped InAs NWs. Carrier lifetime in surface-treated NWs is extended and shows long-term stability, critical for practical devices.
- 14 September 2020
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 10 (10) , 2470-2479
Long interior carrier lifetime in selective-area InAs nanowires on silicon
Catalyst-free, position-controlled indium arsenide (InAs) nanowires (NWs) of variable diameters were grown on Si (111) by selective-area epitaxy (SAE). Ultrafast pump-probe spectroscopy was conducted, from which carrier recombination mechanisms on the NW surface and interior were resolved and characterized. NWs grown using SAE demonstrated high optical quality, showing minority carrier lifetimes more than two-fold longer than that of the randomly-positioned (RP) NWs. The extracted SAE-InAs NW interior recombination lifetime was found to be as long as 7.2 ns, 13X longer than previous measurements on RP-NWs; and the surface recombination velocity 4154 cm · s- 1. Transmission electron microscopy revealed a high density of stacking defects within the NWs, suggesting that interior recombination lifetime can be further increased by improving NW interior crystalline quality.
- 14 September 2020
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 10 (10) , 2470-2479
Long interior carrier lifetime in selective-area InAs nanowires on silicon
Catalyst-free, position-controlled indium arsenide (InAs) nanowires (NWs) of variable diameters were grown on Si (111) by selective-area epitaxy (SAE). Ultrafast pump-probe spectroscopy was conducted, from which carrier recombination mechanisms on the NW surface and interior were resolved and characterized. NWs grown using SAE demonstrated high optical quality, showing minority carrier lifetimes more than two-fold longer than that of the randomly-positioned (RP) NWs. The extracted SAE-InAs NW interior recombination lifetime was found to be as long as 7.2 ns, 13X longer than previous measurements on RP-NWs; and the surface recombination velocity 4154 cm · s- 1. Transmission electron microscopy revealed a high density of stacking defects within the NWs, suggesting that interior recombination lifetime can be further increased by improving NW interior crystalline quality.