Carlo Bertorello

This work shows the performance of LincoSim, a web-based virtual towing tank enabling automated and standardized calm water computational fluid dynamics (CFD) data sampling, extending previous published applications to the case of a high-speed hull. The calculations are performed for a 1:10 scale model of a 43 ft powerboat hull form in the Froude number range from 0.3 to 2.0. The counterpart physical model is the experimental fluid dynamics (EFD) campaign performed at the University of Naples Federico II, where the resistance, sinkage and trim data have been measured. The EFD/CFD data comparison is performed and shown with a discussion of the spotted differences. The average percentage differences between the EFD and CFD data for the whole speed range are 1.84, 6.87 and 6.94 for the resistance, dynamic trim, and sinkage, respectively. These results confirm the maturity of the standardized and automated CFD modeling for calm water hydrodynamic analysis included in LincoSim, even at very high Froude numbers. The wetted length of the keel and chine and the wetted surface are calculated from numerical data using the advanced post-processing. Finally, as a work in progress, we test a first comparison for the same hull of the EFD and CFD data, considering two seakeeping conditions for head waves at a given wavelength for two velocity conditions. Also, this kind of analysis confirms the tight correlation between the measured and computed outcomes. This synergic interplay of EFD and CFD can link the advantages of both methods to support hull design but also requires experiment planning and final data analysis to obtain physical parameters not easily measurable in laboratory, such as the wetted surface, wetted lengths, proper viscous contribution, and pressure distribution both in calm water and in waves.

This paper reviews a state-of-the-art zero emission propulsion system for a battery-powered small craft. The main aspects considered are the available propulsion systems, energy storage, and dock battery charging. This underlying activity is part of the KISS project, a research and development program in the frame of the EU-funded “Piano Operativo Regionale CALABRIA FESR-FSE 2014–2020 ASSE I–PROMOZIONEDELLA RICERCA E DELL’INNOVAZIONE”, which is aimed at designing and building a physical prototype. Its hull form is based on previous research conducted by the authors, and the powering performances were preliminarily predicted by CFD simulation. The KISS project represents a successful example of an electric small craft with performances and a mission profile comparable to competitors with conventional propulsion. Such a target has been achieved by a concurrent design that considers the hull form, engine, propulsion system, and energy storage onboard. Safety issues and the regulatory frame are also highlighted.

In this paper, the validation of the hybrid frequency–time domain method for the assessment of hard chine displacement hull from vertical motions is presented. Excitation and hydrodynamic coefficients in regular waves are obtained from the 3D panel method by Hydrostar^® software, while coupled heave and pitch motions are calculated in the time domain by applying the Cummins equations. Experiments using a 1:15 scale model of a “low-drag” small craft are performed in irregular head and following waves at Froude numbers Fr: 0.2, 0.4, and 0.6 at University of Naples Federico II, Italy. Results obtained by hybrid frequency–time domain simulations for heave, pitch, and vertical accelerations at center of gravity and bow are compared with experimental data and showed high accuracy.

A proper design of the mooring systems for Wave Energy Converters (WECs) requires an accurate investigation of both operating and extreme wave conditions. A careful analysis of these systems is required to design a mooring configuration that ensures station keeping, reliability, maintainability, and low costs, without affecting the WEC dynamics. In this context, an experimental campaign on a 1:20 scaled prototype of the ISWEC (Inertial Sea Wave Energy Converter), focusing on the influence of the mooring layout on loads in extreme wave conditions, is presented and discussed. Two mooring configurations composed of multiple slack catenaries with sub-surface buoys, with or without clump-weights, have been designed and investigated experimentally. Tests in regular, irregular, and extreme waves for a moored model of the ISWEC device have been performed at the University of Naples Federico II. The aim is to identify a mooring solution that could guarantee both correct operation of the device and load carrying in extreme sea conditions. Pitch motion and loads in the rotational joint have been considered as indicators of the device hydrodynamic behavior and mooring configuration impact on the WEC.

IJSCT - International Journal of Small Craft Technology Part B of The Royal Institution of Naval Architects transactions technical papers