Renata de Bello Solcia Guerrero
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Renata de Bello Solcia Guerrero has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Carla Eloísa Diniz dos Santos
Universidade Federal do Triângulo Mineiro image/svg+xml
4 shared publications - Denise Bevilaqua
São Paulo State University-UNESP
3 shared publications - Marcelo Zaiat
Laboratory of Biological Processes, Center for Research, Development and Innovation in Environmental Engineering, São Carlos School of Engineering, University of São Paulo (USP), São Carlos, Brazil
3 shared publications - Márcia Helena Rissato Zamariolli Damianovic
Biological Processes Laboratory (LPB), São Carlos School of Engineering (EESC), University of São Paulo (USP), Av. João Dagnone, 1100, Santa Angelina, São Carlos, São Paulo 13563-120, Brazil
3 shared publications - Eugenio Foresti
Biological Processes Laboratory, São Carlos School of Engineering (EESC), University of São Paulo (USP), São Carlos, Brazil
2 shared publications - Leandro Augusto Gouvêa de Godoi
Departamento de Hidráulica e Saneamento, Escola de Engenharia de São Carlos Universidade de São Paulo Sao Carlos Brazil
2 shared publications
Latest Publications
- 1 September 2019
- Published by Elsevier in Bioresource Technology
- Vol. 288, 121529
Establishing simultaneous nitrification and denitrification under continuous aeration for the treatment of multi-electrolytes saline wastewater
- 1 September 2019
- Published by Elsevier in Bioresource Technology
- Vol. 288, 121529
Establishing simultaneous nitrification and denitrification under continuous aeration for the treatment of multi-electrolytes saline wastewater
- 16 May 2019
- Published by Taylor & Francis in International Journal of Environmental Analytical Chemistry
- Vol. 99 (9) , 809-823
Rapid and easy quantification of elemental sulphur in aqueous samples from biological reactors: the turbidimetric method revisited
Recent developments in wastewater treatment have led to a renewed interest to obtain elemental sulphur (S°) as a by-product from bioreactors. However, practical studies are limited by the gap of adequate analytical techniques for its determination. This paper provides a statistical study and matrix effect evaluation of an adapted spectrophotometric method for routine S° analyses in aqueous samples, based on a methodology previously described by Hart (1961). Four complex matrices were tested: domestic sewage and effluent samples from three different bioreactors. Tested performance criteria included linearity, matrix effect, limit of detection and quantification and S° recovery. Results were linear (R2 = 0.99994) in the studied range (5 to 100 mg S° L−1) and no matrix effect was observed. The accuracy was based on recovery values that varied from 100% to 106%. The colloidal S° separation and extraction protocol was also considered suitable for aqueous samples, reaching more than 99.0% of S° recovery.
- 16 May 2019
- Published by Taylor & Francis in International Journal of Environmental Analytical Chemistry
- Vol. 99 (9) , 809-823
Rapid and easy quantification of elemental sulphur in aqueous samples from biological reactors: the turbidimetric method revisited
Recent developments in wastewater treatment have led to a renewed interest to obtain elemental sulphur (S°) as a by-product from bioreactors. However, practical studies are limited by the gap of adequate analytical techniques for its determination. This paper provides a statistical study and matrix effect evaluation of an adapted spectrophotometric method for routine S° analyses in aqueous samples, based on a methodology previously described by Hart (1961). Four complex matrices were tested: domestic sewage and effluent samples from three different bioreactors. Tested performance criteria included linearity, matrix effect, limit of detection and quantification and S° recovery. Results were linear (R2 = 0.99994) in the studied range (5 to 100 mg S° L−1) and no matrix effect was observed. The accuracy was based on recovery values that varied from 100% to 106%. The colloidal S° separation and extraction protocol was also considered suitable for aqueous samples, reaching more than 99.0% of S° recovery.
- Open Access
- 8 March 2019
- Published by MDPI AG in Chemengineering
- Vol. 3 (1) , 27
Evaluation of Biogas Biodesulfurization Using Different Packing Materials
The packing material selection for a bioreactor is an important factor to consider, since the characteristics of this material can directly affect the performance of the bioprocess, as well as the investment costs. Different types of low cost packing materials were studied in columns to reduce the initial and operational costs of biogas biodesulfurization. The most prominent (PVC pieces from construction pipes) was applied in a bench-scale biotrickling filter to remove the H2S of the biogas from a real sewage treatment plant in Brazil, responsible for 90 thousand inhabitants. At the optimal experimental condition, the reactor presented a Removal Efficiency (RE) of up to 95.72% and Elimination Capacity (EC) of 98 gS·m−3·h−1, similar to open pore polyurethane foam, the traditional material widely used for H2S removal. These results demonstrated the high potential of application of this packing material in a full scale considering the robustness of the system filled with this support, even when submitted to high sulfide concentration, fluctuations in H2S content in biogas, and temperature variations.
- 8 March 2019
- Published by MDPI AG in Chemengineering
- Vol. 3 (1) , 27
Open AccessEvaluation of Biogas Biodesulfurization Using Different Packing Materials
The packing material selection for a bioreactor is an important factor to consider, since the characteristics of this material can directly affect the performance of the bioprocess, as well as the investment costs. Different types of low cost packing materials were studied in columns to reduce the initial and operational costs of biogas biodesulfurization. The most prominent (PVC pieces from construction pipes) was applied in a bench-scale biotrickling filter to remove the H2S of the biogas from a real sewage treatment plant in Brazil, responsible for 90 thousand inhabitants. At the optimal experimental condition, the reactor presented a Removal Efficiency (RE) of up to 95.72% and Elimination Capacity (EC) of 98 gS·m−3·h−1, similar to open pore polyurethane foam, the traditional material widely used for H2S removal. These results demonstrated the high potential of application of this packing material in a full scale considering the robustness of the system filled with this support, even when submitted to high sulfide concentration, fluctuations in H2S content in biogas, and temperature variations.
- 24 May 2018
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 93 (12) , 3483-3491
Dynamics of the nitrification and sulfide‐driven autotrophic denitrification processes in a single reactor using oxidation–reduction potential as an indicator of the process effectiveness
BACKGROUND: This paper evaluates the nitrification and sulfide‐driven autotrophic denitrification processes in a structured‐bed reactor subjected to recirculation and intermittent aeration (SBRRIA) applied to the post‐treatment of an anaerobic effluent. The SBRRIA reactor was operated during 130 days in which influent sulfide concentrations varied between 220.1 and 231.0 mg TDS L−1 (TDS, total dissolved solids). Temporal tests were performed to elucidate the dynamics and sulfide impacts on combined processes.RESULTS: Sulfide partially inhibited the nitrifying activity, resulting in low NH4+‐N oxidation. This fact affected the overall nitrogen removal performance as total‐N removal efficiencies of 50 and 55% were attained in Conditions III and IV, respectively. On the one hand, under continuous aeration and in the absence of sulfide, the oxidation–reduction potential (ORP) reached 50 mV (versus Ag/AgCl) after 250 min of experiment. On the other, when sulfide was continuously provided in the feeding, the ORP was maintained lower than zero. Under anoxic conditions, the effective use of sulfide as an electron donor by autotrophic denitrification was verified by ORP monitoring. However, a concentration of 260 mg TDS L−1 associated with high pH proved inhibitory for NO3− reduction.CONCLUSIONS: Based on the results obtained, new strategies of adding sulfide to the SBRRIA should be tested to minimize its inhibitory effect on nitrification and improve nitrogen removal in this unit. © 2018 Society of Chemical Industry
- 24 May 2018
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 93 (12) , 3483-3491
Dynamics of the nitrification and sulfide‐driven autotrophic denitrification processes in a single reactor using oxidation–reduction potential as an indicator of the process effectiveness
BACKGROUND: This paper evaluates the nitrification and sulfide‐driven autotrophic denitrification processes in a structured‐bed reactor subjected to recirculation and intermittent aeration (SBRRIA) applied to the post‐treatment of an anaerobic effluent. The SBRRIA reactor was operated during 130 days in which influent sulfide concentrations varied between 220.1 and 231.0 mg TDS L−1 (TDS, total dissolved solids). Temporal tests were performed to elucidate the dynamics and sulfide impacts on combined processes.RESULTS: Sulfide partially inhibited the nitrifying activity, resulting in low NH4+‐N oxidation. This fact affected the overall nitrogen removal performance as total‐N removal efficiencies of 50 and 55% were attained in Conditions III and IV, respectively. On the one hand, under continuous aeration and in the absence of sulfide, the oxidation–reduction potential (ORP) reached 50 mV (versus Ag/AgCl) after 250 min of experiment. On the other, when sulfide was continuously provided in the feeding, the ORP was maintained lower than zero. Under anoxic conditions, the effective use of sulfide as an electron donor by autotrophic denitrification was verified by ORP monitoring. However, a concentration of 260 mg TDS L−1 associated with high pH proved inhibitory for NO3− reduction.CONCLUSIONS: Based on the results obtained, new strategies of adding sulfide to the SBRRIA should be tested to minimize its inhibitory effect on nitrification and improve nitrogen removal in this unit. © 2018 Society of Chemical Industry
- 1 August 2017
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 262, 682-686
Evaluation of Substrate Consumption Kinetics in Different Support Materials for Biotrickling Filters Aiming Biogas Desulfurization
Biogas is a renewable energy source that can be used to produce heat and energy, replacing fossil fuels. The main factor limiting the use of biogas is contaminants in its composition which H2S is the most important due to corrosion and environmental problems. A promising technology to remove this contaminant from biogas is the biotrickling filters and the selection of inexpensive and durable supports is an important step for the operation. This work has studied different support materials, for microorganisms immobilization, as Polyvinyl Chloride (PVC), Polyethylene Terephtalate (PET), Polytetrafluoroethylene (Teflon®) comparing to open pore polyurethane foam (OPP) each one packed in biotrickling filters to evaluate the consumption of thiosulfate by chemolitotrofic microorganisms. The kinetics of substrate consumption in different cycles for each support were distinct suggesting different microbial colonization. The materials tested have presented results very similar polyurethane foam, which has already known by its efficiency on biogas desulfurization, unless Teflon that has showed a divergent result with the increase of the substrate concentration in the system.
- 1 August 2017
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 262, 682-686
Evaluation of Substrate Consumption Kinetics in Different Support Materials for Biotrickling Filters Aiming Biogas Desulfurization
Biogas is a renewable energy source that can be used to produce heat and energy, replacing fossil fuels. The main factor limiting the use of biogas is contaminants in its composition which H2S is the most important due to corrosion and environmental problems. A promising technology to remove this contaminant from biogas is the biotrickling filters and the selection of inexpensive and durable supports is an important step for the operation. This work has studied different support materials, for microorganisms immobilization, as Polyvinyl Chloride (PVC), Polyethylene Terephtalate (PET), Polytetrafluoroethylene (Teflon®) comparing to open pore polyurethane foam (OPP) each one packed in biotrickling filters to evaluate the consumption of thiosulfate by chemolitotrofic microorganisms. The kinetics of substrate consumption in different cycles for each support were distinct suggesting different microbial colonization. The materials tested have presented results very similar polyurethane foam, which has already known by its efficiency on biogas desulfurization, unless Teflon that has showed a divergent result with the increase of the substrate concentration in the system.
- 1 March 2014
- Published by Elsevier in Biochemical Engineering Journal
- Vol. 84, 1-8
Hydrogen sulphide removal from air by biotrickling filter using open-pore polyurethane foam as a carrier
- 1 March 2014
- Published by Elsevier in Biochemical Engineering Journal
- Vol. 84, 1-8
Hydrogen sulphide removal from air by biotrickling filter using open-pore polyurethane foam as a carrier