Satoshi Morooka

The lattice parameters of both the product phase and the matrix phase have determined using in situ X-ray and neutron diffraction measurements during forward and reverse transformations in steels. The lattice parameters are well known to be influenced by various factors, including temperature, internal stresses induced by transformation strains, partitioning of alloying elements, crystal defects, and magnetic strains. Therefore, it is crucial to accurately disentangle the contributions of these factors to the observed changes in lattice parameters. This review examines the evaluation of internal strain (stress) associated with ferrite, pearlite, bainite, martensite, and reverse austenite transformations, with a particular emphasis on the distinction between diffusional and displacive transformations. Additionally, the effects of plastic deformation of austenite on the bainite or martensite transformation are discussed. In this context, the roles of dislocations and vacancies are highlighted as key areas for further investigation.

Cracks due to stress corrosion cracking in stainless steels are becoming a problem not only in boiling water reactors but also in pressurized water reactor nuclear plants. Stress improvement measures have been implemented mainly for large-bore welded piping, but in the case of small-bore welded piping, post-welding stress improvement measures are often not possible due to dimensional restrictions, etc. Therefore, knowing the actual welding residual stresses of small-bore welded piping regardless of reactor type is essential for the safe and stable operation of nuclear power stations, but there are only a limited number of examples of measuring the residual stresses. In this study, austenitic stainless steel pipes with an outer diameter of 100 mm and a wall thickness of 11.1 mm were butt-welded. The residual stresses were measured by the strain scanning method using neutrons. Furthermore, to obtain detailed residual stresses near the penetration bead where the maximum stress is generated, the residual stresses near the inner surface of the weld were measured using the double-exposure method (DEM) with hard X-rays of synchrotron radiation. A method using a cross-correlation algorithm was proposed to determine the accurate diffraction angle from the complex diffraction patterns from the coarse grains, dendritic structures, and plastic zones. A quantum beam hybrid method (QBHM) was proposed that uses the circumferential residual stresses obtained by neutrons and the residual stresses obtained by the double-exposure method in a complementary use. The residual stress map of welded piping measured using the QBHM showed an area where the axial tensile residual stress exists from the neighborhood of the penetration bead toward the inside of the welded metal. This result could explain the occurrence of stress corrosion cracking in the butt-welded piping. A finite element analysis of the same butt-welded piping was performed and its results were compared. There is also a difference between the simulation results of residual stress using the finite element method and the measurement results using the QBHM. This difference is because the measured residual stress map also includes the effect of the stress of each crystal grain based on elastic anisotropy, that is, residual micro-stress.

An Fe-0.15C-5Mn-0.5Si-0.05Nb medium-Mn steel annealed at 660 °C and 685 °C both exhibited inhomogeneous deformation with Lüders deformation and followed by an extremely high work hardening stage, but with different Lüders strain and work hardening behavior. In-situ neutron diffraction measurements during tensile tests were performed to investigate changes in the phase stresses, the stress contribution to the strength of the constituent phases, and the crystal orientation of austenite. The role of each constituent phase on the deformation behavior and the crystallographic orientation dependence of austenite stability were examined. Deformation-induced martensite showed excellent phase stress and contributed to the strength of approximately 1000 MPa at around tensile strength, which is close to macroscopic tensile strength. Although austenite contributed less to the strength, during Lüders deformation and work hardening stages, it continuously transformed to martensite as the deformation progressed, suggesting that it mainly contributed to the ductility of the steels through a transformation-induced plasticity effect. Austenite transformed to martensite during Lüders deformation almost regardless of its crystallographic orientations. However, there was a tendency for more 311 oriented austenite grains to remain parallel to the tensile direction.

The mechanical properties of TRIP steels depend on heterogeneities of chemical composition and grain size in the retained γ structure, although these heterogeneities have not been characterized in detail. Therefore, in this study, we quantitatively investigate the inhomogeneous carbon concentration and grain size distribution, and its effects on the thermal stability of the retained γ in Fe-2Mn-1.5Si-0.4C (mass%) TRIP steel using FE-EPMA, EBSD, Mössbauer spectroscopy, and in-situ neutron diffraction during bainitic transformation at 673 K. In-situ neutron diffraction experiments detects high-carbon γ evolving during bainite transformation, in addition to the original γ, and the time variation of the volume fraction of high-carbon γ agrees well with the fraction of γ retained at room temperature. Williamson-Hall analysis based on peak width suggests that heterogeneity of carbon content exists even within the high-carbon γ. Compositional analysis using FE-EPMA and three-dimensional atom probe directly revealed that fine filmy γ was highly enriched with carbon compared to larger blocky γ, and the carbon content in blocky γ decreases with increasing blocky γ size. DICTRA simulation qualitatively reproduces the size dependency of carbon enrichment into γ. It was also found that γ tends to be retained at higher carbon content and smaller γ grain size since the smaller grain size directly improves thermal stability and the smaller γ size further contributes to the thermal stability via enhanced carbon enrichment.

Probabilistic fracture mechanics (PFM) is increasingly recognized as a viable approach for evaluating the structural integrity of nuclear components, such as piping, primarily affected by stress corrosion cracking (SCC). PFM analysis requires several input parameters, among which welding residual stress is critically important due to its significant influence on SCC initiation and propagation. Recently, a novel technique involving a double-exposure method (DEM) utilizing synchrotron X-rays was introduced as an effective means for measuring welding residual stress with high spatial resolution. In this paper, we applied DEM to assess the residual stress of a plate specimen, which was extracted from a welded pipe through electrical discharge machining. Consequently, detailed stress maps under a plane stress state were generated. Additionally, the residual stress distributions in the welded pipe under a triaxial stress state were evaluated using neutron diffraction. Based on these findings, we proposed a methodology to acquire detailed stress maps of welded pipes by combining high-energy synchrotron X-rays and neutron diffraction.